Skip to main content
SpringerLink
Log in

Model development of flexible disk grinding process

  • Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design
  • Published:
KSME International Journal Aims and scope Submit manuscript

Abstract

A flexible disk grinding process model was developed based on the dynamic relationship proposed by Kurfess and the influence of the major system parameters which potentially affect the grinding process was studied. Due to the process complexities, several new parameters were assumed to be kinematically dependent on the geometric layouts of the process. Different process stages had been defined depending on the kinematic relationships between the grinding disk and workpiece. A trend of depth of cut was simulated using the proposed model and compared with the empirically measured data in two dimensions. Due to a poor prediction capability of the first model, a modified model was proposed and a better performance has been proved to reveal a closer description of processed surface quality. Also a deflection length has been verified using a different analytical approach.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  • Chen, X., Rowe, W. B., Allanson, D. R. and Mills, B., 1999, “A Grinding Power Model for Selection of Dressing and Grinding Conditions,”Trans. of the ASME, J. of Manu. Sd. and Eng., Vol. 121, pp. 632–637.

    Article  Google Scholar 

  • Dornfeld, D. A., 1981, “Single Grit Simulation of the Abrasive Machining of Wood,”Trans. ASME, J. Eng. Ind., Vol. 103, No. 1, pp. 1–12.

    Article  Google Scholar 

  • Ikuse, Y. and Unno, K., 1999, “Study on Deducing Elastic Modulus of Super Abrasive Grinding Wheel Using Acoustic Model,”J. of the Japan Soc. for Pree. Eng., Vol. 65, No. 8, pp. 1174–1179.

    Google Scholar 

  • Jenkins, H. E., Kurfess. T. R. and Ludwick, S. J., 1997, “Determination of a Dynamic Grinding Model,”Trans of ASME, J. of Dyn. Sys. Measurement & Control, Vol. 119, No. 2, pp. 289–293.

    Article  MATH  Google Scholar 

  • Kegg, R. L., 1983, “Industrial problems in grinding,”Annals of the CIRF, Vol. 32, No. 2, pp. 559–56l.

    Article  Google Scholar 

  • King, R. I. and Hahn, R. S., 1986,Handbook of Modern Grinding Technology, Chapman and Hall, New York.

    Google Scholar 

  • König, W., 1982 “A Numerical Method to Describe the Kinematics of Grinding,”Annals of the CIRF, Vol. 31, No. 1, pp. 201–204.

    Article  Google Scholar 

  • Kurfess, T. R., 1987, “Verification of a Dynamic Grinding Model,” MIT Mechanical Eng. M. S. Thesis.

  • Lindsay, R. P. and Hahn, R. S., 1971, “On the Basic Relationship Between Grinding Parameters,”Annals of the CIRF, Vol. 19, No. 4, pp. 657–664

    Google Scholar 

  • Malkin, S. and Koren, Y., 1980, “Off-line Grinding Optimization with a Micro-Computer,” Annals of the CIRF, Vol. 29, No. 1, pp. 213–216 Malkin, S., 1987, “Practical Grinding Optimization,”Proc. 15th NAMRC, SME, Lehigh Univ., Bethlehem Pennsylvania, pp. 123–140.

    Article  Google Scholar 

  • Miller, M. H. and Dow, T. A., 1999, “Influence of the Grinding Wheel in the Ductile Grinding of Brittle Materials: Development and Verification of Kinematic Based Model,”Trans. of ASME, J. of Manufact. Sci. & Eng., Vol. 121, No. 4, pp. 638–646.

    Article  Google Scholar 

  • Pahlizsch, G., 1970, “Internationaler Atand der Forschung auf dem Gebiet des Schleifen von Holtz,” Holz als Roh- und Werkstoff, Vol. 28, No. 9, pp. 329–343

    Article  Google Scholar 

  • Pandit, S. M. and Wu, S. M., 1973, “Characterization of Abrasive Tools by Continuous Time Series,”Trans. ASME, J. Eng. Ind., Vol. 95, No. 1, pp. 821–825.

    Google Scholar 

  • Park, K. W., Lee, J. H., Oh, B. 0. and Lee, M. K., 2000, “Development of Robot Control and Measurement for Unknown Geometric Surface Grinding,”Trans. of the KSME, Vol. 24, No. 4, pp. 1039–1046 (In Korean).

    Google Scholar 

  • Sathyanarayanan, G., 1985, “Two Wavelength Characteristic Grain Model for Grinding Wheel,”Annals of the CIRP, Vol. 34, No. 1, pp. 299–303.

    Article  Google Scholar 

  • Seo, T. I. and Cho, M. W., 1999, “Tool Trajectory Generation Based on Tool Deflection Effects in the Flat-End Milling Process (II)-Prediction and Compensation of Milled Surface Error,”KSME Int’l J., Vol. 13, No. 12, pp. 9l8–930.

    Google Scholar 

  • Spur, G. and Stark, C., 1984, “Method for Grinding Wheel Quality,”Proc. 12th NAMRC, SME, Houghton, Michigan, pp. 339–346.

Download references

Author information

Authors and Affiliations

  1. College of Mechanical and Industrial System Engineering, Kyung Hee University, Yongin-si, 1, 449-701, Kyungki-do, Korea

    Song-Min Yoo, Myung-Jin Choi & Young-Jin Kim

Authors
  1. Song-Min Yoo
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Myung-Jin Choi
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Young-Jin Kim
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Song-Min Yoo.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Yoo, SM., Choi, MJ. & Kim, YJ. Model development of flexible disk grinding process. KSME International Journal 14, 1114–1121 (2000). https://doi.org/10.1007/BF03185065

Download citation

  • Received:

  • Revised:

  • Issue Date:

  • DOI: https://doi.org/10.1007/BF03185065

Key Words

Search

Navigation