Abstract
This work developed improved slip factor model and correction method to predict flow through impeller in forward-curved centrifugal fan. Both steady and unsteady three-dimensional CFD analyses were performed to validate the slip factor model and the correction method. The results show that the improved slip factor model presented in this paper could provide more accurate predictions for forward-curved centrifugal impeller than the other slip factor models since the present model takes into account the effect of blade curvature. The correction method is provided to predict mass-averaged absolute circumferential velocity at the exit of impeller by taking account of blockage effects induced by the large-scale backflow near the front plate and flow separation within blade passage. The comparison with CFD results also shows that the improved slip factor model coupled with the present correction method provides accurate predictions for mass-averaged absolute circumferential velocity at the exit of impeller near and above the flow rate of peak total pressure coefficient.
Similar content being viewed by others
Abbreviations
- a:
-
Effective passage width
- b:
-
Blade width
- BF :
-
Blockage coefficient due to backflow near the front plate
- BS :
-
Blockage coefficient due to flow separation from suction surface
- Cr, Cu, Cz :
-
Absolute velocity component in radial, circumferential, axial direction, respectively
- Cm :
-
Meridional velocity (nearly equal to Cr at the exit of impeller)
- D:
-
Diameter
- n:
-
Perpendicular direction to flow
- p:
-
Static pressure
- pt :
-
Total pressure
- Q:
-
Volume flow rate
- R:
-
Radius
- Rb :
-
Radius of curvature of blade
- Rv :
-
Radius of scroll (as shown in Figure 1)
- s:
-
Flow direction
- t:
-
Blade thickness
- T:
-
Wake width
- U:
-
Peripheral speed
- w:
-
Relative velocity
- W:
-
Scroll width
- z:
-
Blade number
- α v :
-
Scroll angle
- θ c :
-
Cutoff angle (as shown in Figure 1)
- θ v :
-
Scroll angle from the origin (as shown in Figure 1)
- β:
-
Blade angle
- δ:
-
Opening angle of blade camber at the exit
- ε:
-
Total blockage coefficient
- γ:
-
Flow deflection angle in the discharge stream of blade
- ϕ:
-
Flow coefficient (=Q/πb 2 D 2 U 2)
- μ:
-
Slip factor (=C u2′/C u2)
- ρ:
-
Flow density
- ω:
-
Rotating speed
- ψ:
-
Total pressure coefficient (=Δp t ρU 22 )
- 1, 2:
-
Impeller inlet, outlet or blade tip
- \(\left( - \right)\) :
-
Area-averaged quantity
- \(\left( - \right)\) :
-
Mass-averaged quantity (Prime values denote actual flow angle and velocity with slip considered)
References
Eck, B., 1973, “Fans,” 1st ed., Pergamon Press, New York.
Kim, J. K. and Kang, S. H., 1997, “Effects of the Scroll on the Performance and Flow Field of a Sirocco Fan,” ISROMAC-7, Hawaii, pp. 1318–1327.
Kind, R. J. and Tobin, M. G., 1990, “Flow in a Centrifugal Fan of the Squirrel-Cage Type,”ASME Journal of Turbomachinery, Vol. 112, pp. 84–90.
Kind, R. J., 1997, “Prediction of Flow Behavior and Performance of Squirrel-Cage Centrifugal Fans Operating at Medium and High Flow Rates,”ASME Journal of Fluids Engineering, Vol. 119, Sept., pp. 639–646.
Kwon, E. Y. and Cho, N. H., 2001, “Experimental Study on the Mean Flow Characteristics of Forward-Curved Centrifugal Fans,”KSME International Journal, Vol. 15, No. 12, pp. 1728–1738.
Raj, D. and Swim, W. B., 1981, “Measurements of the Mean Flow Velocity and Velocity Fluctuations at the Exit of an FC Centrifugal Fan Rotor,”ASME Journal of Engineering for Power, Vol. 103, April, pp. 393–399.
Sandra Velarde-Suarez et al., 1999, “Experimental Study on the Aeroacoustic Behavior of a Forward-Curved Blades Centrifugal Fan,”ASME Journal of Fluids Engineering, Vol. 121, pp. 276–281.
Senoo, Y. et al, 1974, “Viscous Effects on Slip Factor of Centrifugal Blowers,” ASME Journal of Engineering for Power, January, pp. 59–65.
Seo, S. J., Kim, K. Y. and Kang, S. H., 2003, “Calculations of Three-Dimensional Viscous Flow in A Multi-Blade Centrifugal Fan by Modeling Blade Forces,” Proceedings of The Institution of Mechanical Engineers, Part A-Journal of Power and Energy, Vol. 217, No. 3, pp. 287–298.
Stodola, A., 1927, “Steam and Gas Turbines,” McGraw-Hill, New York.
Thomas Bouquet et al., 2002, “Study of the 3D Flows in the Forward-Curved Blades Centrifugal Fans,” Proceedings of ASME 2002 Fluids Engineering Division Summer Meeting, Montreal, Quebec, Canada, July 14–18, 2002.
Wiesner, F. J., 1967, “Review of Slip Factors for Centrifugal Impellers,”ASME Journal of Engineering for Power, Oct., pp. 558–572.
Yamazaki, S., 1986, “An Experimental Study on the Aerodynamic Performance of Multi-Blade Blowers (1st Report),”Transactions of JSME (B), Vol. 52, No. 484, pp. 3987–3992.
Yamazaki, S., 1987a, “An Experimental Study on the Aerodynamic Performance of Multi-Blade Blowers (2nd Report),”Transactions of JSME (B), Vol. 53, No. 485, pp. 108–113.
Yamazaki, S., 1987b, “An Experimental Study on the Aerodynamic Performance of Multi-Blade Blowers (3rd Report),”Transactions of JSME (B), Vol. 53, No. 490, pp. 1730–1735.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Guo, EM., Kim, KY. Three-dimensional flow analysis and improvement of slip factor model for forward-curved blades centrifugal fan. KSME International Journal 18, 302–312 (2004). https://doi.org/10.1007/BF03184740
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF03184740