Zusammenfassung
Das Institut für Eisenhüttenkunde — Experimentelle und numerische Prozess-Simulation — Mikrostrukturelle und makroskopische Charakterisierung — Multiphasenstähle — Hochtemperatur-Tauchbeschichten — Hochtemperatureinsatzhärten — Vorhersage der Hochlagenzähigkeit mit Hilfe schädigungsmechanischer Simulationen — Beeinflussung der Grenzflächenreaktionen beim Bandverzinken — Lasergestützte 3D-Formänderungsanalyse
Abstract
The Department of Ferrous Metallurgy — Experimental and numerical process-simulation — Microstructural and macroscopic characterization — Multiphase steels — High-temperature dipping process — High-temperature carburization — Prediction of ductility using damage mechanism simulation — Improving the interface reaction for strip galvanizing — Laser-aided 3D-deformation analysis.
Literaturverzeichnis
Bleck, W., undD. Senk (Hrsg.): IEHK Report 2004/2005, Verlag Mainz, Aachen.
Prahl, U.: Werkstoff- und Prozessentwicklung mit Hilfe experimenteller und numerischer Simulation. In:W. Bleck (Hrsg.), Zunkunft für Stahl — Stahl, ist Zukunft; 20. Aachener Stahlkolloquium 2005, Verlag Mainz, Aachen.
Prahl, U., U. Lorenz, F. Gerdemann, A. Guindani andW. Bleck: Numerical and experimental parameter identification for processing of hot rolled dual phase steel. In:M. Lamberights (Hrsg.), 2nd Conference on Thermonechanical Processing of Steels TMP04, 2004, B-Liège Stahl-Eisen, Düsseldorf.
Kiekel, A.: Prozess- und Werkstoffoptimierung von metallischen Schichtverbund-werkstoffen, hergestellt durch das Verfahren des Tauchbeschichtens bei hohen Schmelztemperaturen. Diss. RWTH Aachen, Shaker Verlag, 2003.
Bleck, W., G. Pariser, S. Trute andC. Klinkenberg: New developments for microalloyed heat treating steels. In THERMEC 2003. Int. Conf. on Processing & Manufacturing of Advanced Materials, 7.–11.7.2003. Madrid, Spanien, Hrsg.:T. Chandra et al., Part 2. Materials Science Forum 426/432. Uetikon-Zürich: Trans Tech Publ. 2003, 1201–1206.
Gurson, A. L.: Continuum theory of ductile rupture by void nucleation and growth: Part I — Yield criteria and flow rules for porous ductile media. J. Engn. Mater. Tech.99 (1977), 2–15.
Tvergaard, V.: On localization in ductile materials containing spherical voids. Int. J. Fract.18 (1982), 237–252.
Tvergaard, V., andA. Needleman: Analysis of the cup-cone fracture in a round tensile bar. Acta Metall., Vol. 32, No. 1 (1984), 157–159.
Münstermann S., P. Langenberg undM. Seidenfuß: Numerische Bestimmung von duktilen Rissinitilerungskennwerten unter Berücksichtigung der Mikrostruktur. Deutscher Verband für Materialforschung und-prüfung e. V., Tagungsband zur 37. Tagung des DVM-Arbeitskreises Bruchvorgänge, 22. und 23. Februar 2005 an der TU Hamburg-Harburg, ISSN 16164687.
Staudte J.: Surface Conditioning of High-Strength Steels, Diss. RWTH Aachen, 2003.
Beste, D., undF. Luther: Verfahrensvariation bei der Feuerverzinkung hochfester Stähle. In:W. Bleck (Hrsg.), Zukunft für Stahl — Stahl ist Zukunft; 20 Aachener Stahlkolloquium 2005, Verlag Mainz, Aachen.
Hennion, A., J. F. Noville, G. Leprince, E. Senet andM. Soler: Pilot section of reactive continuous annealing. European Commission, Luxembourg, (2003) EUR 20910.
Gologranc, F.: Beitrag zur Ermittlung von Fließkurven im kontinuierlichen hydraulischen Tiefungsversuch, Diss. Univ. Stuttgart, 1975.
Bleck, W., andM. Blumbach: Laser-aided flow curve determination in hydraulic bulging. Steel Research Int.76 (2005). No. 2/3, 125–130.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Bleck, W., Heßling, G. & Prahl, U. Werkstofftechnische Forschung am Institut für Eisenhüttenkunde der RWTH Aachen. Berg Huettenmaenn Monatsh 150, 379–385 (2005). https://doi.org/10.1007/BF03169080
Issue Date:
DOI: https://doi.org/10.1007/BF03169080