Abstract
As a part II of theis research, new local inspection planning strategy is proposed in this paper based on the proposed inspection feature extraction method. In the local inspection planning stage, each feature is decomposed into its constituent geometric elements for more effective inspection planning. The local inspection planning for the decomposed features are performed to determine: (l) the suitable number of measuring points, (2) their locations, and (3) the optimum probing paths to minimize measuring errors and times. The fuzzy set theory, the Hammersley’s algorithm and the TSP method are applied for the local inspection planning. Also, a new collision checking algorithm is proposed for the probe and/or probe holder based on the Z-map concept. Finally, the results are simulated and analyzed to verify the effectiveness of the proposed methods.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Caskey, G., Hari, Y., Hocken, R., Palanivelu, D., Raja, J., Wilson, R., Chen, K. and Yang, J., 1990, “Sampling Techniques for Coordinate Measuring Machine,”Design and Manufacturing Systems Conference, pp. 779–786.
Chang, T. C., and Wysk, R. A., 1985, An Introduction to Process Planning Systems, Prentice-Hall, Englewood cliffs, New Jersey, USA.
Cho, M. W. and Kim, K., 1995, “New Inspection Planning Strategy for Sculptured Surfaces Using Coordinate Measuring Machine,”International Journal of Production Research, Vol. 33, No. 2, pp. 427–444.
Cho, M. W. and Seo, T. I., 2002, “Inspection Planning Strategy for the On-Machine Measurement Process Based on CAD/CAM/CAI Integration Concept,”The International Journal of Advanced Manufacturing Technology, Vol. 19, pp. 607–617.
Cho, M. W., Seo, T. I., Kim, J. D. and Kwon, O. Y., 2000, “Reverse Engineering of Compound Surfaces Using Boundary Detection Method,”KSME International Journal, Vol. 14, No. 10, pp. 1104–1113.
Descotte, Y. and Latombe, J. C., 1984,GARI: An Expert System for Process Planning, Solid Modeling by Computers, pp. 329–345, Plenum Press, NY.
Lee, G., Mou, J. and Shen, Y., 1997, “Sampling strategy design for Dimensional Measurement of Geometric Features Using Coordinate Measuring Machine,”International Journal of Machine Tools and Manufacturing, Vol. 37, No. 7, pp. 917–934.
Lee, J. W., Kim, M. K. and Kim, K., 1994, “Optimal Probe Path Generation and New Guide Point Selection Methods,”Engineering Application of Artificial Intelligence, Vol. 7, No. 4, pp. 439–445.
Lee, K. I., Lee, H., Noh, S. D., Shim, Y. B., and Cho, H. S., 1995, “A Process Planning System Using Group Technology and Rule-base,”IE Interfaces, Korean Institute of Industrial Engineers, Vol. 8, No. 3, pp. 221–230.
Menq, C. H., Yau, H. T., Lai, G. Y. and Miller, R. A., 1990, “Statistical Evaluation of Form Tolerances Using Discrete Measurement Data,”ASME Winter Annual Meeting, ASME, PED-Vol. 47, pp. 135–149.
Press, W. H., Teukolsky, S. A., Vetterling, W. T. and Flannery, B. P., 1992,Numerical Recipes in C, Cambridge University Press.
Rogers, M., 1994, “Case Study of Feature Representation in STEP,” Part 48, Technical Report, Design Automation Laboratory, Department of Mechanical Engineering, Arizona State University, USA.
Shah, J. J., Mantyla, M., and Nau, D. D., 1994,Advances in Feature-Based Manufacturing, Elsevier Science B. V., Amsterdam, Netherlands.
Woo, T. C. and Liang, R., 1993, “Dimensional measurement of surfaces and their sampling,”Computer-Aided Design, Vol. 25, No. 4, pp. 233–239.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Cho, MW., Lee, H., Yoon, GS. et al. A computer-aided inspection planning system for on-machine measurement — Part II: Local inspection planning —. KSME International Journal 18, 1358–1367 (2004). https://doi.org/10.1007/BF02984250
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF02984250