Journal of Materials Shaping Technology

, Volume 8, Issue 2, pp 133–141 | Cite as

Extrusion through controlled strain rate dies

  • R. Srinivasan
  • J. S. Gunasekera
  • H. L. Gegel
  • S. M. Doraivelu
Article

Abstract

The workability of a material during deformation processing is determined by (a) the die geometry which, in turn, determines the flow field during deformation, and, (b) the inherent workability of the material under the imposed processing conditions of strain rate and temperature. Most common alloys have good inherent workability and can be successfully formed over wide ranges of temperature and strain rate. Products can be successfully formed from these alloys even with dies which impose large variations in strain rate during deformation. However, many of the new alloys and composites can be deformed only in very narrow processing regimes, and control of the strain rate during deformation of such materials becomes important. For example, extrusion of a whisker-reinforced aluminum alloy composite is possible only when the strain rate is controlled to within one order of magnitude. This paper describes the development of a method for obtaining preliminary shapes of controlled strain rate extrusion dies, a special case being the constant strain rate die. The theoretical basis for such die design processes is presented, followed by some examples of die geometries. Since this design procedure ignores the material flow properties, the designed die shapes must be verified using the finite element method or physical modeling. Results of simulations with the program ALPID are also presented.

Keywords

Constant Strain Rate Extrusion Ratio Material Shaping Technology Finite Element Simulation Result Control Strain Rate 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Y.V.R.K. Prasad, H.L. Gegel, S.M. Doraivelu, J.C. Malas, J.T. Morgan, K.A. Lark, and D.R. Barker, “Modeling of Dynamic Materials Behavior in Hot Deformation: Forging of Ti 6242,”Met. Trans. 15A, p. 1883 (1984).Google Scholar
  2. 2.
    Y.V.R.K. Prasad, H.L. Gegel, J.C. Malas, J.T. Morgan, K.A. Lark, S.M. Doraivelu, and D.R. Barker, “Constitutive Behavior and Dynamic Modeling of Hot Deformation of a P.M 2024 Al Alloy with 20 Vol.% SiC Dispersion,” Technical Report AFWAL-TR-84-4076, Air Force Wright Aeronautical Laboratories, Wright-Patterson AFB, November 1984.Google Scholar
  3. 3.
    J.C. Malas, H.L. Gegel, J.S. Gunasekera, S.M. Doraivelu, and J.T. Morgan, “Computer-Aided Design of Extrusion Dies by Metal-Flow Simulation,” inComputers in Engineering 1983 American Society of Mechanical Engineers, New York, 1983.Google Scholar
  4. 4.
    H.L. Gegel, J.S. Gunasekera, J.C. Malas, J.T. Morgan, and L.E. Matson, “Consolidation and Forming of P/M Porous Billets,” inRapid Solidification Processing Principles and Technologies, III, R. Mehrabian, Ed., National Bureau of Standards, Washington, D.C., 1982.Google Scholar
  5. 5.
    J.C. Malas, J.T. Morgan, H.L. Gegel, J.S. Gunasekera, S.M. Doraivelu, and S.I. Oh, “An Investigation on the Mathematical Modeling Technique used for Analyzing Industrial Metal-working Processes,” in11th North American Manufacturing Research Conference Proceedings, North American Manufacturing Research Institute of SME, Dearborn, Michigan, 1983, pp. 203–210.Google Scholar
  6. 6.
    J.S. Gunasekera and S. Hoshino, “Extrusion of Non-Circular Sections through Shaped Dies,”Annals Intl. Inst. Prod. Eng. Res. (C1RP) 29, p. 141, 1980.Google Scholar
  7. 7.
    V. Nagpal and T. Altan, “Computer-Aided Design and Manufacturing of Dies for Lubricated Extrusion of Shapes,”J. Mech. Working Tech. 1, 183, 1978.CrossRefGoogle Scholar

Copyright information

© Springer-Verlag New York Inc 1990

Authors and Affiliations

  • R. Srinivasan
    • 1
  • J. S. Gunasekera
    • 2
  • H. L. Gegel
    • 3
  • S. M. Doraivelu
    • 3
  1. 1.Wright State UniversityDaytonUSA
  2. 2.Ohio UniversityAthensUSA
  3. 3.Universal Energy SystemsDaytonUSA

Personalised recommendations