Skip to main content
SpringerLink
Log in

Measurement and prediction of plastic anisotropy in deep-drawing steels

  • Published:
Metallurgical Transactions A Aims and scope Submit manuscript

Abstract

R-values and yield stresses were measured as a function of inclination with respect to the rolling direction on 15 steels selected from four basic types [high-strength low-alloy (HSLA), Al-killed drawing quality (AKDQ), interstitial-free (IF), and rimmed]. Orientation distribution functions (ODF’s) were also determined for these steels, using both X-ray and neutron diffraction techniques. The series expansion method was employed for predicting the plastic anisotropy of the rolled sheets. Comparison with the experimental measurements indicates that the “pancake” relaxed constraint model is a more accurate predictor of behavior than the Taylor, Sachs-Kochendörfer, or two other relaxed constraint models. The best quantitative agreement is obtained when the critical resolved shear stress (CRSS) ratio for glide on the {112} (111) and {110} (111) slip systems (t112/t110) is 0.95. A “lath” relaxed constraint model (with έ23 relaxed), associated with the same CRSS ratio, leads to good results for steels with elongated microstructures.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. H.J. Bunge, M. Schulze, and D. Grzesik:Peine/Salzgitter Berichte, Sonderheft, Denmark, 1980.

    Google Scholar 

  2. F. Royer, J.M. Mohr, C. Tavard, and P. Parnière:Mém. Sci. Rev. Métall., 1977, vol. 74, pp. 449–55.

    CAS  Google Scholar 

  3. P. Van Houtte: in7th Int. Conf. on Textures of Materials, Netherlands Society for Materials Science, Zwijndrecht, Belgium, 1984, pp. 7–23.

    Google Scholar 

  4. F. Barlat:Mater. Sci. Eng., 1987, vol. 91, pp. 55–72.

    Article  CAS  Google Scholar 

  5. J.W. Christian:Metall. Trans. A, 1983, vol. 14A, pp. 1237–56.

    CAS  Google Scholar 

  6. F. Royer, C. Tavard, and P. Penning:J. Appl. Crystallogr., 1979, vol. 12, pp. 436–41.

    Article  CAS  Google Scholar 

  7. P. Gilormini, B. Bacroix, and J.J. Jonas:Acta Metall., 1988, vol. 36, pp. 231–56.

    Article  CAS  Google Scholar 

  8. P. Franciosi:Acta Metall., 1983, vol. 31, pp. 1331–42.

    Article  CAS  Google Scholar 

  9. P. Van Houtte: in5th Int. Conf. on Textures of Materials, Aachen, Federal Republic of Germany, G. Gottstein and K. Lücke, eds., Springer, Berlin, 1978, vol. II, pp. 347–56.

    Google Scholar 

  10. G.Y. Chin:Metall. Trans., 1972, vol. 3, pp. 2213–16.

    Article  CAS  Google Scholar 

  11. B. Orlans-Joliet, J.H. Driver, and F. Montheillet:Acta Metall., 1990, in press.

  12. Ph. Lequeu, P. Gilormini, F. Montheillet, B. Bacroix, and J.J. Jonas:Acta Metall., 1986, vol. 34, pp. 439–51.

    Google Scholar 

  13. G.I. Taylor:J. Inst. Met., 1938, vol. 62, pp. 307–24.

    Google Scholar 

  14. P. Van Houtte:Textures Microstruct., 1988, vol. 8-9, pp. 313–50.

    Article  Google Scholar 

  15. H.J. Bunge:Texture Analysis in Material Science, Butterworth’s, London, 1982.

    Google Scholar 

  16. H.J. Bunge:Krist. Tech., 1970, vol. 5, pp. 145–75.

    Article  CAS  Google Scholar 

  17. G. Sachs:Z. Ver. Dtsch. Ing., 1928, vol. 72, pp. 734–36.

    Google Scholar 

  18. A. Kochendörfer:Reine und Angewandte Metallkde., Springer, Berlin, 1941.

    Google Scholar 

  19. F. Royer: Thèse de Doctorat d’État, Université de Metz, Metz, France, 1986.

    Google Scholar 

  20. C. Tomé, G.R. Canova, U.F. Kocks, N. Christodoulou, and J.J. Jonas:Acta Metall., 1984, vol. 32, pp. 1637–53.

    Article  Google Scholar 

  21. G.R. Canova: Thèse de Doctorat d’État, Université de Metz, Metz, France, 1986.

    Google Scholar 

  22. U.F. Kocks and G.R. Canova: inDeformation of Polycrystals: Mechanisms and Microstructures, 2nd Risϕ Int. Symp., N. Hansen, A. Horsewell, T. Leffers, and H. Lilholt, eds., Risϕ National Laboratory, Roskilde, Denmark, 1981, pp. 35–44.

    Google Scholar 

  23. Ph. Lequeu and J.J. Jonas:Metall. Trans. A, 1988, vol. 19A, pp. 105–20.

    CAS  Google Scholar 

  24. K. Sakata, D. Daniel, and J.J. Jonas:Textures Microstruct., 1989, vol. 11, pp. 41–56.

    Google Scholar 

  25. D. Daniel, K. Sakata, J.J. Jonas, I. Makarow, and J.F. Bussière: inSymp. on Nondestructive Monitoring of Material Properties, MRS Fall Meeting, Boston, MA, 1988, in press.

    Google Scholar 

  26. P. Van Houtte:Textures Microstruct., 1987, vol. 7, pp. 29–72.

    Google Scholar 

  27. C. Esling, F. Wagner, and H.J. Bunge: inQuantitative Texture Analysis, H.J. Bunge and C. Esling, eds., Deutsche Gesellschaft fur Metallkunde, Oberursel, Federal Republic of Germany, 1982, pp. 319–42.

    Google Scholar 

  28. F. Royer, J.M. Mohr, and C. Tavard:C. R. Acad. Sci. Paris Série B, 1975, vol. 281, pp. 555–58.

    Google Scholar 

  29. H.J. Bunge: in8th Int. Conf. on Textures of Materials, Santa Fe, NM, J.S. Kallend and G. Gottstein, eds., AIME, Warrendale, PA, 1988, pp. 69–78.

    Google Scholar 

  30. F. Emren, U. Von Schlippenbach, and K. Lücke:Acta Metall., 1986, vol. 34, pp. 2105–17.

    Article  CAS  Google Scholar 

  31. H. Alworth: USS Research, NADDRG, private communication, 1988.

  32. Hsun Hu:Metall. Trans. A, 1983, vol. 14A, pp. 1521–23.

    CAS  Google Scholar 

  33. R.P. Arthey and W.B. Hutchinson:Metall. Trans. A, 1981, vol. 12A, pp. 1817–22.

    Google Scholar 

  34. Y.C. Liu:Metall. Trans. A, 1983, vol. 14A, pp. 1199–1205.

    Google Scholar 

  35. J.S.H. Lake, D.J. Willis, and H.G. Fleming:Metall. Trans. A, 1988, vol. 19A, pp. 2805–17.

    CAS  Google Scholar 

  36. A.N. Bramley and P.B. Mellor:Int. J. Mech. Sci., 1966, vol. 8, pp. 101–14.

    Article  Google Scholar 

  37. R. Penelle: in5th Int. Conf. on Textures of Materials, Aachen, Federal Republic of Germany, G. Gottstein and K. Lücke, eds., Springer, Berlin, 1978, vol. II, pp. 129–53.

    Google Scholar 

  38. S.L. Semiatin, P.R. Morris, and H.R. Piehler:Texture Cryst. Solids, 1979, vol. 3, pp. 191–214.

    CAS  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Metallurgical Engineering, McGill University, H3A 2A7, Montreal, PQ, Canada

    D. Daniel (Graduate Student) & J. J. Jonas (Professor of Steel Processing)

Authors
  1. D. Daniel
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. J. J. Jonas
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Daniel, D., Jonas, J.J. Measurement and prediction of plastic anisotropy in deep-drawing steels. Metall Trans A 21, 331–343 (1990). https://doi.org/10.1007/BF02782413

Download citation

  • Received:

  • Issue Date:

  • DOI: https://doi.org/10.1007/BF02782413

Keywords

Search

Navigation