Abstract
Dry and wet chemical etching of epitaxial In0, 5Ga0.5P layers grown on GaAs substrates by gas-source molecular beam epitaxy have been investigated. For chlorine-based dry etch mixtures (PCl3/Ar or CC12F2/Ar) the etching rate of InGaP increases linearly with dc self-bias on the sample, whereas CH4/H2-based mixtures produce slower etch rates. Selectivities of ≥500 for etching GaAs over InGaP are obtained under low bias conditions with PCl3/Ar, but the surface morphologies of InGaP are rough. Both CC12F2/Ar and CH4/H2/Ar mixtures produce smooth surface morphologies and good (≥10) selectivities for etching GaAs over InGaP. The wet chemical etching rates of InGaP in H3PO4:HC1:H2O mixtures has been systemically measured as a function of etch formulation and are most rapid (∼1 μn · min−1) for high HCl compositions. The etch rate,R, in a 1:1:1 mixture is thermally activated of the formR ∝ \(e^{ - E_a /kT} \), whereE a = 11.25 kCal · mole−1. This is consistent with the etching being reaction-limited at the surface. This etch mixture is selective for InGaP over GaAs.
Similar content being viewed by others
References
D. Biswas, N. Debbar, P. Bhattacharya, M. Razeghi, M. De- four and F. Omnes, Appl. Phys. Lett.56, 833 (1990).
J. M. Oison, R. K. Ahrenkiel, D. J. Dunlavy, B. M. Keyes and A. E. Kibler, Appl. Phys. Lett.55, 1208 (1990).
R. A. Ahrenkiel, J. M. Oison, D. J. Dunlavy, B. M. Keyes and A. E. Kibbler, J. Vac. Sci. Technol.A8, 2002 (1990).
C. P. Kuo, S. K. Vong, R. M. Cohen and G. B. Stringfellow, J. Appl. Phys.57, 5428 (1985).
Y. K. Su, M. C. Wu, C. Y. Chang and K. Y. Cheng, J. Cryst. Growth76, 299 (1986).
J. M. Dallesasse, I. Szafranek, J. N. Baillurgeon, N. Al-Zein, N. Holonyak, Jr., G. E. Stillman and K. Y. Cheng, J. Appl. Phys.68, 5866 (1990).
K. Kobayashi, I. Hino, A. Gomyo, S. Kawata and T. Suzuki, IEEE J. Quantum Electron.23, 704 (1987).
J. H. Quigley, M. J. Hafich, H. Y. Lee, R. E. Stare and G. Y. Robinson, J. Vac. Sci. Technol.B7, 358 (1989).
D. W. Nain, D. G. Deppe, N. Holonyak, Jr., R. M. Fletcher, C. D. Kuo, T. D. Osentowski and M. G. Craford, Appl. Phys. Lett.52, 1329 (1988).
S. Kawata, H. Fuji, K. Kobayashi, A. Gomyo, I. Hino and T. Suzuki, Electron. Lett.23, 1327 (1987).
J. M. Kuo, Y. K. Chen, M. C. Wu and M. A. Chin, Appl. Phys. Lett, (in press).
S. J. Pearton, J. M. Kuo, F. Ren, A. Katz and A. Perley, Appl. Phys. Lett.59, 1467 (1991).
F. Ren, J. M. Kuo, S. J. Pearton, T. R. Fullowan and J. R. Lothian, J. Electron. Mater, (in press).
J. M. Kuo and E. A. Fitzgerald (unpublished).
S. J. Pearton, T. Nakano and R. A. Gottscho, J. Appl. Phys.69, 4206 (1991).
See for example, R. H. Burton, R. A. Gottscho and G. Smo- linsky, Ch. 3 in Dry Etching for Microelectronics, ed. R. A. Powell (North-Holland, Amsterdam, 1984).
See, for example, VLSI Fabrication Principles, S. K. Ghandi (Wiley, NY, 1983).
Electronic Materials Science and Technology, S. P. Murarka and M. C. Peckerar (Academic Press, NY 1989), Ch. 10.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Lothian, J.R., Kuo, J.M., Ren, F. et al. Plasma and wet chemical etching of In0.5Ga0.5P. J. Electron. Mater. 21, 441–445 (1992). https://doi.org/10.1007/BF02660409
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF02660409