Skip to main content
SpringerLink
Log in

Technical note: A new test procedure for the bending under tension friction test

  • Published:
Journal of Materials Engineering and Performance Aims and scope Submit manuscript

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

References

  1. D.W. Vallance and D.K. Matlock, “Application of the Bending Under Tension Friction Test to Coated Sheet Steels,”J. Mat. Eng. Perform., 1(4), 685–693 (1992).

    Article  CAS  Google Scholar 

  2. A.K. Ghosh, “A Method for Determining the Coefficient of Friction in Punch Stretching of Sheet Metals,”Int. J. Mech. Sci., 19, 457 (1977).

    Article  Google Scholar 

  3. A.J. Ranta-Eskola, J. Kumpulainen, and M. Sulonen, “Comparison of Strip Drawing Tests Used for Measuring Surface Interac-tions in Press Forming,”Proc. of 12th Cong., IDDRG, S. Margherita Ligure, Italy, 165–174 (1982).

    Google Scholar 

  4. J.L. Duncan, B.S. Shabel and J. Gerbase Filho, “A Tensile Strip Test for Evaluating Friction in Sheet Metal Forming,” SAE Paper No. 780391 (1978).

  5. E. Schedin, K. Fredriksson, and C. Gustafsson, “Characterization of Friction Properties During Sheet Forming,” Proc. of 15th Cong., International Deep Drawing Research Group, Dearborn, Michigan, ASM International, Materials Park, Ohio, 55–61 (1988).

    Google Scholar 

  6. H.D. Nine, “Drawbead Forces in Sheet Metal Forming,”Mechanics of Sheet Metal Forming, D.P. Koistinen and N.M. Wang, Ed., Plenum Press, New York, 179 (1978).

    Chapter  Google Scholar 

  7. R. Pearce, “Some Effects of Friction in Punch-Stretching,”Developments in the Drawing of Metals, The Metals Society, London, 249 (1983).

    Google Scholar 

  8. M. Sulonen, P. Eskola, J. Kumpulainen, and A. Ranta-Eskola, “A Reliable Method for Measuring the Friction Coefficient in Sheet Metal Forming,“ International Deep Drawing Research Group, Working Group Meetings, Paper WG III/4, Tokyo (1981).

  9. R.T. Fox, A.M. Maniatty, and D. Lee, “Determination of Friction Coefficient for Sheet Materials Under Stretch-Forming Conditions,”Metall. Trans. A, 20, 2179–2182 (1989).

    Article  Google Scholar 

  10. D.W. Vallance, “Analysis of Friction Behavior of Coated Sheet Steel Using the Bending Under Tension Test,” M.S. thesis No. T-3796, Colorado School of Mines, Golden, CO (1990). U.V. Rangarajan, D.K. Matlock, and G. Krauss, “The Effect of Coating Properties on the Frictional Response of Zinc-Coated Sheet Steels,”Zinc-Based Steel Coating Systems: Metallurgy and Performance, G. Krauss and D.K. Matlock, Ed., The Metals Society, Warrendale, 263–280 (1990).

  11. R.G. Davies and W.S. Stewart, “Influence of Die Material upon the Coefficient of Friction of Zinc Coated Steels,”Zinc-Based Steel Coating Systems: Metallurgy and Performance, G. Krauss and D.K. Matlock, Ed., The Metals Society, Warrendale, 243–250 (1990).

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Advanced Steel Processing and Products Research Center, Colorado School of Mines, Golden, Colorado

    G. J. Wenzloff, T. A. Hylton & D. K. Mattock

Authors
  1. G. J. Wenzloff
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. T. A. Hylton
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. D. K. Mattock
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Wenzloff, G.J., Hylton, T.A. & Mattock, D.K. Technical note: A new test procedure for the bending under tension friction test. JMEP 1, 609–613 (1992). https://doi.org/10.1007/BF02649242

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/BF02649242

Keywords

Search

Navigation