Abstract
The influence of manganese and iron additions on the recrystallization behavior of a hot-rolled Al-Mg-Si-Cu alloy has been investigated. In the as-cast ingot, some manganese remains in supersaturated solid solution and, during the preheating step, precipitates as fine (0.1 to 0.3 μm) dispersoidsα- Al12Mn3Si and α(AlFeMnSi), depending on the local iron content. The presence of the dispersoids increases the alloy’s resistance to recrystallization. The remaining manganese along with iron forms coarse (30 to 100 μm) α(AlFeMnSi) phases in the interdendritic channels upon solidification. During rolling, these coarse phases are broken up and the matrix surrounding the phases is highly strained. The highly strained regions around the precipitates are preferential sites for the nucleation and growth of new, strain-free, recrystallized grains. Decreasing the iron content decreases the amount of coarse α(AlFeMnSi) constituent phase and increases the recrystallization resistance of the alloy for a given concentration of manganese. For iron-free alloys, coarse α-Al12Mn3Si phase forms during solidification. The increased recrystallization resistance is attributed to the lower probability for particle-stimulated recrystallization. Increasing the manganese content beyond what is normally found in 6013 increases the volume fraction of both the dispersoids and the coarse constituent phases. However, the increased volume fraction of the dispersoids in the iron-containing alloys more than compensates for the increase in volume fraction of coarse constituent particles, resulting in an increase in the recrystallization resistance with increased manganese content. In this research, alloys containing varying amounts of manganese and iron with levels of magnesium, silicon, and copper consistent with the nominal composition of 6013 were hot deformed and solution heat treated to produce microstructures ranging from fully recrystallized to unrecrystallized.
Similar content being viewed by others
References
Bom K. Park: U.S. Patent 4,589,932.
I.J. Polmear:Light Alloys, Metallurgy of Light Metals, Edward Arnold Publishing, Baltimore, MD, 1981.
M. Cooper and K. Robinson:Acta Cryst., 1966, vol. 20, p. 614.
N. Raghunathan and T. Sheppard:Mater. Sci. Technol, 1988, May, pp. 268–80.
F.J. Humphreys:Met. Sci., 1979, Mar–Apr., pp. 136–45.
E. Nes:Recrystallization and Grain Growth of Multi Phase Particle Containing Materials, Riso National Laboratory, Roskilde, Denmark, 1980, pp. 85–93 and 281–89.
F.J. Humphreys and P.N. Kalu:Annealing Processes: Recovery, Rectystallization, and Grain Growth, Risø National Laboratory, Roskilde, Denmark, 1986, pp. 385–90.
F.J. Humphreys:Acta Metall., 1979, vol. 25, p. 1323.
C.S. Smith:Trans. TMS-AIME, 1948.
E.E. Underwood:Quantitative Stereology, Addison-Wesley, Reading, MA, 1970.
K. Ranganathan: Ph.D. Thesis, Georgia Institute of Technology, Atlanta, GA, 1991.
B. Thanaboonsombut: Ph.D. Thesis, Georgia Institute of Technology, Atlanta, GA, January, 1994.
Anne Lise Dons:Z. Metallkd., 1991, vol. 82, pp. 684–88.
Y. Langsrud:International Workshop on the Effect of Iron and Silicon in Aluminum and Its Alloys, Balatonfur, Hungary, May 22–28, 1989.
L.F. Mondolfo:Aluminum Alloys: Structure and Properties, 1st ed., Butterworth and Co., London, 1976.
Homogenization and Annealing of Aluminum and Copper Alloys, E.H. Chia, J. Crane, and H.D. Merchant, eds., TMS, Warrendale, PA, 1988, pp. 1–52.
P.N. Anyalebechi, T.N. Rounds, and R.E. Sanders, Jr.:Light Metals 1991, Elwin L. Rooy, ed., TMS, Warrendale, PA, 1990.
M. Cooper:Acta Cryst., 1967, vol. 23, p. 1106.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Jeniski, R.A., Thanaboonsombut, B. & Sanders, T.H. The effect of iron and manganese on the recrystallization behavior of hotrolled and solution-heat-treated aluminum alloy 6013. Metall Mater Trans A 27, 19–27 (1996). https://doi.org/10.1007/BF02647743
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF02647743