Abstract
A double-disk (DD) process was developed in this study for producing highly elongated flakes which are very promising for application as a filler for conductive composites with a plastic matrix. The Al-12Si alloy was selected as the experimental alloy in view of its high stiffness, strength, and integrity which are beneficial for retaining its high aspect ratio during the fabrication of the composites. Various operational parameters,i.e., pouring temperature and the rotational speeds of upper disk and quenching disk, were monitored in the powder production to reveal their effects on the size distribution and morphology of flakes. The flake formation mechanism was also investigated. Experimental results indicate that the broad size distribution of the flakes produced by the double-disk process rises from the splat-quenching effect and the formation of interlinked flakes and whisker-shaped flakes. The mean particle size (or mean flake width) increases with a decreasing rotational speed of centrifugal disk or quenching disk speed, but is little influenced by pouring temperature. The length-to-width ratio of flakes varies with the rotational speed of quenching disk but inversely with pouring temperature, centrifugal disk speed, and flake width. The thickness varies inversely with all of these variables. The aspect ratio varies with pouring temperature, rotational speed of quenching disk, and flake width, but varies inversely with centrifugal disk speed. All of these variations might be accounted for by considering the solidification rate and dragging rate. Based on these two rates, theoretical relationships for length-to-width ratio, thickness, and aspect ratio as a function of various metallurgical factors are derived and correlate sufficiently with the trends of experimental data.
Similar content being viewed by others
References
J.E. Hatch:Aluminum: Properties and Physical Metallurgy, ASM, Metals Park, OH, 1984, pp. 382–84.
H. Nishimura:J. Jpn. lnst. Light Met., 1984, vol. 34, pp. 115–31.
H. Jones and M.H. Burden:J. Phys. E, 1971, vol. 4, pp. 671–74.
A.L. Holbrook:Int. J. Powder Metall., 1986, vol. 22, pp. 39–45.
I.G. Palmer, R.E. Lewis, and D.D. Crooks:Rapid Solidification Processing—Principles and Technologies, II, R. Mehrabian, B.H. Kear, and M. Cohen, eds., Claitor's Publishing Division, Baton Rouge, LA, 1980, pp. 342–53.
R.A. Crossman:Polymer Eng. Sci., 1985, vol. 25 (8), pp. 507–13.
J.M. Wentzell:Powder Metall. Int., 1986, vol. 18, p. 16.
G. Lang, P. Laty, J.-C. Joud, and P. Desre:Z. Metallkd., 1977, vol. 68, pp. 113–16.
R.E. Maringer:Mater. Sci. Eng., 1988, vol. 98, pp. 13–20.
H. Jones:J. Phys. D, 1971, vol. 4, pp. 1657–60.
J. Madejski:Int. J. Heat Mass Transfer, 1976, vol. 19, pp. 1009–13.
G. Schluckebierand and B. Predel:Z. Metallkd., 1982, vol. 73, pp. 103–10.
H.H. Liebermann and R.L. Bye, Jr.:Rapidly Solidified Crystalline Alloys, S.K. Das, B.H. Kear, and CM. Adam, eds., TMS-AIME, Warrendale, PA, 1985, pp. 61–76.
H. Jones:Ultrarapid Quenching of Liquid Alloys, H. Herman, ed., Academic Press, Inc., New York, NY, 1981, pp. 1–72.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Shue, KY., Yeh, JW. The characterization of the A1-12 Wt Pct Si flake powder produced by a double-disk process. Metall Mater Trans A 26, 1571–1581 (1995). https://doi.org/10.1007/BF02647607
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF02647607