Abstract
A technique for the calculation of the elastic modulus of Ti:6Al-4V sheet based upon pole figure data and single crystal elastic constants has been developed. The technique uses pole figures based upon the Lopata and Kula method, the Schmid and Boas approximation for Youngs modulus, and uses a Reuss averaging technique. Comparison of the resultant values to experimentally determined modulus have shown excellent agreement. Examples of the technique to the evaluation of various lots of commercial sheet material are presented.
Similar content being viewed by others
References
W. A. Backofen,et al.:ASM Trans., 1962, vol. 50, p. 264.
D. Lee and W. A. Backofen:Trans. TMS-AIME, 1966, vol. 236, p. 1696.
W. F. Hosford, Jr.:Metals Engr. Quart., 1966, vol. 6, p. 13.
A. J. Hatch:Trans. TMS-AIME, 1965, vol. 233, p. 44.
A. Zarkades and F. R. Larson: Tech. Rep. Ammrl. Tr 67-05, U.S. Army, Mater, and Mech. Research Center, Dec. 1967.
W. Voigt:Lehrbuch der Krktallphysik, Leipzig, Teubner Verlag, 1928.
A. Reuss:Z. Angew. Math. Mech., 1929, vol. 9, p. 49.
R. Hill:Proc. Phys. Soc., 1952, vol. A52, p. 349.
E. Kroner:Z. Phys., 1958, vol. 151, p. 504.
H. J. Bunge and W. T. Roberts:J. Appl. Cryst., 1969, vol. 2, p. 116.
P. R. Morris:Int. J. Eng. Sci., 1970, vol. 8, p. 49.
E. Schmid and W. Boas:Plasticity of Crystals, F. A. Hughes and Co., Ltd., London, 1950.
J. W. Flowers, Jr., K. C. O’Brien, and P. C. McEleney:J. Less Common Metals, 1964, vol. 7, p. 393.
F. R. Larson: Tech. Rep. AMRA/TR65-24, U.S. Army Mater. Res. Agency, 1965.
P. R. Morris and A. J. Heckler: inAdvances In X-Ray Analysis, vol. 11, J. B. Newkirk, G. R. Mallet, and H. G. Pfeiffer, eds., Plenum Press, New York, 1968.
R. Roe:J. Appl. Phys., 1959, vol. 30, p. 850.
H. J. Bunge:Krist. Tech., 1968, vol. 3, p. 431.
S. L. Lopata and E. B. Kula:Trans. TMS-AIME, 1962, vol. 224, p. 865.
R. H. Olsen: Boeing Document D6-25265, 1970, alsoMetallogr., 1972, vol. 5, pp. 369–71.
F. L. Parkinson: Unpublished Research, The Boeing Company, 1971.
J. S. Kallend and G. J. Davies:J. Inst. Metals, 1970, vol. 98, p. 242.
Metallic Materials and Elements for Aerospace Vehicle Structures, MIL Handbook 5A, Feb. 1966, p. 607.
Author information
Authors and Affiliations
Additional information
Formerly with the Boeing Company, Seattle Wash.
Rights and permissions
About this article
Cite this article
Olsen, R.H., Moreen, H.A. Calculation of the elastic anisotropy of Ti:6Al-4V alloy sheet from pole figure data. Metall Trans 4, 701–705 (1973). https://doi.org/10.1007/BF02643078
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF02643078