Advertisement

Experimental Mechanics

, Volume 45, Issue 2, pp 137–143 | Cite as

Characterization of a new luminescent photoelastic coating

  • J. Hubner
  • L. Chen
  • Y. Liu
  • K. Schanze
  • P. Ifju
  • J. Nicolosi
  • W. El-Ratal
Article

Abstract

The luminescent photoelastic coating (LPC) technique measures the full-field shear strain and its principal direction on the surface of complex three-dimensional components. The measured optical strain response is also dependent on the coating thickness. Achieving uniform coating thickness is difficult, and thus requires thickness correction for accurate quantitative strain measurements. The original formulations of LPC employed a dual-layer coating containing luminescent dyes to transmit both strain and thickness information. This paper will document (theory and experiment) a new strategy: a single-layer coating that incorporates both a luminescent dye and an absorption dye. Dependent on the concentration of the absorption and luminescent dyes, the solution is sprayed onto the object of interest to a minimum threshold thickness that corresponds to a predefined penetration depth. Advantages of the single-layer coating are the elimination of thickness dependency, the elimination of compliance and adhesion issues between multiple layers, simpler data acquisition and post-processing methods, and easier and faster coating preparation and application.

Key Words

Luminescent photoelastic coating photoelasticity strain digital imaging 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Hubner, J.P., Ifju, P.G., Schanze, K.S., Liu, Y., Chen, L., andEl-Ratal, W., “Luminescent Photoelastic Coatings,” EXPERIMENTAL MECHANICS,44 (4),416–424 (2004).Google Scholar
  2. 2.
    Hubner, J.P., Ifju, P.G., Schanze, K.S., Jaing, S., Liu, Y., andEl-Ratal, W., “Luminescent Strain Sensitive Coatings,”AIAA Journal,42 (8),1662–1668 (2004).CrossRefGoogle Scholar
  3. 3.
    Zandman, F., Redner, S., andDally, J.W., Photoelastic Coatings, Iowa State University Press, Ames (1977).Google Scholar
  4. 4.
    Hubner, J., Nicolosi, J., Chen, L., Ifju, P., and El-Ratal, W., “Oblique Incidence Response of Photoelastic Coatings,” SEM X International Congress and Exposition on Experimental and Applied Mechanics, Costa Mesa, CA, June, Paper 193 (2004).Google Scholar
  5. 5.
    Alberty, R.A., Physical Chemistry, 7th edition, Wiley, New York, 535–539 (1987).Google Scholar
  6. 6.
    Lesniak, J.R. and Zickel, M.J., “Applications of Automated Grey-field Polariscope,” Proceedings of Society of Experimental Mechanics Spring Conference, Houston, TX, June, 298–301 (1998).Google Scholar
  7. 7.
    ASTM D 3359: Standard Test Methods for Measuring Adhesion by Tape Test, Annual Book of ASTM Standards, Vol. 06.01, ASTM, West Conshohocken, PA, 370–376 (2001).Google Scholar

Copyright information

© Society for Experimental Mechanics 2005

Authors and Affiliations

  • J. Hubner
    • 1
  • L. Chen
    • 1
  • Y. Liu
    • 2
  • K. Schanze
    • 2
  • P. Ifju
    • 1
  • J. Nicolosi
    • 1
  • W. El-Ratal
    • 3
  1. 1.Department of Mechanical and Aerospace EngineeringUniversity of FloridaGainesvilleUSA
  2. 2.Department of ChemistryUniversity of FloridaGainesvilleUSA
  3. 3.Chassis Division, DSEVisteon CorporationSterling HeightsUSA

Personalised recommendations