Abstract
We present details of a dual-actuator rig developed for testing rectangular plates supported on three sides, with the remaining (longitudinal) edge free, under combined uniaxial compression and in-plane bending. Particular attention is given to ensuring a constant strain gradient at the loaded ends, as opposed to a constant load eccentricity, in order to determine the post-buckling behavior and ultimate load and moment capacities of unstiffened thin-walled elements. Strain gradients varying from pure compression to pure bending are facilitated. Attention is also given to ensuring simply supported boundary conditions, and the methods used for anchoring the tensile stresses that develop at the loaded edges as a result of large plate deflections. Details of the methods for controlling the applied displacements are given, for which a system of four laser displacement devices was employed in order to achieve the required strain gradient. The operation of the rig is verified against established theoretical solutions.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Kalyanaraman, V., Pekoz, T. andWinter, G., “Unstiffened Compression Elements,”Journal of the Structural Division, ASCE,103 (ST9),1833–1848 (1977).
Winter, G., “Strenth of Thin Steel Compression Flanges,”Transactions of the ASCE,112,527–567 (1947).
Winter, G., Commentary on the 1968 Edition of the Specification for the Design of Cold-formed Steel Structural Members,American Iron and Steel Institute, New York (1970).
Desmond, T.P., Pekoz, T. andWinter, G., “Edge Stiffeners for Thin-walled Members,”Journal of the Structural Division ASCE,107 (ST2),329–353 (1981).
Rhodes, J., “Buckling of Thin Plates and Thin-plate Members,”Structural Failure and Plasticity, IMPLAST, 2000, 21–42 (2000).
Rhodes, J., Harvey, J.M. andFok, W.C., “The Load-carrying Capacity of Initially Imperfect Eccentrically Loaded Plates,”International Journal of Mechanical Sciences,17,161–175 (1975).
American Iron and Steel Institute, North American Specification for the Design of Cold-formed Steel Structural Members, 2000 edition, Washington D.C. (2000).
AS/NZS 4600, Australian/New Zealand Standard, Cold-formed Steel Structures, 1996 edition, Sydney (1996).
Rasmussen, K.J.R., “Design of Thin-walled Columns with Unstiffened Flanges,”Engineering Structures,16 (5),307–316 (1994).
Chick, C.G. andRasmussen, K.J.R., “Thin-walled Beam-columns. 2: Proportional Loading Tests,”Journal of Structural Engineering, ASCE,125 (11),1267–1276 (1999).
Moxham, K.E., Buckling Tests on Individual Welded Steel Plates in Compression, University of Cambridge, Report CUED/C-Struct/TR.3 (1971).
Bulson, P.S., The Stability of Flat Plates, Chatto and Windus, London (1970).
Bambach, M.R. and Rasmussen, K.J.R., “Residual Stress in Unstiffened Plate Specimens,” Proceedings of the 3rd International Conference on Thin-Walled Structures, Cracow, Poland (2001).
Venkataramaiah, K.R. and Roorda, J., “Analysis of Local Plate Buckling Data,” Proceedings of the 6th International Specialty Conference on Cold-formed Steel Structures (1982).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Bambach, M.R., Rasmussen, K.J.R. Experimental techniques for testing unstiffened plates in compression and bending. Experimental Mechanics 44, 91–96 (2004). https://doi.org/10.1007/BF02427982
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF02427982