Abstract
A hybrid experimental-numerical method is presented for evaluating the stresses around holes or notches in orthotropic composites. Moiré-measured displacements and hybrid finite elements are employed. The geometric discontinuity of interest is surrounded by a hybrid element, which is a subregion within the physical structure. Measured displacements provide input information at nodal locations on the external boundary of the hybrid element. Little experimental data are needed, and the approach is accurate and effective. The method is demonstrated for a uniaxially loaded orthotropic laminate containing a central circular hole.
Similar content being viewed by others
References
Peterson, R.E., Stress Concentration Factors, John Wiley, New York (1974).
Lekhnitskii, S.G., “Stresses in Infinite Anisotropic Plate Weakened by Elliptical Hole,” DAN SSSR,4 (3), (1936).
Lekhnitskii, S.G., Theory of Elasticity of an Anisotropic Elastic Body, Government Publishing Houses for Technical-Theoretical Works, Moscow and Leningrad (1950).Also, P. Fern (English trans.), Holden-Day, San Francisco (1963).
Lekhnitskii, S.G., Anisotropic Plates, S.W. Tsai and T. Cheron (English trans.), Gordon and Breach, New York (1968).
Savin, G.N., Stress Distribution around Holes, Naukova Dumka Press, Kiev (1968).Also, NASA 77 F-601 (November 1970).
Rowlands, R.E., Daniel, I.M. andWhiteside, J.B., “Stress and Failure Analysis of a Glass-epoxy Composite Plate with a Circular Hole,” EXPERIMENTAL MECHANICS,13 (1),31–37 (September1973).
Rowlands, R.E., Daniel, I.M. and Whiteside, J.B., “Geometric and Loading Effects on Strength of Composite Plates with Cutouts,” Composite Materials, Testing and Design (Third Conference), ASTM STP546, American Society for Testing and Materials, 361–375 (1974).
Daniel, I.M., Rowlands, R.E. andPost, D., “Moiré Methods for Strain Analysis of Composites,” EXPERIMENTAL MECHANICS,13 (6),246–252 (June1973).
Whiteside, J.B., Daniel, I.M. andRowlands, R.E., “The Behavior of Advanced Filamentary Composite Plates with Cutouts,”U.S. Air Force Tech. Report AFFDL-TR-73-48, Wright-Patterson Air Force Base, OH (1973).
Gerhardt, T.D., “A Hybrid/Finite Element Approach for Stress Analysis of Notched Anisotropic Materials,”ASME J. Appl. Mech.,51,804–810 (December1984).
Gerhardt, T.D., “Strength and Stiffness Analysis of Notched, Green Oak Pallet Stringers,”Res Paper FPL 452, USDA For. Serv. For. Prod. Lab., Madison, WI (1984).
Zalph, B.L., “Predicting the Strength of Notched Wood Beams,” PhD thesis, Wood Science and Forest Products, Virginia Polytechnic Institute and State University (June 1989).
Foliente, G.C. andMcLain, T.E., “Strength of End-notched Wood Beams: A Critical Fillet Hoop Stress Approach,”Wood Fiber Sci.,24 (2),163–180 (1992).
Zalph, B.L. andMcLain, T.E., “Strength of Wood Beams with Filleted Interior Notches: A New Model,”Wood Fiber Sci.,24, (2),204–215 (1992).
Foliente, G.C. andMcLain, T.E., “Design of Notched Wood Beams,”J. Struct. Eng.,118 (9),2407–2420 (September1992).
Jinping, Z. andHuizu, S., “Stress Analysis around Holes in Orthotropic Plates by the Subregion Mixed Finite Element Method,”Computers and Structures,41 (1),105–108 (1991).
Tan, S.C., “Finite-width Correction Factors for Anisotropic Plate Containing a Central Opening,”J. Composite Materials,22,1080–1097 (November1988).
Tan, S.C., Stress Concentrations in Laminated Composites, Technomic Publishing Co. Inc., Lancaster, PA (1994).
Kosmodamiansky, A.C., “The Stress State of an Anisotropic Plate with Two Non-identical Holes,”Akademiia Nauk SSSR, Izvestiia, Otdelenie Tekhnicheskikh Nauk, Mechanikii Mashinostroenie,1,175–177 (1961) (in Russian).
Lin, J.K. andUeng, C.E.S., “Stresses in a Laminated Composite with Two Elliptical Holes,”Composite Structures,7,1–20 (1987).
Fan, W.X. andWu, J.G., “Stress Concentration of a Laminate Weakened by Multiple Holes,”Composite Structures,10 (4),303–319 (1988).
Feng, Z., Sanford, R.J. andRowlands, R.E., “Determining Stress Intensity Factors from Smoothing Finite-element Representation of Photomechanical Data,”Eng. Fract. Mech.,40 (3),593–601 (1991).
Feng, Z., Rowlands, R.E. andSanford, R.J., “Stress Intensity Determination by an Experimental-numerical Hybrid Technique,”J. Strain Analysis,26 (4),243–251 (1991).
He, S., “Hybrid Experimental/Numerical Analysis and Finite Element Modeling of Fracture of Aggregate Composite,” PhD thesis, Department of Engineering Mechanics and Astronautics, University of Wisconsin-Madison (May 1993).
Lin, S.T., “Quantitative Thermoelastic Stress Analysis of Orthotropic Composite Structures,” PhD thesis, Department of Engineering Mechanics, University of Wisconsin—Madison (1994).
Hawong, J.S., Lin, C.H., Lin, S.T., Rhee, J. andRowlands, R.E., “A Hybrid Method to Determine Stresses in Orthotropic Composites Using Only Isochromatic Data,”J. Composite Materials,29 (18),2366–2387 (1995).
Hong, C.S. andCrews, J.H., “Stress-concentration Factors for Finite Orthotropic Laminates with a Circular Hole and Uniaxial Loading,”NASA Tech. Paper 1469, Langley Research Center, Hampton, VA (1979).
Lin, S.T. andRowlands, R.E., “A Thermoelastic Stress Analysis of Orthotropic Composites,” EXPERIMENTAL MECHANICS,35 (3),257–265 (September1995).
Lin, S.T. and Rowlands, R.E., “Hybrid Stress Analysis,” forthcoming.
Lin, C.H., “A New Digital Isopachic Contouring Technique for Stress Analyzing Composite Materials,” PhD thesis, Department of Engineering Mechanics and Astronautics, University of Wisconsin—Madison (1994).
Freese, C.E. andBowie, O.L., “Stress Analysis of Configurations Involving Small Fillets,”J. Strain Analysis,10 (1),53–58 (1975).
Freese, C.E., “Collocation and Finite Elements—A Combined Method,”AMMRCTR 7328, Army Mater. Mech. Res. Center, Watertown, MA (June1973).
Bowie, O.L. andFreese, C.E., “Central Crack in Plane Orthotropic Rectangular Sheet,”Int. J. Fract. Mech.,8, (1),49–57 (March1972).
Bowie, O.L., “Solutions of Plane Crack Problems by Mapping Technique,”Methods of Analysis and Solutions of Crack Problems, ed. G.C. Sih, Noordhoff International Publ., Leyden (1973).
Tong, P., Pian, T.H.H. andLasry, S.J., “A Hybrid-element Approach to Crack Problems in Plane Elasticity,”Int. J. Numer. Meth. Eng.,7, (3),297–308 (1973).
Tong, P., “A Hybrid Crack Element for Rectilinear Anisotropic Material,”Int. J. Numer. Meth. Eng.,11 (2),377–382 (1977).
Hawong, J.S., Suh, J.G. and Rowlands, R.E., “Measuring Stress Intensity Factors in Orthotropic Composites Using SPATE,” Int. Meeting on Struct. Failure, Product Liability and Technical Insurance, Vienna (July 1995).
Shih (Stone), J.S., “Experimental-numerical Analysis of Bolted Joints in Finite Composites with and without Inserts,” PhD thesis, Department of Engineering Mechanics, University of Wisconsin—Madison (August 1992).
Rhee, J., “Geometric Discontinuities in Orthotropic Composites,” PhD thesis, Department of Engineering Mechanics and Astronautics, University of Wisconsin—Madison (1995).
Rhee, J. and Rowlands, R.E., “Stresses around Extremely Large or Intersecting Multiple Holes in Orthotropic Composites,” Computers and Structures, forthcoming.
Carrier, G.F., Krook, M. andPearson, C.E., Functions of a Complex Variable, McGraw-Hill Book Company, New York (1966).
Miline-Thomson, L.M., Plane Elastic Systems, Springer-Verlag, Berlin (1960).
Cook, R.D., Malkus, D.S. andPlesha, M.E., Concepts and Applications of Finite Element Analysis, 3rd ed., John Wiley, New York (1989).
Post, D., “Moiré Interferometry, Handbook on Experimental Mechanics, ed. A.S. Kobayashi, Prentice Hall, Inc., Englewood Cliffs, NJ (1987).Also, Post, D., Han, B. and Ifju, P., High Sensitivity Moiré: Experimental Analysis for Mechanics and Materials, SEM Publisher (1994).
Dally, J.W. andRead, D.T., “Electron Beam Moiré,” EXPERIMENTAL MECHANICS,33 (4),270–277 (1993).
Rowlands, R.E., Jensen, J.A. andWinters, K.D., “Differentiation along Arbitrary Orientations,” EXPERIMENTAL MECHANICS,18, (3),81–86 (March1978).
Thompson, J.C. and Negus, K.J., “Developments in a Least Squares Asymptotic Analysis of Isochromatic Data from Stress Concentration Regions in Plane Problems,” Strain, 133–134 (August 1984).
Dhillon, S.S. and Thompson, J.C., “Prediction of Stress Concentration Factors by Asymptotic Analysis of Notched Displacement Data,” Proc. Canadian Cong. Appl. Mech. (CANCAM), D26–D27 (1987).
Huang, Y.M., Rowlands, R.E. andLesniak, J.R., “Simultaneous Stress Separation, Smoothing of Measured Thermoelastic Information, and Enhanced Boundary Data,” EXPERIMENTAL MECHANICS,30, (4),398–403 (December1990).
Huang, Y.M., Lin, G.H., Suhling, J.G. andRowlands, R.E., “Determination of the Three Individual Stress from Only Measured Isochromatic Fringe Data,” EXPERIMENTAL MECHANICS,31 (4),310–319 (December1991).
Rauch, B.J. andRowlands, R.E., “Determining Reliable Edge Isopachic Data from Interior Thermoelastic Measurements,” EXPERIMENTAL MECHANICS,35 (2),174–181 (June1995).
Feng, Z. andRowlands, R.E., “Smoothing Finite-element and Experimental Hybrid Technique for Stress Analyzing Composites,”Computers and Structures,39 (6),631–639 (1991).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Rhee, J., He, S. & Rowlands, R.E. Hybrid moiré-numerical stress analysis around cutouts in loaded composites. Experimental Mechanics 36, 379–387 (1996). https://doi.org/10.1007/BF02328582
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF02328582