Abstract
This paper describes the details of a novel procedure called the cure-referencing method (CRM) to measure the strains associated with residual stresses on the surface of composite panels. The CRM involves the replication of diffraction gratings onto the surface of composite specimens during the autoclave during cycle. Residual strains associated with the curing process are measured using moiré interferometry at room temperature after the specimens have been taken out of the autoclave. The procedures for both the grating replication and the moiré interferometry experiment are described in detail. A method of high-temperature moiré interferometry was developed to resolve the residual strains due to thermal expansion from those due to chemical matrix shrinkage and stress relaxation. These procedures are demonstrated on unidirectional and multidirectional laminates and on woven textile composites.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Pagano, N.J. andHahn, H.T., “Evaluation of Composite Curing Stresses,” Composite Materials: Testing and Design (Fourth Conference), ASTM STP 617,317–329 (1977).
Agarwal, B.D. andBroutman, L.J., Analysis and Performance of Fiber Composites, 2nd ed., John Wiley & Sons, New York 71 (1990).
Mathar, J., “Determination of Initial Stress by Measuring the Deformations around Drilled Holes,”Trans. ASME,56,249 (1934).
Rendler, N.J. and Vigness, I., “Hole-drilling Strain-gage Method of Measuring Residual Stresses,” EXPERIMENTAL MECHANICS,577–586 (1966).
Bert, C.W. andThompson, G.L., “A Method for Measuring Planar Residual Stresses in Rectangularly Orthotropic Materials,”J. Composite Mat.,2,244–253 (1968).
Lee, J., Czarnek, R., and Guo, Y., “Interferometric Study of Residual Strains in Thick Composites,” Proceedings of the 1989 SEM Conference on Experimental Mechanics, Cambridge, MA, 356–364 (1989).
Gascoigne, H.E., “Residual Surface Stresses in Laminated Cross-ply Fiber-epoxy Composite Materials,” EXPERIMENTAL MECHANICS,34,27–36 (1994).
Sunderland, P., Wu, W.J. andMånson, J.E., “A Technique for the Measurement of Process-induced Internal Stresses in Polymers and Polymer Composites,”Proc. ICCM-10,3,125–132 (1995).
Lee, J. and Czarnek, R., “Measuring Residual Strains in Composite Laminates Using Moiré Interferometry,” Proceedings of the 1991 SEM Conference on Experimental Mechanics, Milwaukee, WI, 405–415 (1991).
Chapman, T.J., et al. “Prediction of Process-induced Residual Stresses in Thermoplastic Composites,”J. Composite Mat.,24,616–643 (1990).
Månson, J.E. andSeferis, J.C., “Process Simulated Laminate (PSL), A Methology to Internal Stress Characterization in Advanced Composite Materials,”J. Composite Mat.,26,405–431 (1992).
Joh, D., Byun, K.Y., andHa, J., “Thermal Residual Stresses in Thick Graphite/Epoxy Composite Laminates—Uniaxial Approach,” EXPERIMENTAL MECHANICS,33,70–76 (1993).
Hahn, H.T., “Residual Stresses in Polymer Matrix Composite Laminates,”Composite Mat.,10,265–277 (1976).
Kim, R.Y. andHahn, H.T., “Effect of Curing Stresses on the First Ply-failure in Composite Laminates,”J. Composite Mat.,13,2–16 (1979).
Unger, W.J. andHansen, J.S., “The Effect of Thermal Processing on Residual Strain Development in Unidirectional Graphite Fiber Reinforced PEEK,”J Composite Mat.,27,59–81 (1993).
Carman, G.P. andSendechyj, G.P., “Review of the Mechanics of Embedded Optical Sensors,”J. Composites Tech. Res.,17 (3),183–193 (1995).
Daniel, I.M. and Liber, T., “Effect of Laminate Constructionon Residual Stresses in Graphite/Polyimide Composites,” EXPERIMENTAL MECHANICS,21–25 (1977).
Predecki, P. andBarrett, C.S., “Stress Measurement in Graphite/Epoxy Composites by X-ray Diffraction from Fillers,”J. Composite Mat.,13,67–71 (1979).
Fenn, R.H., Jones, A.M., andWells, G.M., “X-ray Diffraction Investigation of Triaxial Residual Stresses in Composite Materials,”J. Composite Mat.,27,1338–1351 (1993).
Hyer, M.W., “Calculation of Room-temperature Shapes of Unsymmetric Laminates,”J. Composite Mat.,15,296–310 (1981).
Jeronimidls, G. andParkyn, A.T., “Residual Stresses in Carbon Fiber-thermoplastic Matrix Laminates,”J. Composite Mat.,22,401–415 (1988).
Kim, K.S., Hahn, H.T., andCroman, R.B., “The Effect of Cooling Rate on Residual Stresses in a Thermoplastic Composite,”J. Composites Tech. Res.,11 (2),47–52 (1989).
Fakuda, H., Takahashi, K., andToda, S., “Thermal Deformation of Anti-symmetric Laminates at Cure,”Proc. ICCM-10,3,141–148 (1995).
Ifju, G.P., Kilday, B.C. Niu, X., and Liu, S.C., “Residual Stress Measurements in AS4/3501-6 Laminates,” Postconference Proceedings of SEM Spring Conference on Experimental Mechanics, Bellevue, WA, 193–200 (1997).
Ifju, G.P., Kilday, B.C., Niu, X., andLiu, S.C., “A Novel Method to Measure Residual Stress in Laminated Composites,”J. Composite Mat.,33,16 (1999).
Post, D., Han, B., andIfju, P.G., High Sensitivity Moiré: Experimental Analysis for Mechanics and Materials, Springer-Verlag, New York (1994).
Whitcomb, J., Woo, K., andGundapaneni, S., “Macro Finite Element for Analysis of Textile Composites,”J. Composite Mat.,28,607–618 (1994).
Naik, R.A., Ifju, P.G., andMasters, J.E., “Effect of Fiber Architecture Parameters on the Deformation Fields and Elastic Moduli of 2-D Braided Composites,”J. Composite Mat.,28,656–681 (1994).
Hahn, H.T. andPagano, N.J., “Curing Stresses in Composite Laminates,”J. Composite Mat.,9,91–106 (1975).
White, S.R. andHahn, H.T., “Process Modeling of Composite Materials: Residual Stress Development during Cure: Part I. Model Formulation,”J. Composite Mat.,26,2402–2422 (1992).
White, S.R. andHahn, H.T., “Process Modeling of Composite Materials: Residual Stress Development during Cure: Part II. Experimental Validation,”J. Composite Mat.,26,2423–2453 (1992).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Ifju, P.G., Niu, X., Kilday, B.C. et al. Residual strain measurement in composites using the cure-referencing method. Experimental Mechanics 40, 22–30 (2000). https://doi.org/10.1007/BF02327544
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF02327544