Abstract
Electro-optic holographic interferometry was used to measure the thermally induced out-of-plane displacement field around both sides of a plated hole on a single layer, FR-4 laminate. The unique features of the electro-optic holographic interferometry technique are described as well as a method for estimating the stress in the barrel from the deflections of the pad. The pad deflections were observed to be roughly axisymmetric and were nearly the same on the front and back of the laminate. The stress was observed to increase at a more rapid rate for temperatures above the glass temperature than below and is of sufficient magnitude to cause plastic deformation in the barrel although none was observed.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
“Round Robin Reliability Evaluatnng of Small Diameter Plated Through Holes in Printed Wiring Boards,” Int. Packaging Council IPC-TR-579 (Sept. 1988).
Tossell, D.A. andAshbee, K.H.G., “High Resolution Optical Interference Investigation of Deformation due to Thermal Expansion Mismatch Around Plated Holes in Multilayer Circuit Boards,”J. Electronic Materials,18,275–286 (1989).
Davidson, D.A., “Strains in Plated Through Holes and Surface Mounted Component Solder Joints Resulting from Thermal Cycling,” Materials Developments in Microelectronic Packaging Conference Proceedings, Montreal, Quebec, ASM, 169–177 (1991).
Watt, D.W., Gross, T.S. andHening, S.D., “Three-illumination Beam Phase Shifted Holographic Interferometry Study of Thermally Induced Displacements on a Printed Wiring Board,”Appl. Opt.,30,1617–1623 (1991).
Gross, T.S., Watt, D.W., Raber, R.S., Perault, J.A. andZhang, Y., “Thermal Strain Response of Plated Holes,”Circuit World,18,21–25 (March1992).
Torres, L.A., “Thermally Induced Strain in Plated Through Holes,” IPC Tech. Paper IPC-TP-510 (1984).
Mirman, B., “Mathematical Model of a Plated Through Hole Under a Load Induced by Thermal Mismatch,”IEEE Trans. on Components, Hybrids, and Manufacturing Tech.,11,506–511 (1988).
Ianuzzelli, R.A., “Predicting Plated-Through Hole Reliability in High Temperature Manufacturing Processes,” Proc. 41st Electronic Components and Technology Conf., 410–421 (1991).
Creath, K., “Phase Shifting Speckle Interferometry,”Appl. Opt.,24,3053 (1985).
Hariharan, P., “Quasi-heterodyne Hologram Interferometry,”Opt. Eng.,24,632–638 (1985).
Raber, R.S., “Electro-optic Holographic Interferometry with Noise Tolerant Phase Unwrapping,” MS Thesis, Univ. of New Hampshire (1991).
Huntley, J., “A Noise Immune Phase Unwrapping Algorithm”Appl. Opt.,28,3268–3270 (1989).
Bone, D.W., “Fourier Fringe Analysis: The Two-dimensional Phase Unwrapping,”Appl. Opt.,25,3627–3632 (1991).
Timshenko, S. and Woinowsky-Krieger, S., Theory of Plates and Shells, McGraw-Hill (1959).
Mirman, B., personal communication (1992).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Gross, T.S., Watt, D.W. & Perault, J.A. Estimation of plated-hole barrel stress from thermally induced out-of-plane displacement gradients measured by electro-optic holographic interferometry. Experimental Mechanics 32, 316–322 (1992). https://doi.org/10.1007/BF02325584
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF02325584