Sommario
L'articolo riferisce sul comportamento elastico di accoppiamenti realizzati per forzamento di un anello di grosso spessore su di un cilindro cavo circolare retto di lunghezza finita ed in generale diversa da quella dell'elemento forzante.
La valutazione delle componenti di spostamento e di tensione presenti in ciascuno dei due elementi dell'accoppiamento è operata mediante una soluzione teorica, generale, relativa ad un cilindro cavo, circolare, retto, di lunghezza finita e sollecitato da un sistema di carichi distribuiti in modo assialsimmetrico e che è stata sviluppata in termini della funzione delle tensioni di Airy. Il metodo dei coefficienti di influenza applicato alle componenti radiale ed assiale degli spostamenti è utilizzato per la risoluzione delle equazioni, scritte in forma integrale, che governano le modalità di contatto relative alle due situazioni estreme di assenza di attrito e di adesione completa in corrispondenza delle superfici di accoppiamento.
Summary
The paper deals with the elastic behaviour of the die assemblies obtained by shrinking a thick walled ring onto a finite hollow right circular cylinder in general of different length. Displacements and stresses in the two components of the assembly are evaluated by using the theoretical general solution on the finite thick-walled hollow elastic right circular cylinder with an axially symmetrical load system in terms of Airy's stress function. Radial and axial displacement influence coefficient technique is used to solve the integral equations governing the two extreme frictionless and slipless contact modes at the mating surface.
References
Hill L.R., Cakmak A.S. andMark R., Trans. ASME E35, 729 (1968)
Motosh N., Trans. ASME B, 1097 (1974)
Venter R., Mullins M. andde Malherbe M.C., Annals of C.I.R.P.24, 147 (1975).
Matsubara S. andKudo H., Annals of C.I.R.P.,23, 53 (1974).
Lengyel B., Burns D.J. andPrasad L.V., 4th M.T.D.R. Conference, 319 (1977).
Serdengecti S. andChatfield H.B., Proc. Instn. Mech. Engrs.182, 477 (1967 – 68).
Yau W.W.F. andCakmak A.S., Int. Engng. Sci.,4, 463 (1966).
Conway H.D. andFarnham K.A., Int. Engng. Sci.,5, 541 (1967).
Conway H.D. andFarnham K.A., Int. J. Mech. Sci.,10, 757 (1968).
Bernasconi G., I Nat. Conf. AIMETA, CISM, Udine,3, 131 (1971).
Oda J., Shibahara M. andMiyamoto H., Bull. of JSME,15, 1147 (1972).
Bariani P., 5th A.I.A.S. Conference, Bari,3, (1977).
Sierakowski R.L. andSun C.T., J. of Franklin Institute,286, 99 (1968).
Shibahara M. andOda J., Bull. of JSME,11, 1000 (1968).
Kasano H., Matsumoto H. andNakahara I., Bull. of JSME,21, 7 (1978).
Steven G.P., Int. J. Engn. Sci.,15, 95 (1977).
Dagalakis N.G. andKirtley J.L., Trans. ASME, J. of Mech. Design.,100, 630 (1978).
Sawa T. andMaruyama K., Bull. of JSME,22, 420, (1979).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Bariani, P. Elastic behaviour of shrink-fitted forming die assemblies. Part I: Development of an analytical solution. Meccanica 18, 21–29 (1983). https://doi.org/10.1007/BF02156097
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF02156097