This is a preview of subscription content, log in via an institution to check access.
Literature cited
I. N. Fridlyander, Wrought Aluminum Constructional Alloys [in Russian], Metallurgiya, Moscow (1979).
R. E. Zinkham, H. Liebowitz, and D. L. Jones, “Fracture toughness-strength relationships in Al-Zn-Mg-Cu alloys,” in: Mechanical Behavior of Materials [Russian translation]. Vol. 1 (1972), pp. 370–393.
Aluminum Standards and Data, the Aluminum Association, New York (1978).
A. E. Semenov and O. A. Setyukov, “Excess intermetallide compounds in Dl alloy,” Tekhnol. Leg. Splav., No. 6, 9–11 (1972).
O. A. Setyukov, A. E. Semenov, and V. S. Zolotarevskii, “The influence of iron and silicon impurities on the phase composition and structure of V95 alloy,” Izv. Vyssh. Uchebn. Zaved., Tsvetn. Met., No. 2, 118–121 (1975).
I. N. Fridlyander, “An investigation of wrought high-strength aluminum alloys of the Al-Zn-Mg-Cu system,” in: Light Alloys [in Russian], No. 1, Izd. Akad. Nauk SSSR, Moscow (1958), P. 72.
S. N. Singh and M. C. Flemings, “Solution kinetics of a cast and wrought high strength aluminum alloy,” Trans. Met. Soc. Am. Inst. Mech. Eng.,245, No. 8, 1803–1809 (1969).
S. A. Saltykov, Stereometric Metallography [in Russian], Metallurgiya, Moscow (1976).
E. N. Starova, Yu. M. Dolzhanskii, L. I. Sibileva, et al., Treatment and Analysis of Experimental Data on the “Nairi” Computer [in Russian], Otd. Nauch.-Tekh. Inf. Vsesoyuz. Nauch.-Issled. Inst. Aviats. Mater., Moscow.
V. V. Teleshov and V. G. Kudryashov, “The structure and fracture toughness of aluminum alloys,” Fiz.-Khim. Mekh. Mater., No. 6, 7–12 (1976).
C. D. Beacham and R. M. Pelloux, “Electron fractography — a means of studying the micromechanism of failure process,” in: Applied Questions of Fracture Toughness [Russian translation] Mir, Moscow (1968).
T. A. Gordeeva and I. P. Zhegina, The Analysis of Fractures in Evaluating the Reliability of Materials [in Russian], Mashinostroenie, Moscow (1978).
M. E. Drits, A. M. Korol'kov, Yu. P. Guk, and L. P. Gerasimova, The Fracture of Aluminum Alloys Under Tensile Stresses [in Russian], Nauka, Moscow (1973).
J. P. Tanaka C. A. Pampillo, and J. R. Low, “Fractographic analysis of the low energy fracture of an aluminum alloy,” in: ASTM STP 463, Philadelphia (1970), pp. 191–215.
V. Yu. Soin, N. I. Novosil'tseva, and E. M. Morozov, “The influence of curvature of an element on crack growth rate in cyclic biaxial tension,” in: The Physics and Mechanics of Deformation and Fracture [in Russian], No. 6, Atomizdat, Moscow (1979), pp. 98–103.
S. M. El Soudani and R. M. Pelloux, “Influence of inclusion content on fatigue crack propagation in aluminum alloys,” Met. Trans.,4A, No. 2, 519–531 (1973).
A. A. Gol'denberg, L. I. Ekimenkov, and L. N. Antipova, “Intermetallides in the development of fatigue cracks in Duralumin,” Metalloved. Term. Obrab. Met., No. 2, 28–32 (1978).
G. T. Hahn and A. R. Rosenfield, “Metallurgical factors affecting fracture toughness of aluminum alloys,” Met. Trans.,6A, No. 4, 653–668 (1975).
I. N. Fridlyander, O. G. Senatorova, and T. F. Gubareva, “The kinetics of two-stage aging of V95 alloy,” Metalloved. Term. Obrab. Met., No. 6, 27–30 (1978).
S. Ya. Yarema, O. P. Ostash, V. P. Rychik, V. M. Beletskii, et al., “Fatigue crack development in sheet of D16A and V95A aluminum alloys,” Fiz.-Khim. Mekh. Mater., No. 1, 46–51 (1977).
Additional information
Translated from Fiziko-Khimicheskaya Mekhanika Materialov, Vol. 18, No. 1, pp. 3–10, January–February, 1982.
Rights and permissions
About this article
Cite this article
Fridlyander, I.N., Senatorova, O.G., Zhegina, I.P. et al. Structure, character of fracture, and properties of V95 alloy sheet in relation to impurity content. Mater Sci 18, 1–7 (1982). https://doi.org/10.1007/BF01156527
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF01156527