Nonlinear bending of toroidal shells of arbitrary transverse cross section loaded with internal pressure

  • V. V. Kuznetsov
  • S. V. Levyakov


Mathematical Modeling Mechanical Engineer Industrial Mathematic Internal Pressure Transverse Cross Section 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.


Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Literature cited

  1. 1.
    K. M. Dubyaga, “The bending of thin-walled curved tubes,” Izv. S.-Peterburgskogo Politekh. Inst.,11, No. 2 (1909).Google Scholar
  2. 2.
    Th. Karman, “Die Formänderung dünnwandiger Rohre, insbesondere federnder Ausglichrohre,” VDI-Z,55, No. 45 (1911).Google Scholar
  3. 3.
    P. G. Kafka and M. B. Dunn, “Stiffness of curved circular tubes with internal pressure,” Trans. ASME, Ser. E. J. Appl. Mech.,23, No. 2 (1956).Google Scholar
  4. 4.
    E. C. Rodabaugh and H. H. George, “Effect of internal pressure on flexibility and stress intensification factors of curved pipe or welding elbows,” Trans ASME. Ser. E. J. Appl. Mech.,79, No. 4 (1957).Google Scholar
  5. 5.
    S. H. Crandall and N. C. Dahl, “The influence of pressure on bending of curved tubes,” Proceedings of the 9th Int. Congress Appl. Mech., Bruxelles, Vol. 6 (1957).Google Scholar
  6. 6.
    L. G. Brazier, “On the flexure of thin cylindrical shells and other “thin” sections,” Proc. R. Soc. London. Ser. A,116, No. 773 (1927).Google Scholar
  7. 7.
    E. Chwalla, “Reine Biegung schlanker, dunnwandiger Rohre mit gerader Asche,” ZAMM,13, No. 1 (1933).Google Scholar
  8. 8.
    0. S. Heck, Über der Stabilität orthotroper elliptischer Zylinderschalen bei reiner Biegung,” Luftahrtforschung,14, No. 3 (1937).Google Scholar
  9. 9.
    Yu. V. Konovalov, “Bending of an infinite cylindrical shell,” Prikl. Mat. Mekh.4, No. 5, 6 (1940).Google Scholar
  10. 10.
    J. D. Wood, “Flexure of a uniformly pressurized, circular, cylindrical shell,” Trans. ASME Ser. E. J. Appl. Mech.,25, No. 4 (1958).Google Scholar
  11. 11.
    E. Reissner, “On finite bending of pressurized tubes,” Trans. ASME. Ser. E. J. Appl.Mech.,26, No. 3 (1959).Google Scholar
  12. 12.
    D. L. Kostovetskii, “Bending of curved thin-walled tubes in the region of large elastic displacements,” Izv. Akad. Nauk SSSR, OTN Mekh. Mashinostr. No. 3 (1960).Google Scholar
  13. 13.
    É.L. Aksel'rad, “Bending of thin-walled rods at large elastic displacements,” Izv. Akad. Nauk SSSR, OTN. Mekh. Mashinostr., No. 3 (1961).Google Scholar
  14. 14.
    J. T. Boyle, “Finite bending of curved pipes,” Inst. J. Solid Struct.,17, No. 5 (1981).Google Scholar
  15. 15.
    V. V. Kuznetsov and Yu. V. Soinikov, “Analysis of the deformations of shells for arbitrarydisplacements by the finite-element method,” Izv. Akad. Nauk. SSSR, MTT, No. 1 (1987).Google Scholar
  16. 16.
    S. Timoshenko, “Bending stresses in curved tubes of rectangular cross section,” Trans.ASME,45, No. 1893 (1923).Google Scholar

Copyright information

© Plenum Publishing Corporation 1994

Authors and Affiliations

  • V. V. Kuznetsov
    • 1
  • S. V. Levyakov
    • 1
  1. 1.Novosibirsk

Personalised recommendations