Skip to main content
SpringerLink
Log in

Influence of superplastic deformation on the anisotropy of 03Kh26N6T steel

  • Corrosion-Resistant Steels
  • Published:
Metal Science and Heat Treatment Aims and scope

Conclusions

  1. 1.

    The maximum difference in relative elongation parallel and transverse to the rolling direction at the optimum temperature of superplastic deformation does not completely characterize the anisotropy since it is caused by the increased sensitivity of superplastic deformation to transverse grain dimensions in these directions.

  2. 2.

    The index of anisotropy r of 03Kh26N6T steel increases with an increase in temperature and degree of strain, indicating a decrease in anisotropy of plastic properties of the steel under superplastic conditions.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

Literature cited

  1. M. V. Gradskii, Structural Superplasticity of Metals [Russian translation], Metallurgiya, Moscow (1975).

    Google Scholar 

  2. I. I. Novikov and V. K. Portnoi, Superplasticity of Alloys with Ultrafine Grain Size [in Russian], Metallurgiya, Moscow (1981).

    Google Scholar 

  3. O. M. Smirnov, Working of Metals by Pressure in the Superplastic Condition [in Russian], Mashinostroenie, Mos (1979).

    Google Scholar 

  4. A. P. Gulyaev, Superplasticity of Steel [in Russian], Metallurgiya, Moscow (1982).

    Google Scholar 

  5. A. V. Shalimova, N. I. Naumova, and A. A. Alalykin, The Superplasticity of Steels and Iron-Base Alloys: Review Information [in Russian], Chermetinformatsiya, Moscow (1988).

    Google Scholar 

  6. M. F. A. Fuad, M. A. Psepin, A. A. Lobach, and O. M. Smirnov, "Structural changes in superplastic 03Kh26N6T steel with original anisotropy," Metalloved. Term. Obrab. Met., No. 9 (1991).

  7. R. H. Brickness and J. W. Edington, "Mechanical anisotropy and deformation mechanism in Al−Cu−Zr superplastic alloy," Acta Met., 27--, No. 8, 1313–1318 (1978).

    Google Scholar 

  8. C. D. Ingelbrecht, "R-values of Ti−6Al−4V sheet after superplastic strain," Mater. Sci. and Tech.,3, 36–41 (1978).

    Google Scholar 

Download references

Authors
  1. M. F. Akhmed Fuad
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. M. A. Tsepin
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. A. Lobach
    View author publications

    You can also search for this author in PubMed Google Scholar

Additional information

Tabbinskii Metallurgical Institute, Cairo, Egypt. Moscow Institute of Steel and Alloys. Translated from Metallovenedie i Termicheskaya Obrabotka Metallov, No. 10, pp. 14–16, October, 1991.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Fuad, M.F.A., Tsepin, M.A. & Lobach, A.A. Influence of superplastic deformation on the anisotropy of 03Kh26N6T steel. Met Sci Heat Treat 33, 738–741 (1991). https://doi.org/10.1007/BF00800692

Download citation

  • Issue Date:

  • DOI: https://doi.org/10.1007/BF00800692

Keywords

Search

Navigation