Advertisement

Soviet Powder Metallurgy and Metal Ceramics

, Volume 29, Issue 8, pp 616–621 | Cite as

Effect of the production conditions of rapidly quenched ribbons of alloy Fe-6.5% Si on their structure and magnetic properties

  • V. Z. Balan
  • V. V. Maslov
  • V. K. Nosenko
  • D. Yu. Paderno
Powder-Metallurgy Materials, Products, and Coatings
  • 59 Downloads

Conclusions

Rapid quenching in a protective atmosphere of carbon dioxide at an optimal combination of parameters improves substantially the quality of ribbons of alloy Fe-6.5 Si in comparison with ribbons obtained in air or with the use of helium or argon. Better quality of the ribbons improves substantially the level of their magnetic properties.

The dispersity and homogeneity of the microstructure of the ribbons, determined by the cooling rate, depends, in addition to the thermal conductivity of the material of the quenching disk, on its adhesive property, i.e., on the area of actual contact between the melt and the forming ribbon on the one hand, and the disk on the other, and also on the duration of the contact.

The ductility of rapidly quenched ribbons of alloy Fe-6.5% Si more than 40 μm thick can be improved by their increased cooling rate in contact with the disk, and also by forced cooling after removal from the disk.

The results obtained in the present work can be used in practice in the production of other rapidly quenched microcrystalline or amorphous alloys.

Keywords

Microstructure Atmosphere Dioxide Thermal Conductivity Carbon Dioxide 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Literature cited

  1. 1.
    C. F. Chang, R. L. Bye, V. Laxmanan, and S. K. Das, “Texture and magnetic properties of rapidly quenched Fe-6.5% Si ribbon,” IEEE Trans. Magn.,20, No. 4, 553–558 (1984).Google Scholar
  2. 2.
    V. V. Maslov, V. K. Nosenko, D. E. Ovsienko et al., “Investigation of the processes of structure formation during the solidification of alloy Fe-6.5% Si under conditions of rapid quenching,” Metallofizika,10, No. 2, 15–21 (1988).Google Scholar
  3. 3.
    M. J. Tenwick and H. A. Davies, “The structure and properties of rapidly solidified Fe-3 to 9.3 wt.% Si alloys,” Int. J. Rapid Solidification,85, No. 1, 143–155 (1984).Google Scholar
  4. 4.
    In: Materials of the First International Conference on Rapid Quenching of Metallic Alloys (Varna, May 11–17, 1987), Academy of Sciences of the German Democratic Republic, Obermongwitz (1987), pp. 56–68.Google Scholar
  5. 5.
    D. Pavuna, “Production of metallic glass ribbons by the chillblock melt-spinning technique in stabilized laboratory conditions,” J. Mat. Sci.,16, No. 9, 2419–2433 (1981).Google Scholar
  6. 6.
    Kh. Kh. Liberman, “Effects of the gaseous boundary layer in the production of ribbons of amorphous alloys,” in: Rapidly Quenched Metals, Metallurgiya, Moscow (1983), pp. 37–39.Google Scholar
  7. 7.
    S. C. Huang and H. C. Fiedler, “Effect of wheel surface conditions on the casting of amorphous metal ribbons,” Met. Trans.,12A, No. 6, 1107–1112 (1971).Google Scholar
  8. 8.
    S. N. Zolotarev and A. N. Shumakov, “The relief of the contact surface of rapidly quenched ribbons,” Fiz. Met. Metalloved.,64, No. 2, 349–357 (1987).Google Scholar

Copyright information

© Plenum Publishing Corporation 1991

Authors and Affiliations

  • V. Z. Balan
    • 1
  • V. V. Maslov
    • 1
  • V. K. Nosenko
    • 1
  • D. Yu. Paderno
    • 1
  1. 1.Institute of Metal PhysicsAcademy of Sciences of the Ukrainian SSRUkrain

Personalised recommendations