Questions of the failure mechanics of threaded joints

  • A. A. Chizhik
  • V. I. Gorynin
Science for Production


Failure Mechanic Thread Joint 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.


Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Literature cited

  1. 1.
    A. A. Chizhik, “Calculating the stress intensity factors in spiral rods for determining the supporting capacity of fastener parts of an atomic power station,” Tr. Tsent. Nauch.-Issled, i Proektno-Konstr. Kotloturb. Inst., No. 130, 95–120 (1975).Google Scholar
  2. 2.
    A. A. Chizhik, “The resistance to brittle and ductile failures of materials for the basic elements of power equipment,” Author's Abstract of Doctoral Dissertation, Technical Sciences, Leningrad (1975).Google Scholar
  3. 3.
    I. A. Birger and G. B. Iosilevich, Threaded Connections [in Russian], Mashinostroenie, Moscow (1973).Google Scholar
  4. 4.
    P. Paris and J. Sin, “An analysis of the stressed condition near cracks,” in: Applied Questions of Fracture Toughness [Russian translation], Mir, Moscow (1968), pp. 79–85.Google Scholar
  5. 5.
    H. Neuber and F. Warlo, “Untersuchungen über Probleme der Spannungs Konzentration in der Nähe von Kraftangriffs,” Forsch. Ing.-Wesen,29, No. 6, 176–181 (1963).Google Scholar
  6. 6.
    K. Maruyama, “An analysis of the stresses in threaded joints by the method of finite elements and copper plating (Report 2). The stresses in the tooth spaces under conditions of tensile loading,” Nihon Kikai Gakkai Rombunsyu,39, No. 324, 2340 (1973).Google Scholar
  7. 7.
    S. Masaikhiro, “Determining the stresses in threaded joints on the basis of different methods and assumptions,” Seimitsu Kakai,40, No. 6, 461–467 (1974).Google Scholar
  8. 8.
    H. Otaki, “The distribution of stresses in the tooth spaces of the stud of a “stud-nut” joint (Report 1). The maximum stresses occurring in the tooth spaces of the stud,” Nihon Kikai Gakkai Rombunsyu,37, No. 303, 2197 (1971).Google Scholar
  9. 9.
    M. Nisida, “The stresses in a thread,” Riken Iho,22, No. 5, 385 (1943);23, No. 10–12, 751 (1946).Google Scholar
  10. 10.
    Simamura, “The use of the analysis of stresses by the photoelastic method for machine parts,” Nihon Kakai Gakkai Rombunsyu,66, No. 533, 823 (1963).Google Scholar
  11. 11.
    N. I. Prigorovskii, I. A. Razumovskii, and A. V. Fomin, “An investigation of the force and temperature stresses in the threaded joints of power equipment shells,” in: Experimental Methods of Investigating Deformations and Stresses in Structures [in Russian], Nauka, Moscow (1977), pp. 83–106.Google Scholar
  12. 12.
    ASME Boiler and Pressure Vessel Code. An American National Standard ANSI/ASME BPV-XI. Section XI — Rules for in-Service Inspection of Nuclear Power Components, Division I, Appendix A. Analysis of Flaw Indications (1977), p. 125.Google Scholar
  13. 13.
    N. P. Chironis, “55% thread depth will make beryllium bolts practical,” Prod. Eng.,31, No. 47, 75–77 (1960).Google Scholar
  14. 14.
    V. M. Filatov, “Calculating the elements of a vessel,” in: Strength in Low-Cycle Loading [in Russian], Nauka, Moscow (1975), pp. 120–127.Google Scholar
  15. 15.
    Standards for Calculating the Strength of the Elements of Reactors, Steam Generators, Vessels, and Piping [in Russian], Metallurgiya, Moscow (1973).Google Scholar

Copyright information

© Plenum Publishing Corporation 1982

Authors and Affiliations

  • A. A. Chizhik
    • 1
  • V. I. Gorynin
    • 1
  1. 1.I. I. Polzunov Scientific and Production Union on the Research and Design of Power EquipmentLeningrad

Personalised recommendations