Abstract
Consolidation of rapidly solidified titanium alloy powders employing explosively generated shock pressures was carried out successfully. The cylindrical explosive consolidation technique was utilized, and compacts with densities in the range 97 to 100% were produced. Better consolidation (with more interparticle melting regions and less cracking) was achieved by using a double tube design in which the outer tube (flyer tube) was explosively accelerated, impacting the powder container. Optical and transmission electron microscopy observations were carried out to establish microstructural properties of the products. It was observed that consolidation is achieved by interparticle melting occurring during the process. The interior of the particles in Ti-17 alloy exhibited planar arrays of dislocations and twin-like features characteristic of shock loading. Two dominant types of microstructures (lath and equiaxed) were observed both in Ti-662 and Ti-6242 + 1% Er compacts, and very fine erbia (Er2O3) particles were seen in the latter alloy. The micro-indentation hardness of the consolidated products was found to be higher than that of the as-received powder material; and the yield and ultimate tensile strengths were found to be approximately the same as in the as-cast and forged conditions. The ductilities (as measured by the total elongation) of the shockcompacted materials were much lower than those of the cast or forged alloys. Hot isostatic pressing of the shock-consolidated alloys increased their ductility. This enhancement in ductility is thought to be due to the closure of existing cracks. These excellent mechanical properties are a consequence of strong interparticle bonding between individual powder particles. It was also established that scaling up the powder compacts in size is possible and compacts with 50, 75, and 100 mm diameter were successfully produced.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
R. Prummer and G. Ziegler, Proceedings 6th International Conference on High Energy Rate Fabrication, 1977, Essen, Germany.
V. D. Linse (ed), “Dynamic Compaction of Metal and Ceramic Powder” National Academy of Sciences, National Materials Advisory Board, NMAB Report 394, 1983, p. 54.
M. A. Meyers, B. B. Gupta and L. E. Murr, J. Met. 33 (1981) 21.
R. B. Schwarz, R. Kasiraj, T. Vreeland, Jr. and T. J. Ahrens, Acta Metall. 32 (1984) 1243.
M. A. Meyers and H.-R. Pak, J. Mater. Sci. 20 (1985) 2133.
D. G. Morris, ibid. 17 (1982) 1789.
D. Raybould, Powder Met. 25 (1982) 35.
W. H. Gourdin and J. E. Smugerevsky, Proceedings 3rd Conference on Rapid Solidification Processing, edited by R. Mehrabian (National Bureau of Standards, Washington, DC, 1982) p. 565.
D. Raybould, in“Shock Waves and High-Strain-Rate Phenomena in Metals” edited by M. A. Meyers and L. E. Murr (Plenum Press, New York, 1981) p. 855.
W. H. Gourdin, Prog. Mater. Sci. 30 (1986) 39.
R. Prummer, in“Explosive Welding, Forming, and Compaction” edited by T. Z. Blazynski (Applied Science, London, 1983) p. 369.
M. A. Meyers and S. H. Wang, Acta Metall. 36 (1987) 925.
M. Yoshida and Tirumurti, Center for Explosives Technology Research, 1986, unpublished results.
R. K. Gurney, Ballistic Research Laboratory, BRL Report 405 (1943).
J. E. Reaugh, J. Appl. Phys. 61 (1987) 962.
H.-L. Coker, M.Sc. Dissertation, New Mexico Institute of Mining and Technology, Socorro, New Mexico (1987).
M. A. Meyers and L. E. Murr, (eds) “Shock Waves and High-Strain-Rate Phenomena in Metals” (Plenum Press, New York, 1981).
“Metals Handbook” (American Society of Metals, Metals Park, OH, 1972) p. 342.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Coker, H.L., Meyers, M.A. & Wessels, J.F. Dynamic consolidation of rapidly solidified titanium alloy powders by explosives. J Mater Sci 26, 1277–1286 (1991). https://doi.org/10.1007/BF00544466
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF00544466