Advertisement

Ingenieur-Archiv

, Volume 55, Issue 3, pp 157–175 | Cite as

Limit analysis of circular and annular plates

  • C. Cinquini
  • P. Zanon
Article

Summary

The problem of the plastic collapse load of circular and annular plates is dealt with. For simply supported and built-in edge plates, different loading conditions are considered and the annular plates are studied for varying geometries. The solutions obtained according to both Tresca's and Mises' yield conditions are exact in the sense of limit analysis.

Keywords

Neural Network Complex System Information Theory Nonlinear Dynamics Load Condition 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Zur Grenztragfähigkeits-Theorie bei Kreis- und Kreisringplatten

Übersicht

Es werden Traglasten von Kreis- bzw. Kreisringplatten ermittelt. Dabei werden gelenkig gelagerte sowie eingespannte Kreisplatten bei verschiedener Belastung und Kreisringplatten bei verschiedener Geometrie betrachtet. Die mit Hilfe der Fließbedingungen nach Tresca bzw. v. Mises erhaltenen Lösungen sind exakt im Sinne der Grenztragfähigkeits-Theorie.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Iliouchine, A. A.: Plasticité. Paris: Eyrolles 1956Google Scholar
  2. 2.
    Sawczuk, A.; Jaeger, T.: Grenztragfähigkeits-Theorie der Platten. Berlin, Göttingen, Heidelberg: Springer 1963Google Scholar
  3. 3.
    Prager, W.: An introduction to plasticity. New York: Addison-Wesley 1959Google Scholar
  4. 4.
    Save, M.; Massonnet, Ch.: Calcul plastique des constructions. Centre Belgo-Luxembourgeois d'Information de l'Acier, 1972Google Scholar
  5. 5.
    Sawczuk, A.: Introduction à la flexion plastique des plaques. Proc. of evolution et théories modernes en élasticité et plasticité. St. Rémy-lès-Chevreuse (F), 1977. Ed. du Bâtiment et des Travaux Publics, 1979, pp. 199–274Google Scholar
  6. 6.
    Sokol, I.; Sawczuk, A.: A systematic study of load carrying capacities of rotationally symmetric plates with the Huber-Mises yield condition. Rozpr. Inz. 27 (219–244) 1979Google Scholar
  7. 7.
    Lamblin, D.: Analyse et dimensionnement plastique de coût minimum de plaques circulaires. Thèse de doctorat en Sciences appliquées, Faculté Polytechnique de Mons, 1975Google Scholar
  8. 8.
    Lamblin, D.; Guerlement, G.: Analyse limite de plaques circulaires avec la condition de Von Mises. Bull. Techn. Suisse Romande 1 (1972) 1–8Google Scholar
  9. 9.
    Ballio, G.; Poggi, C.; Zanon, P.: Elastic plastic bending of plates subjected to concentrated loads. Proc. International of Conference on Joints in Structural Steelwork, 6–9 April 1981Google Scholar
  10. 10.
    Poggi, C.; Zanon, P.: Ultimate load evaluation of steel plates subjected to concentrated loads. Costruzioni Metalliche 5 (1983) 295–311Google Scholar
  11. 11.
    Packer, J. A.; Morris, L. J.: A limit state design method for the known region of bolted beam-column connections. The Structural Engineer 5 (1977) 446–458Google Scholar
  12. 12.
    Zoetermeijer, P.: A design method for the tension side of statically loaded bolted beam-to-column connections. Heron 20 (1974) 1–59 Delf UniversityGoogle Scholar

Copyright information

© Springer-Verlag 1985

Authors and Affiliations

  • C. Cinquini
    • 1
  • P. Zanon
    • 1
  1. 1.Department of Structural MechanicsPaviaItaly

Personalised recommendations