Abstract
A single leg bending test is described and its suitability for interfacial fracture toughness testing is evaluated. The test specimen consists of a beam-type geometry comprised of two materials, one ‘top’ and one ‘bottom’, with a split at one end along the bimaterial interface. A portion of the bottom material in the cracked section of the beam is removed and the geometry is loaded in three-point bending. Thus, the reaction force of the support at the cracked end is transmitted only into the material comprising the top portion of the beam. The test is analyzed by a crack tip element analysis and the resulting expressions for energy release rate and mode mixity are verified by comparison with finite element results. It is shown that, by varying the thicknesses of the two materials, the single leg bending test can be used to determine the fracture toughness of most bimaterial interfaces over a reasonably wide range of mode mixities.
Similar content being viewed by others
References
C.F. Shih, Materials Science and Engineering A 143 (1991) 77–90.
J.W. Hutchinson and Z. Suo, Advances in Applied Mechanics 29 (1990) 63–191.
K.M. Liechti and Y.S. Chai, Journal of Applied Mechanics 58 (1991) 680–687.
N.P. O'Dowd, C.F. Shih and M.G. Stout, International Journal of Solids and Structures 25 (1992) 571–589.
D.F. Devitt, R.A. Schapery and W.L. Bradley, Journal of Composite Materials 14 (1980) 270–285.
ASTM Standard D5228-94, Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Reinforced Polymer Matrix Composites, DCB Standard, Philadelphia (1994).
A.J. Russell and K.N. Street, in Progress in Science and Engineering of Composites, 4th International Conference on Composite Materials (ICCM-IV), T. Hayashi, K. Kawata and S. Umekawa (eds.), Japan Society for Composite Materials, Tokyo (1982) 279–286.
L.A. Carlsson, J.W. GillespieJr. and R.B. Pipes, Journal of Composite Materials 20 (1986) 594–604.
J.M. Whitney, in Interlaminar Response of Composite Materials, N.J. Pagano (ed.) Elsevier Science Publishers, New York (1989) 161–250.
J.R. Reeder and J.H. CrewsJr., AIAA Journal 28 (1990) 1270–1276.
J.R. Reeder and J.H. CrewsJr., Journal of Composites Technology and Research 14 (1992) 12–19.
V. Sundararaman and B.D. Davidson, An Unsymmetric Double Cantilever Beam Test for Interfacial Fracture Toughness Determination, International Journal of Solids and Structures, to appear.
A.J. Russell and K.N. Street, in Delamination and Debonding of Materials, ASTM STP 876, W.S. Johnson (ed.), Philadelphia (1985) 349–370.
K.M. Liechti and T. Freda, Journal of Adhesion 28 (1989) 145–169.
S.H. Yoon and C.S. Hong, International Journal of Fracture 43 (1990) R3-R9.
J. Goodelle, R.A. Pearson and T.Y. Wu, in Advanced Materials: Expanding the Horizons, Proceedings of the 25th International SAMPE Technical Conference, R. Trabacco and T. Lynch (eds.) Society for the Advancement of Materials and Process Engineering, W. Covina, California (1993).
M. Charalambides, A.J. Kinloch, Y. Wang and J.G. Williams, International Journal of Fracture 54 (1992) 269–291.
W.E. Bachrach and D.N. Beshers, in Mechanics Computing in 1990's and Beyond, Volume 2: Structural and Material Mechanics, H. Adeli and R.L. Sierakowski (eds.), American Society of Civil Engineers, New York (1991) 933–936.
J.Y. Shim and C.S. Hong, Journal of Reinforced Plastics and Composites 2 (1993) 1295–1310.
V. Sundararaman and B.D. Davidson, in Application of Fracture Mechanics in Electronic Packaging and Materials, EEP Vol. 11/MD Vol. 64, T.Y. Wu, W.T. Chen, R.A. Pearson and D.T. Read (eds.) American Society of Mechanical Engineers, New York (1995), 141–154.
V. Sundararaman, and B.D. Davidson, An Unsymmetric End Notched Flexure Test for Interfacial Fracture Toughness Determination, Technical Report 94–203, Department of Mechanical, Aerospace and Manufacturing Engineering, Syracuse University, Syracuse, NY (1995).
P.G. Charalambides, J. Lund, A.G. Evans and R.M. McMeeking, Journal of Applied Mechanics 56 (1989) 77–82.
B.D. Davidson, C.S. Altonen and J.J. Polaha, in Composite Materials: Testing and Design (Twelfth Volume), ASTM STP 1274, R.B. Deo and C.R. Saff (eds.), Philadelphia (1996) 393–413.
J.M. Whitney, Structural Analysis of Laminated Anisotropic Plates, Technomic Publishing Company, Lancaster, PA (1987).
D. Broek, Elementary Engineering Fracture Mechanics, 4th Edition, Kluwer Academic Publishers, Dordrecht, Netherlands (1986).
J.J. Polaha, B.D. Davidson, R.C. Hudson and A. Pieracci, Journal of Reinforced Plastics and Composites 15 (1996) 141–173.
B.D. Davidson, H. Hu and R.A. Schapery Journal of Applied Mechanics 62 (1995) 294–305.
R.A. Schapery and B.D. Davidson, Applied Mechanics Reviews 43 (1990) S281-S287.
Z. Suo and J.W. Hutchinson, International Journal of Fracture 43 (1990) 1–18.
B.D. Davidson, R. Krüger and M. König, Composites Science and Technology 54 (1995) 385–394.
J. Dundurs, Journal of Applied Mechanics 36 (1969) 650–652.
J.R. Rice, Journal of Applied Mechanics 55 (1988) 98–103.
M.G. Stout, N.P. O'Dowd and C.F. Shih, in Experiments in Micromechanisms of Failure Resistant Materials, Proceedings of the ASME Winter Annual Meeting, AMD Vol. 130, K.S. Kim (ed.), American Society of Mechanical Engineers, New York (1991) 9–16.
E.F. Rybicki and M.F. Kanninen, Engineering Fracture Mechanics 9 (1977) 931–938.
P.P.L. Matos, R.M. McMeeking, P.G. Charalambides and M.D. Drory, International Journal of Fracture 40 (1989) 235–254.
T. Nakamura, Journal of Applied Mechanics 58 (1991) 939–946.
T. Nakamura, in Fracture Mechanics: Twenty-Second Symposium (Volume 1), ASTM STP 1131, H.A. Ernst, A. Saxena and D.L. McDowell (eds.), Philadelphia (1992) 635–649.
R.S. Barsoum and T.K. Chen, International Journal of Fracture 50 (1991) 221–237.
F. Ghahremani and C.F. Shih, Journal of Applied Mechanics 59 (1992) 61–68.
Y.J. Lee and A.J. Rosakis, International Journal of Solids and Structures 30 (1993) 3139–3158.
T. Nakamura and D.M. Parks, Journal of Applied Mechanics 55 (1988) 805–813.
T. Nakamura and D.M. Parks, International Journal of Solids and Structures 25 (1989) 1411–1426.
K.M. Liechti, Y.S. Chai and Y.M. Liang, Experimental Mechanics 32 (1992) 218–224.
B.D. Davidson and R.A. Schapery, Journal of Composite Materials 22 (1988) 640–656.
B.D. Davidson, Journal of Composite Materials 24 (1990) 1124–1137.
B.D. Davidson, R. Krüger and M. König, Journal of Composite Materials 29 (1995) 2108–2133.
G. Gospodnetic, Journal of Applied Mechanics 26 (1959) 675–676.
A. Ohtsuki, Bulletin of the JSME 29 (1986) 1988–1995.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Davidson, B.D., Sundararaman, V. A single leg bending test for interfacial fracture toughness determination. Int J Fract 78, 193–210 (1996). https://doi.org/10.1007/BF00034525
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/BF00034525