Advertisement

Wear behavior of TC11 and AISI M2 in pin–disk tribo-system

  • Lan Wang
  • Jing-han Yang
  • Yang Li
  • Jie Song
  • Yun-xue Jin
  • Shu-qi WangEmail author
Original Paper
  • 15 Downloads

Abstract

The wear behavior and mechanism of TC11 (pins) and AISI M2 (disks) under different test conditions were studied. The results show that tribo-layers formed on the worn surfaces of both TC11 alloy and AISI M2 steel. As for TC11 alloys at 25 °C, the wear rate increased to high values with an increase in the load; and abrasive wear and adhesive wear prevailed. However, at 600 °C, the wear rate decreased sharply and oxidative wear prevailed. As for AISI M2 steels, at 25 and 600 °C, the wear rates were relatively low. The wear mechanisms at 25 and 600 °C were abrasive wear and oxidative wear, respectively. The wear rates of AISI M2 steel were lower than those of TC11 alloy at 25 and 600 °C. The wear performance of the tribo-pair was noticed to be closely related to their mutual contact mode except for the test conditions and the pin and disk materials, and the intermittent contact mode reduced wear of AISI M2 steel.

Keywords

Wear mechanism Tribo-system Tribo-layer Wear rate Contact mode 

Notes

Acknowledgements

This work is financially supported by Jiangsu Provincial Key Laboratory for Interventional Medical Devices (No. jr1506) and the initial fund of Jiangsu University Senior Talent (No. 15JDG076) is gratefully acknowledged.

References

  1. [1]
    D.A. Rigney, Wear 152 (1992) 187–192.CrossRefGoogle Scholar
  2. [2]
    W.M. Ke, F.C. Zhang, Z.N. Yang, M. Zhang, Mater. Charact. 82 (2013) 120–129.CrossRefGoogle Scholar
  3. [3]
    E. Marui, N. Hasegawa, H. Endo, K. Tanaka, T. Hattori, Wear 205 (1997) 186–199.CrossRefGoogle Scholar
  4. [4]
    M.J. Ghazali, W.M. Rainforth, H. Jones, Tribol. Int. 40 (2007) 160–169.CrossRefGoogle Scholar
  5. [5]
    Z.R. Yang, M.X. Wei, Y.T. Zhao, S.Q. Wang, Trans. Nonferrous Met. Soc. China 11 (2011) 2584-2591.CrossRefGoogle Scholar
  6. [6]
    E.M. Abdel-Wahab, Mater. Sci. Eng. A 473 (2008) 330–335.CrossRefGoogle Scholar
  7. [7]
    H.W. Song, S.H. Zhang, M. Cheng. J. Alloy. Compd. 480 (2009) 922–927.CrossRefGoogle Scholar
  8. [8]
    M.V. Berdin, L.A. Karavaeav, L.A. Syutina, S.K. Nurieva, Met. Sci. Heat Treat. 46 (2004) 54–60.CrossRefGoogle Scholar
  9. [9]
    Y. Gu, F.H. Gu, Y.L. Qi, C.Q. Xia, X. Xiong, Mater. Sci. Eng. A 575 (2013) 74–85.CrossRefGoogle Scholar
  10. [10]
    D.H. Lu, M.Y. Gu, Z.L. Shi, Tribol. Lett. 6 (1999) 57–61.CrossRefGoogle Scholar
  11. [11]
    D.A. Rigney, Wear 245 (2000) 1–9.CrossRefGoogle Scholar
  12. [12]
    J.L. Young Jr, D. Kuhlmann-Winsdorf, R. Hull, Wear 246 (2000) 74–90.CrossRefGoogle Scholar
  13. [13]
    G. Straffelini, A. Molinari, Wear 236 (1999) 328–338.CrossRefGoogle Scholar
  14. [14]
    A. Molinari, G. Straffelini, B. Tesi, T. Bacci, Wear 208 (1997) 105–112.CrossRefGoogle Scholar
  15. [15]
    M. Qiu, Y.Z. Zhang, J.H. Yang, J. Zhu, Mater. Sci. Eng. A 434 (2006) 71–75.CrossRefGoogle Scholar
  16. [16]
    M. Qiu, Y.Z. Zhang, J.H. Yang, J. Zhu, Tribology 23 (2006) 203–207.Google Scholar
  17. [17]
    Y.S. Mao, L. Wang, K.M. Chen, S.Q. Wang, X.H. Cui, Wear 297 (2013) 1032–1039.CrossRefGoogle Scholar
  18. [18]
    X.H. Cui, Y.S. Mao, M.X. Wei, S.Q. Wang, Tribol. Trans. 55 (2012) 185–190.CrossRefGoogle Scholar
  19. [19]
    L. Wang, S.Q. Wang, H.Y. Ding, A.H. Liu, Tribology 36 (2016) 592–598.Google Scholar
  20. [20]
    L. Wang, H.Y. Ding, A.H. Liu, S.Q. Wang, Rare Met. Mater. Eng. 46 (2017) 2449–2454.Google Scholar
  21. [21]
    M.O. Alam, A.S.M.A. Haseeb, Tribol. Int. 35 (2002) 357–362.CrossRefGoogle Scholar
  22. [22]
    R.S. Magaziner, V.K. Jain, S. Mall, Wear 267 (2009) 368–373.CrossRefGoogle Scholar
  23. [23]
    M.C. Gui, S.B. Kang, J.M. Lee, Wear 240 (2000) 186–198.CrossRefGoogle Scholar
  24. [24]
    A. Pauschitza, M. Roy, F. Franek, Tribol. Int. 41 (2008) 584–602.CrossRefGoogle Scholar
  25. [25]
    P.J. Blau, Tribol. Int. 43 (2010) 1203–1208.CrossRefGoogle Scholar
  26. [26]
    M.X. Wei, S.Q. Wang, L. Wang, X.H. Cui, K.M. Chen, J. Iron Steel Res. Int. 19 (2012) No. 5, 50–57.CrossRefGoogle Scholar
  27. [27]
    M.J. Ghazali, W.M. Rainforth, M.Z. Omar, J. Mater. Process. Technol. 201 (2008) 662–668.CrossRefGoogle Scholar
  28. [28]
    S.Q. Wang, M.X. Wei, Y.T. Zhao, Wear 269 (2010) 424–434.CrossRefGoogle Scholar
  29. [29]
    Q.Y. Zhang, S.Q. Wang, L. Wang, Appl. Mech. Mater. 331 (2013) 559–562.CrossRefGoogle Scholar
  30. [30]
    M.X. Wei, S.Q. Wang, K.M. Chen, X.H. Cui, Wear 272 (2011) 110–121.Google Scholar

Copyright information

© China Iron and Steel Research Institute Group 2019

Authors and Affiliations

  • Lan Wang
    • 1
  • Jing-han Yang
    • 2
  • Yang Li
    • 2
  • Jie Song
    • 2
  • Yun-xue Jin
    • 3
  • Shu-qi Wang
    • 1
    Email author
  1. 1.School of Materials Science and EngineeringJiangsu UniversityZhenjiangChina
  2. 2.Jingjiang CollegeJiangsu UniversityZhenjiangChina
  3. 3.School of Materials Science and EngineeringJiangsu University of Science and TechnologyZhenjiangChina

Personalised recommendations