Experimental Techniques

, Volume 42, Issue 2, pp 233–241 | Cite as

Study of Ball Burnishing Process on the Surface Roughness and Microhardness of AZ91D Alloy

Article
  • 190 Downloads

Abstract

Ball burnishing is a simple, rapid, cost-effective and superfinishing process which is generally carried out to better the surface integrity of mechanical parts. The aim of this paper is to investigate the optimum surface roughness and microhardness of AZ91D magnesium alloy by utilizing ball burnishing process. The effects of the number of passes, burnishing force, burnishing speed and feed rate were researched on surface roughness and microhardness of AZ91D magnesium alloy. Taguchi L18 orthogonal array was applied to plan the experiments of ball burnishing process. The optimum burnishing parameter was determined based on signal-to-noise ratio. The best surface roughness of 0.336 μm was achieved by the number of passes: 2, burnishing force 250 N, burnishing speed: 200 rpm, feed rate: 0.1 mm/min. The best microhardness of 102.7 HV was achieved by the number of passes 2, burnishing force 250 N, burnishing speed: 600 rpm and feed rate: 0.25 mm/min.

Keywords

Magnesium Surface roughness Taguchi method Ball burnishing 

References

  1. 1.
    Buldum BB, Sik A, Ozkul I (2013) Investigation of magnesium alloys machinability. Int J Electron Mech Mechatronc Eng 2:261–268Google Scholar
  2. 2.
    Ugurlu M, Cagan SC, Buldum BB (2017) Improvement of surface roughness using ANOVA for AZ31B magnesium alloy with ball burnishing process. Int J Engine Res Technol 6(9):216–221Google Scholar
  3. 3.
    Fernandus MJ, Senthilkumar T, Balasubramanian V, Rajakumar S (2014) Optimizing diffusion bonding parameters to maximize the strength of AA6061 aluminum and AZ61A magnesium alloy joints. Exp Tech 32(21):23–36Google Scholar
  4. 4.
    Akyuz B (2013) Influence of al content on machinability of AZ series mg alloys. Trans Nonferrous Metals Soc China 23:2243–2249CrossRefGoogle Scholar
  5. 5.
    Korzynski M, Zarski T (2016) Slide diamond burnishing influence on of surface stereometric structure of an AZ91 alloy. Surf Coat Technol 307:590–595CrossRefGoogle Scholar
  6. 6.
    Fouad Y, Mhaede M, Wagner L (2010) Effects of mechanical surface treatments on fatigue performance of extruded ZK60 alloy. Fatigue Fract Eng Mater Struct 34:403–407CrossRefGoogle Scholar
  7. 7.
    Asilturk I (2012) Application of artificial intelligent to predict surface roughness. Exp Tech 38(4):54–60CrossRefGoogle Scholar
  8. 8.
    Chakraborty S, Kar S, Dey V, Ghosh SK (2017) Optimization and surface modification of al-6351 alloy using SiC–cu green compact electrode by electro discharge coating process. Surf Rev Lett 24:1750007-1-12CrossRefGoogle Scholar
  9. 9.
    Aldas K, Ozkul I, Eskil M (2014) Prediction of surface roughness in longitudinal turning process by a genetic learning algorithm. Mater Test 56:375–380CrossRefGoogle Scholar
  10. 10.
    Taskesen A, Aldas K, Ozkul I, Kutukde K, Zumrut Y (2014) Analysis of thrust force in drilling B4C-reinforced aluminium alloy using genetic learning algorithm. Int J Adv Manuf Technol 75:237–245CrossRefGoogle Scholar
  11. 11.
    Vikram Reddy V, Madar Valli P, Kumar A, Sridhar Reddy CH (2015) Influence of process parameters on characteristics of electrical discharge machining of ph17-4 stainless steel. J Adv Manuf Syst 14:189–202CrossRefGoogle Scholar
  12. 12.
    Hamamci M, Topal ES (2015) Consideration of step-over ratio in optimization of cutting parameters for surface roughness during high speed machining. J Balkan Tribol Assoc 21:753–766Google Scholar
  13. 13.
    Basak H, Ozkan S, Taskesen A (2011) Application of burnishing process on friction stir welding and investigation of the effect of burnishing process on the surface roughness, hardness and strength. Exp Tech 35(1):8–16CrossRefGoogle Scholar
  14. 14.
    Bounouara A, Hamadache H, Amirat A (2017) Investigation on the effect of ball burnishing on fracture toughness in spiral API X70 pipeline steel. Int J Adv Manuf Technol 1–9Google Scholar
  15. 15.
    Rodriguez A, de Lacelle Lopez LN, Celaya A, Lamikiz A, Albizuri J (2010) Surface improvement of shafts by the deep ball-burnishing technique. Surf Coat Technol 206:2817–2824CrossRefGoogle Scholar
  16. 16.
    Shiou FJ, Huang SJ, Shih AJ, Zhu J, Yoshimo M (2017) Fine surface finish of a hardened stainless steel using a new burnishing tool. Procedia Manuf 10:208–217CrossRefGoogle Scholar
  17. 17.
    Revankar GD, Shetty R, Rao SS, Gaitonde VN (2017) Wear resistance enhancement of titanium alloy (Ti-6Al-4V) by ball burnishing process. J Mater Res Technol 6:13–32CrossRefGoogle Scholar
  18. 18.
    Banh QN, Shiou FJ (2016) Determination of optimal small ball-burnishing parameters for both surface roughness and superficial hardness improvement of STAVAX. Arab J Sci Eng 41:639–652CrossRefGoogle Scholar
  19. 19.
    Low KO, Wong KJ (2011) Influence of ball burnishing on surface quality and tribological characteristics of polymers under dry sliding conditions. Tribol Int 44:44–153CrossRefGoogle Scholar
  20. 20.
    Grzesik W, Zak K (2014) Characterization of surface integrity produced by sequential dry hard turning and ball burnishing operations. J Manuf Sci Eng 136:031017-1-031017-9CrossRefGoogle Scholar
  21. 21.
    El-Axir MH, Othman OM, Abodiena AM (2008) Improvements in out-of-roundness and microhardness of inner surfaces by internal ball burnishing process. J Mater Process Technol 196:120–128CrossRefGoogle Scholar
  22. 22.
    Gokce B (2015) Analysis of wear behaviours of borided 440C steels by using taguchi method. J Balkan Tribol Assoc 21:831–841Google Scholar
  23. 23.
    Kayali Y, Gokce B, Mertgenc E, Colak F, Kara R (2013) Analysis of wear behaviour of borided AISI 52100 steel with the taguchi method. J Balkan Tribol Assoc 19:365–376Google Scholar
  24. 24.
    Grzesik W, Zak K (2012) Modification of surface finish produced by hard turning using superfinishing and burnishing operations. J Mater Process Technol 212:315–322CrossRefGoogle Scholar
  25. 25.
    Thamizhmnaii S, BB OMAR, Saparudin S, Hasan S (2008) Surface roughness investigation and hardness by burnishing on titanium alloy. J Achiev Mater Manuf Eng 28:139–142Google Scholar
  26. 26.
    Yuan X, Sun Y, Li C, Liu W (2017) Experimental investigation into the effect of low plasticity burnishing parameters on the surface integrity of TA2. Int J Adv Manuf Technol 88:1089–1099CrossRefGoogle Scholar
  27. 27.
    Cicek A, Kivak T, Ekici E (2015) Optimization of drilling parameters using taguchi technique and response surface methodology (RSM) in drilling of AISI 304 steel with cryogenically treated HSS drills. J Intell Manuf 26:295–305CrossRefGoogle Scholar
  28. 28.
    Oktem H, Erzurumlu T, Col M (2006) A study of the taguchi optimization method for surface roughness in finishing milling of mold surfaces. Int J Adv Manuf Technol 28:694–700CrossRefGoogle Scholar
  29. 29.
    Pishbin F, Simchi A, Ryan P, Boccaccini AR (2010) A study of the electrophoretic deposition of bioglass suspensions using the taguchi experimental design approach. J Eur Ceram Soc 30:2963–2970CrossRefGoogle Scholar
  30. 30.
    Gaitonde VN, Karnik SR, Achyutha BT, Siddeswarappa B (2006) Multi-response optimization in drilling using taguchi’s quality loss function. Indian J Eng Mater Sci 13:484–488Google Scholar
  31. 31.
    Carou D, Rubio EM, Lauro CH, Davim JP (2014) Experimental investigation on surface finish during intermittent turning of UNS M11917 magnesium alloy under dry and near dry machining conditions. Measurement 56:136–154CrossRefGoogle Scholar
  32. 32.
    Phadke MS (1989) Quality engineering using robust design. Prentice Hill, New YorkGoogle Scholar
  33. 33.
    Nemat M, Lyons A (2000) An investigation of the surface topography of ball burnished mild steel and aluminium. Int J Adv Manuf Technol 16:469–473CrossRefGoogle Scholar
  34. 34.
    Rao SD, Hebbar SH, Komaraiah M, Kempaiah UN (2008) Investigations on the effects of ball burnishing parameters on surface roughness and corrosion resistance of HSLA dual-phase steels. East Afr J Sci 2:164–169Google Scholar
  35. 35.
    Rao SD, Hebbar SH, Komaraiah M, Kempaiah UN (2008) Investigations on the effects of ball burnishing parameters on surface hardness and wear resistance of HSLA dual-phase steels. Mater Manuf Process 23:295–302CrossRefGoogle Scholar
  36. 36.
    Al Quran FMF (2015) The effect of roller burnishing on surface hardness and roughness of aluminum alloy. Int J Mech Appl 5(2):37–40Google Scholar
  37. 37.
    Hamid H, Wahiba T, Zahia Z (2014) Characterization layers hardened burnished steel AISI/SAE 3115. Int J Mech Appl 4(1):13–19Google Scholar

Copyright information

© The Society for Experimental Mechanics, Inc 2017

Authors and Affiliations

  1. 1.Department of Mechanical Engineering, Engineering FacultyMersin UniversityMersinTurkey

Personalised recommendations