Advertisement

Recent Advances in the Machining of Titanium Alloys using Minimum Quantity Lubrication (MQL) Based Techniques

  • Salman PervaizEmail author
  • Saqib Anwar
  • Imran Qureshi
  • Naveed Ahmed
Review Paper

Abstract

Titanium alloys are generally known as difficult-to-machine materials because of their low machinability ratings. Their usage is favored for demanding sectors because of their high strength to weight ratio, high corrosion resistance and ability to operate at elevated temperatures. Machining of titanium alloys results in higher environmental burden, because they require high energy and generous amount of cutting fluids during machining. It is a well-known fact that most of the cutting fluids are toxic and non-biodegradable in nature and their disposal is costly. Therefore, researchers in metal cutting are keen to explore the potential of minimum quantity lubrication (MQL) and minimum quantity cooling lubrication (MQCL) based cooling techniques as an alternate to conventional flood cooling. When MQL and MQCL techniques are used by employing biodegradable vegetable based oils then there is an encouraging potential of replacing the non-biodegradable cutting fluids. This study documents the recent experimental and numerical advances achieved in the MQL and MQCL assisted techniques for machining titanium alloys. The study also highlights the current challenges in this area and recommends future work to address these challenges.

Keywords

Minimum quantity lubrication MQL Minimum quantity cooling lubrication MQCL Titanium alloys 

Notes

Acknowledgement

The research was supported by Rochester Institute of Technology - Dubai (RIT-D), United Arab Emirates. No conflict of interest exists for all participating authors..

References

  1. 1.
    Boyer, R. R. (1996). An overview on the use of titanium in the aerospace industry. Materials Science and Engineering A, 213(1–2), 103–114.CrossRefGoogle Scholar
  2. 2.
    Leyens, C. & Peters, M. (2003). Titanium an titanium alloys.Google Scholar
  3. 3.
    Boyer, R. R., & Briggs, R. D. (2005). The use of beta titanium alloys in the aerospace industry. Journal of Materials Engineering and Performance, 14(6), 680–684.CrossRefGoogle Scholar
  4. 4.
    Inagaki, I. (2014). Application and features of titanium for the aerospace industry, 106.Google Scholar
  5. 5.
    Soo, S. L., Hood, R., Aspinwall, D. K., Voice, W. E., & Sage, C. (2011). Machinability and surface integrity of RR1000 nickel based superalloy. CIRP Annals-Manufacturing Technology, 60(1), 89–92.CrossRefGoogle Scholar
  6. 6.
    Pervaiz, S., Rashid, A., Deiab, I., & Nicolescu, M. (2014). Influence of tool materials on machinability of titanium- and nickel-based alloys: a review. Materials and Manufacturing Processes, 29(3), 219–252.CrossRefGoogle Scholar
  7. 7.
    Gurrappa, I. (2003). Characterization of titanium alloy Ti-6Al-4 V for chemical, marine and industrial applications. Materials Characterization, 51(2–3), 131–139.CrossRefGoogle Scholar
  8. 8.
    Gorynin, I. (1999). Titanium alloys for marine application. Materials Science and Engineering A, 263(2), 112–116.CrossRefGoogle Scholar
  9. 9.
    Schutz, R., & Watkins, H. (1998). Recent developments in titanium alloy application in the energy industry. Materials Science and Engineering A, 243(1–2), 305–315.CrossRefGoogle Scholar
  10. 10.
    Rack, H. J., & Qazi, J. I. (2006). Titanium alloys for biomedical applications. Materials Science and Engineering C, 26(8), 1269–1277.CrossRefGoogle Scholar
  11. 11.
    Elias, C. N., Lima, J. H. C., Valiev, R., & Meyers, M. A. (2008). Biomedical applications of titanium and its alloys. JOM, 60, 46–49.CrossRefGoogle Scholar
  12. 12.
    Ezugwu, E. O., & Wang, Z. M. (1997). Materials Titanium alloys and their machinability. Journal of Materials Processing Technology, 68, 262–274.CrossRefGoogle Scholar
  13. 13.
    Ezugwu, E., Bonney, J., & Yamane, Y. (2003). An overview of the machinability of aeroengine alloys. Journal of Materials Processing Technology, 134(2), 233–253.CrossRefGoogle Scholar
  14. 14.
    Ezugwu, E. O. (2004). High speed machining of aero-engine alloys. Journal of the Brazilian society of Mechanical Sciences and Engineering, 26(1), 1–11.CrossRefGoogle Scholar
  15. 15.
    Paulo Davim, J. (2014). Machining of titanium alloys. Berlin: Springer.Google Scholar
  16. 16.
    Pramanik, A. (2014). Problems and solutions in machining of titanium alloys. International Journal of Advanced Manufacturing Technology, 70(5–8), 919–928.CrossRefGoogle Scholar
  17. 17.
    Boothroyd, G., & Knight, W. A. (1989). Fundamentals of machining and machine tools (2nd ed.). Newyork: Marcel Dekker.Google Scholar
  18. 18.
    Quintana, G., & Ciurana, J. (2011). Chatter in machining processes: A review. International Journal of Machine Tools and Manufacture, 51(5), 363–376.CrossRefGoogle Scholar
  19. 19.
    Rhim, S., & Oh, S. (2006). Prediction of serrated chip formation in metal cutting process with new flow stress model for AISI 1045 steel. Journal of Materials Processing Technology, 171(3), 417–422.CrossRefGoogle Scholar
  20. 20.
    Konig, W. (1978). Applied research on the machinability of titanium and its alloys. In: Proceedings of AGARD conference advanced fabrication processes, Florence.Google Scholar
  21. 21.
    Ekinović, S., Begović, E., & Lušija, A. (2015). Investigation of Influence of MQL machining parameters on cutting forces during MQL turning of carbon steel St52-3. Procedia Engineering, 132, 608–614.CrossRefGoogle Scholar
  22. 22.
    Yoshimura, H., Itoigawa, F., & Nakamura, T. (2005). Development of nozzle system for oil-on-water droplet metalworking fluid and its application to practical production line *. JSME, 48(4), 723–729.Google Scholar
  23. 23.
    Pereira, O., et al. (2015). The use of hybrid CO2+ MQL in machining operations. Procedia Engineering, 132, 492–499.CrossRefGoogle Scholar
  24. 24.
    Nath, C., Kapoor, S. G., Devor, R. E., Srivastava, A. K., & Iverson, J. (2012). Design and evaluation of an atomization-based cutting fluid spray system in turning of titanium alloy. Journal of Manufacturing Processes, 14(4), 452–459.CrossRefGoogle Scholar
  25. 25.
    Su, Y., Gong, L., Li, B., Liu, Z., & Chen, D. (2016). Performance evaluation of nanofluid MQL with vegetable-based oil and ester oil as base fluids in turning. International Journal of Advanced Manufacturing Technology, 83(9–12), 2083–2089.CrossRefGoogle Scholar
  26. 26.
    Chetan, B. C., Behera, S., Ghosh, S., & Rao, P. V. (2016). Wear behavior of PVD TiN coated carbide inserts during machining of Nimonic 90 and Ti6Al4 V superalloys under dry and MQL conditions. Ceramics International, 42(13), 14873–14885.CrossRefGoogle Scholar
  27. 27.
    Maruda, R. W., et al. (2016). A study on droplets sizes, their distribution and heat exchange for minimum quantity cooling lubrication (MQCL). International Journal of Machine Tools and Manufacture, 100, 81–92.CrossRefGoogle Scholar
  28. 28.
    Pejryd, L., Beno, T., & Isaksson, M. (2010). Machining aerospace materials with room-temperature and cooled minimal-quantity cutting fluids. Part B: Journal of Engineering Manufacture, 225, 74–86.Google Scholar
  29. 29.
    Pervaiz, S., Deiab, I., Rashid, A., & Nicolescu, M. (2015). Minimal quantity cooling lubrication in turning of Ti6Al4 V: Influence on surface roughness, cutting force and tool wear. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 231, 1542–1558.CrossRefGoogle Scholar
  30. 30.
    Pervaiz, S., Rashid, A., Deiab, I., & Nicolescu, C. M. (2016). An experimental investigation on effect of minimum quantity cooling lubrication (MQCL) in machining titanium alloy (Ti6Al4 V). International Journal of Advanced Manufacturing Technology, 87, 1371–1386.CrossRefGoogle Scholar
  31. 31.
    Pervaiz, S., Deiab, I., & Darras, B. (2013). Power consumption and tool wear assessment when machining titanium alloys. International Journal of Precision Engineering and Manufacturing, 14(6), 925–936.CrossRefGoogle Scholar
  32. 32.
    Deiab, I., Raza, S. W., & Pervaiz, S. (2014). Analysis of lubrication strategies for sustainable machining during turning of titanium ti-6al-4v alloy. Procedia CIRP, 17, 766–771.CrossRefGoogle Scholar
  33. 33.
    Garcia, U., & Ribeiro, M. V. (2015). Ti6Al4 V titanium alloy end milling with minimum quantity of fluid technique use. Materials and Manufacturing Processes, 31, 1–14.Google Scholar
  34. 34.
    Lv, D., Xu, J., Ding, W., Fu, Y., Yang, C., & Su, H. (2016). Tool wear in milling Ti40 burn-resistant titanium alloy using pneumatic mist jet impinging cooling. Journal of Materials Processing Technology, 229, 641–650.CrossRefGoogle Scholar
  35. 35.
    Ganguli, S., & Kapoor, S. G. (2016). Improving the performance of milling of titanium alloys using the atomization-based cutting fluid application system. Journal of Manufacturing Processes, 23, 29–36.CrossRefGoogle Scholar
  36. 36.
    Park, K. H., Yang, G. D., Lee, M. G., Jeong, H., Lee, S. W., & Lee, D. Y. (2014). Eco-friendly face milling of titanium alloy. International Journal of Precision Engineering and Manufacturing, 15(6), 1159–1164.CrossRefGoogle Scholar
  37. 37.
    Priarone, P. C., Robiglio, M., Settineri, L., & Tebaldo, V. (2014). Milling and turning of titanium aluminides by using minimum quantity lubrication. Procedia CIRP, 24, 62–67.CrossRefGoogle Scholar
  38. 38.
    Qin, X., et al. (2012). Feasibility study on the minimum quantity lubrication in high-speed helical milling of Ti-6Al-4 V. Journal of Advanced Mechanical Design, Systems, and Manufacturing, 6(7), 1222–1233.CrossRefGoogle Scholar
  39. 39.
    Masato, O., Naoki, A., Eisuke, S., Rachid, M., & Takashi, U. (2014). Cutting performance of an indexable insert drill for difficult-to-cut materials under supplied oil mist. International Journal of Advanced Manufacturing Technology, 72(1–4), 475–485.Google Scholar
  40. 40.
    Rahim, E. A., & Sasahara, H. (2011). A study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys. Tribology International, 44(3), 309–317.CrossRefGoogle Scholar
  41. 41.
    Pervaiz, S., Deiab, I., Ibrahim, E. M., Rashid, A., & Nicolescua, M. (2014). A coupled FE and CFD approach to predict the cutting tool temperature profile in machining. Procedia CIRP, 17, 750–754.CrossRefGoogle Scholar
  42. 42.
    Pervaiz, S., Deiab, I., Wahba, E., Rashid, A., & Nicolescu, C. M. (2015). A novel numerical modeling approach to determine the temperature distribution in the cutting tool using conjugate heat transfer (CHT) analysis. International Journal of Advanced Manufacturing Technology, 80(5), 1039–1047.CrossRefGoogle Scholar
  43. 43.
    Duchosal, A., Werda, S., Serra, R., Leroy, R., & Hamdi, H. (2015). Numerical modeling and experimental measurement of MQL impingement over an insert in a milling tool with inner channels. International Journal of Machine Tools and Manufacture, 94, 37–47.CrossRefGoogle Scholar
  44. 44.
    Duchosal, A., Serra, R., Leroy, R., & Hamdi, H. (2015). Numerical optimization of the minimum quantity lubrication parameters by inner canalizations and cutting conditions for milling finishing process with Taguchi method. Journal of Cleaner Production, 108, 65–71.CrossRefGoogle Scholar
  45. 45.
    Duchosal, A., Serra, R., Leroy, R., Bonhoure, D., & Hamdi, H. (2015). Tool design effect on microlubrication spray efficiency in milling using inner channels. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 231, 1–11.Google Scholar
  46. 46.
    Fallenstein, F., & Aurich, J. C. (2014). CFD based investigation on internal cooling of twist drills. Procedia CIRP, 14, 293–298.CrossRefGoogle Scholar
  47. 47.
    Pervaiz, S., Deiab, I., Wahba, E., Rashid, A., & Nicolescu, M. (2017). A numerical and experimental study to investigate convective heat transfer and associated cutting temperature distribution in single point turning. The International Journal of Advanced Manufacturing Technology.  https://doi.org/10.1007/s00170-017-0975-9.Google Scholar

Copyright information

© Korean Society for Precision Engineering 2019

Authors and Affiliations

  • Salman Pervaiz
    • 1
    Email author
  • Saqib Anwar
    • 2
  • Imran Qureshi
    • 3
  • Naveed Ahmed
    • 4
    • 5
  1. 1.Department of Mechanical EngineeringRochester Institute of Technology-DubaiDubaiUnited Arab Emirates
  2. 2.Industrial Engineering Department, College of EngineeringKing Saud UniversityRiyadhSaudi Arabia
  3. 3.Department of Mechanical EngineeringAmerican University of SharjahSharjahUnited Arab Emirates
  4. 4.Department of Industrial and Manufacturing EngineeringUniversity of Engineering and TechnologyLahorePakistan
  5. 5.Raytheon Chair for Systems Engineering (RCSE Chair), Advanced Manufacturing InstituteKing Saud UniversityRiyadhSaudi Arabia

Personalised recommendations