Advertisement

Friction

pp 1–18 | Cite as

Wear properties of copper and copper composites powders consolidated by high-pressure torsion

  • Mohamed Ibrahim Abd El AalEmail author
Open Access
Research Article
  • 15 Downloads

Abstract

The wear characteristics of Cu and Cu-SiC composite microsize powders consolidated by cold compaction combined with sintering or high-pressure torsion (HPT) were investigated. The HPT processed (HPTed) samples with bimodal and trimodal microstructures and fine Cu grains and SiC particle sizes have superior hardness, reasonable ductility level, and high wear resistance. The wear mass loss and coefficient of friction of HPTed samples were remarkably lower than that of cold-compacted and sintered samples as well as that of micro and nano Cu and Cu-SiC composites from previous studies. The sample fabrication method has an apparent influence on the wear mechanism. The wear mechanism was converted from adhesive, delamination, three-body mechanism, grooves (take off the SiC particles), and cracks into abrasive wear after HPT. Oxidization can be considered a dominant wear mechanism in all cases. The worn surface morphology and analysis support the relationship between wear mechanism and characteristics.

Keywords

Cu-SiC composite powders high-pressure torsion (HPT) fine and coarse grains wear characteristics worn surface morphology 

References

  1. [1]
    Pascoe K J. An Introduction to the Properties of Engineering Materials. UK: Van Nostrand Reinhold (UK) Co. Ltd, 1982.Google Scholar
  2. [2]
    Mallick P K. Composites Engineering Handbook. Marcel Dekker Inc, 1997.CrossRefGoogle Scholar
  3. [3]
    Ralph B, Yuen H C, Lee W B. The processing of metal matrix composites—An overview. J Mater Process Technol 63: 339–353 (1997)CrossRefGoogle Scholar
  4. [4]
    Tjong S C, Lau K C. Tribological behaviour of SiC particle-einforced copper matrix composites. Mater Lett 43: 274–280 (2000)CrossRefGoogle Scholar
  5. [5]
    Moustafa S F, Abdel-Hamid Z, Abd-Elhay A M. Copper matrix SiC and Al2O3 particulate composites by powder metallurgy technique. Mater Lett 53: 244–249 (2002)CrossRefGoogle Scholar
  6. [6]
    Dhokey N B, Paretkar R K. Study of wear mechanisms in copper-based SiCp (20% by volume) reinforced composite. Wear 265: 117–133 (2008)CrossRefGoogle Scholar
  7. [7]
    Ramesh C S, Ahmed R N, Mujeebu M A, Abdullah M Z. Development and performance analysis of novel cast copper-SiC-Gr hybrid composites. Mater Des 30: 1957–1965 (2009)CrossRefGoogle Scholar
  8. [8]
    Vettivel S C, Selvakumar N, Leema N, Lenin A H. Electrical resistivity, wear map and modeling of extruded tungsten reinforced copper composite. Mater Des 56: 791–806 (2016)CrossRefGoogle Scholar
  9. [9]
    Shabani M, Paydar M H, Zamiri R, Goodarzi M, Moshksar M M. Microstructural and sliding wear behavior of SiC-particle reinforced copper matrix composites fabricated by sintering and sinter-forging processes. J Mater Res Tecnol 5(1): 5–12 (2016)CrossRefGoogle Scholar
  10. [10]
    Hausner H H. Modern Developments in Powder Metallurgy. New York: Plenum Press, 1966.CrossRefGoogle Scholar
  11. [11]
    Zhu J, Liu L, Zhao H, Shen B, Hu W. Microstructure and performance of electroformed Cu/nano-SiC composite. Mater Des 28: 1958–1962 (2007)CrossRefGoogle Scholar
  12. [12]
    Fathy A, Shehata F, Abdelhameed M, Elmahdy M. Com-pressive and wear resistance of nanometric alumina reinforced copper matrix composites. Mater Des 36: 100–107 (2012)CrossRefGoogle Scholar
  13. [13]
    Akramifard H R, Shamanian M, Sabbaghian M, Esmailzadeh M. Microstructure and mechanical properties of Cu/SiC metal matrix composite fabricated via friction stir processing. Mater Des 54: 838–844 (2014)CrossRefGoogle Scholar
  14. [14]
    Barmouz M, Asadi P, Givi M K B, Taherishargh M. Investigation of mechanical properties of Cu/SiC composite fabricated by FSP: Effect of SiC particles’ size and volume fraction. Mater Sci Eng A 528: 1740–1749 (2011)CrossRefGoogle Scholar
  15. [15]
    Abd El Aal M I, El Mahallawy N, Shehata F A, Abd El Hameed M, Yoon E Y, Kim H S. Wear properties of ECAP-processed ultrafine grained Al–Cu alloys. Mater Sci Eng A 527: 3726–3732 (2010)CrossRefGoogle Scholar
  16. [16]
    Abd El Aal M I. The effect of the pre-homogenization treatment on the fracture characteristics and wear properties of ECAPed Al-Cu alloys. Mater Sci Eng A 539: 308–323 (2012)CrossRefGoogle Scholar
  17. [17]
    Li J, Wongsa-Ngam J, Xu J, Shan D, Guo B, Langdon T G. Wear resistance of an ultrafine-grained Cu-Zr alloy processed by equal-channel angular pressing. Wear 326–327: 10–19 (2015)CrossRefGoogle Scholar
  18. [18]
    Huang S J, Semenov V I, Shuster L S, Lin P C. Tribological properties of the low-carbon steels with different microstructure processed by heat treatment and severe plastic deformation. Wear 271: 705–711(2011)CrossRefGoogle Scholar
  19. [19]
    Ebrahimi M, Attarilar S, Djavanroodi F, Gode C, Kim H S. Wear properties of brass samples subjected to constrained groove pressing process. Mater Des 63: 531–537(2014)CrossRefGoogle Scholar
  20. [20]
    Abd El Aal M I, Kim H S. Wear properties of high pressure torsion processed ultrafine grained Al–7%Si alloy. Mater Des 53: 373–382 (2014)CrossRefGoogle Scholar
  21. [21]
    Edalati K, Ashida M, Horita Z, Matsui T, Kato H. Wear resistance and tribological features of pure aluminum and Al-Al2O3 composites consolidated by high-pressure torsion. Wear 310(1–2): 83–89 (2014)CrossRefGoogle Scholar
  22. [22]
    Gode C, Yilmazer H,Özdemir I, Todaka Y. Microstructural refinement and wear property of Al-Si-Cu composite subjected to extrusion and high-pressure torsion. Mater Sci Eng A 618: 377–384 (2014)CrossRefGoogle Scholar
  23. [23]
    Abd El Aal M I. Effect of high-pressure torsion processing on the microstructure evolution and mechanical properties of consolidated micro size Cu and Cu-SiC powders. Adv Pow Technol 28(9): 2135–2150 (2017)CrossRefGoogle Scholar
  24. [24]
    Archard J F. Contact and rubbing of flat surfaces. J Appl Phys 24: 981–988 (1953)CrossRefGoogle Scholar
  25. [25]
    Ming H, Yunlong Z, Lili T, Lin S, Jing G, Peiling D. Surface modifying of SiC particles and performance analysis of SiCp/Cu composites. Appl Sur Sci 332: 720–725 (2015)CrossRefGoogle Scholar
  26. [26]
    Hashemi M, Mirdamadi Sh, Rezaie H R. Effect of SiC nano-particles on microstructure and wear behavior of Cu-Ni-W nanocrystalline coating. Elect Acta 138: 224–231(2014)CrossRefGoogle Scholar
  27. [27]
    Safari F, Khosroshah R A, Zolriasatein A. Wear behavior of copper matrix composites reinforced by γ-Cu5Zn8 nanoparticles. Pow Technol 318: 549–557(2017)CrossRefGoogle Scholar
  28. [28]
    Tu J P, Yang Y Z, Wang LY, Ma X C, Zhang X B. Tribological properties of carbon-nanotube-reinforced copper composites. Tribol Lett 10(4): 225–228 (2001)CrossRefGoogle Scholar
  29. [29]
    Hornbogen E. The role of fracture toughness in the wear of metals. Wear 33: 251–259 (1975)CrossRefGoogle Scholar
  30. [30]
    Koch C C. Optimization of strength and ductility in nano-crystalline and ultrafine grained metals. Scripta Materialia 49: 657–66 2 (2003)CrossRefGoogle Scholar
  31. [31]
    Zhang P, An X H, Zhang Z J, Wu S D, Li S X, Zhang Z F, Figueiredo R B, Gao N, Langdon T G. Optimizing strength and ductility of Cu–Zn alloys through severe plastic deformation. Scripta Materialia 67: 871–874 (2012)CrossRefGoogle Scholar
  32. [32]
    Sevim I, Eryurek I B. Effect of fracture toughness on abrasive wear resistance of steels. Mater Des 27: 911–919 (2006)CrossRefGoogle Scholar
  33. [33]
    Zhou L, Liu G, Han Z, Lu K. Grain size effect on wear resistance of a nanostructured AISI52100 steel. Scripta Materialia 58(6): 445–448 (2008)CrossRefGoogle Scholar
  34. [34]
    Wang H, Yang T, Song X, Liu X, Wang X, Wu X. Wear resistance enhancement of bimodal-grained cemented carbide coating. Surf Coat Technol 309: 759–766 (2017)CrossRefGoogle Scholar
  35. [35]
    Akbarpour M R, Alipour S. Wear and friction properties of spark plasma sintered SiC/Cu nanocomposites. Ceram Int 43(16): 13364–13370 (2017)CrossRefGoogle Scholar

Copyright information

© The author(s) 2019

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.

The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.

To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Authors and Affiliations

  1. 1.Mechanical Engineering Department, College of EngineeringPrince Sattam Bin Abdulaziz UniversityWadi AddawaserSaudi Arabia
  2. 2.Mechanical Design & Production Department, Faculty of EngineeringZagazig UniversityZagazigEgypt

Personalised recommendations