Advertisement

Design and study of a pure tire pyrolysis oil (TPO) and blended with Brazilian diesel using Y-Jet atomizer

  • German R. A. Chumpitaz
  • Christian J. R. CoronadoEmail author
  • João A. CarvalhoJr.
  • José C. Andrade
  • Andrés Z. Mendiburu
  • Gabriel M. Pinto
  • Túlio A. de Souza
Technical Paper
  • 44 Downloads

Abstract

This manuscript aims to study the atomization and characterization of tire pyrolysis oil (TPO); thus, Y-Jet atomizers have been designed and manufactured by using an experimental bench, which was specifically built for such a purpose. The droplet size was measured experimentally and compared with the theoretical value obtained with the equation proposed by Wigg. The potential for production of TPO in Brazil from tires discarded for 2016 was approximately 190 million liters and in the world for the same year was 4160 million liters; these values represent an excellent alternative for the energetic use of these oils as well as a good way to valorize the by-products obtained from tire pyrolysis such as char and tire gas. The TPO can be used in combustion processes in pure form or mixed with other renewable or non-renewable fuels, so it is important to study atomization processes that guarantee an excellent quality of combustion. The spray quality generated by atomizing pure TPO and in blends (TPO–diesel) has been quantified by droplet size measurement through the Spraytec Malvern 2007 laser diffraction system, whose main properties have also been measured, such as density, viscosity and surface tension of pure liquid fuels and blends, liquid and gas flow pressure at the atomizer nozzle, and droplet size distributions generated by the atomized jet for different gas/liquid ratio values. The influence of the point where liquid pressure exceeds gas pressure at the atomizer nozzle, as well as the TPO percentage effect on droplet size, is demonstrated, and a comparison of experimental droplet size with the one which had been theoretically calculated by Wigg’s equation is made. The study of the atomization of TPO, pure and blends, allows to know a favorable condition for its burning and provides a suitable destination for discarded tires. For a better characterization of the spray, the atomization cone angle was also measured for all the mixtures.

Keywords

Nozzle Atomization Tire Pyrolysis Compressible fluid 

List of symbols

H

Blending chamber radius (cm)

k

Isentropic coefficient

\(\dot{m}\)

Mass flow (kg/s)

M

Mach number

P

Pressure (Pa)

R

Universal gas constant (kJ/kmol K)

T

Temperature (K)

U

Atomizing air speed (m/s)

ρ

Density (g/cm3)

σ

Surface tension (N/m)

υ

Kinematic viscosity (cSt)

PCI

Lower heating value (kJ/kg)

PCS

Upper heating value (kJ/kg)

DMMD

Mass median diameter (µm)

DSMD

Sauter mean diameter, D32 (µm)

GLR

Gas/liquid (mass) ratio

TPO

Tire pyrolysis oil

Petrobras

Brazilian State Oil Company

Superscripts and subscripts

0

Stagnation conditions

*

Critical properties (Ma = 1)

A

Atomizing air

L

Liquid

Notes

Acknowledgements

Funding for this study was provided by the Fundação de Amparo à Pesquisa do Estado de Minas Gerais, FAPEMIG—Brazil PEMIG (Proc. No. TEC-APQ-01947-14), CAPES—Brazil and CNPq-Brazil (Proc. Nos. 442050/2014-3 and 305965/2016-6).

References

  1. 1.
    Instituto Brasileiro do Meio Ambiente e dos Recursos Naturais Renováveis. Relatório Pneumáticos 2017. Brasília: 2017Google Scholar
  2. 2.
    JATMA. Tyre Industry. 2017Google Scholar
  3. 3.
    Williams PT, Bottrill RP, Cunliffe AM (1998) Combustion of tyre pyrolysis oil. Process Saf Environ Prot 76:291–301.  https://doi.org/10.1205/095758298529650 CrossRefGoogle Scholar
  4. 4.
    Murugan S, Ramaswamy MC, Nagarajan G (2008) A comparative study on the performance, emission and combustion studies of a DI diesel engine using distilled tyre pyrolysis oil-diesel blends. Fuel 87:2111–2121.  https://doi.org/10.1016/j.fuel.2008.01.008 CrossRefGoogle Scholar
  5. 5.
    Murugan S, Ramaswamy MC, Nagarajan G (2008) The use of tyre pyrolysis oil in diesel engines. Waste Manag 28:2743–2749.  https://doi.org/10.1016/j.wasman.2008.03.007 CrossRefGoogle Scholar
  6. 6.
    Murugan S, Ramaswamy C, Nagarajan G (2008) Influence of distillation on performance, emission, and combustion of a DI diesel engine, using tyre pyrolysis oil diesel blends. Therm Sci 12:157–167.  https://doi.org/10.2298/TSCI0801157M CrossRefGoogle Scholar
  7. 7.
    Murugan S, Ramaswamy MC, Nagarajan G (2008) Performance, emission and combustion studies of a DI diesel engine using distilled tyre pyrolysis oil-diesel blends. Fuel Process Technol 89:152–159.  https://doi.org/10.1016/j.fuproc.2007.08.005 CrossRefGoogle Scholar
  8. 8.
    Martínez JD, Lapuerta M, García-Contreras R, Murillo R, García T (2013) Fuel properties of tire pyrolysis liquid and its blends with diesel fuel. Energy Fuels 27:3296–3305.  https://doi.org/10.1021/ef400602e CrossRefGoogle Scholar
  9. 9.
    Sharma A, Murugan S (2013) Investigation on the behaviour of a DI diesel engine fueled with Jatropha methyl ester (JME) and tyre pyrolysis oil (TPO) blends. Fuel 108:699–708.  https://doi.org/10.1016/j.fuel.2012.12.042 CrossRefGoogle Scholar
  10. 10.
    Sharma A, Murugan S (2014) Influence of fuel injection timing on the performance and emission characteristics of a diesel engine fueled with Jatropha methyl ester-tyre pyrolysis oil blend. Appl Mech Mater 592–594:1627–1631.  https://doi.org/10.4028/www.scientific.net/AMM.592-594.1627 CrossRefGoogle Scholar
  11. 11.
    Martínez JD, Rodríguez-Fernández J, Sánchez-Valdepeñas J, Murillo R, García T (2014) Performance and emissions of an automotive diesel engine using a tire pyrolysis liquid blend. Fuel 115:490–499.  https://doi.org/10.1016/j.fuel.2013.07.051 CrossRefGoogle Scholar
  12. 12.
    Koc AB, Abdullah M (2014) Performance of a 4-cylinder diesel engine running on tire oil-biodiesel-diesel blend. Fuel Process Technol 118:264–269.  https://doi.org/10.1016/j.fuproc.2013.09.013 CrossRefGoogle Scholar
  13. 13.
    Ballesteros R, Guillén-Flores J, Martínez JD (2014) Carbonyl emission and toxicity profile of diesel blends with an animal-fat biodiesel and a tire pyrolysis liquid fuel. Chemosphere 96:155–166.  https://doi.org/10.1016/j.chemosphere.2013.10.017 CrossRefGoogle Scholar
  14. 14.
    García-Contreras R, Martínez JD, Armas O, Murillo R, García T (2015) Study of a residential boiler under start-transient conditions using a tire pyrolysis liquid (TPL)/diesel fuel blend. Fuel 158:744–752.  https://doi.org/10.1016/j.fuel.2015.06.046 CrossRefGoogle Scholar
  15. 15.
    Sharma A, Murugan S (2015) Potential for using a tyre pyrolysis oil-biodiesel blend in a diesel engine at different compression ratios. Energy Convers Manag 93:289–297.  https://doi.org/10.1016/j.enconman.2015.01.023 CrossRefGoogle Scholar
  16. 16.
    Sharma A, Murugan S (2016) Experimental evaluation of combustion parameters of a DI diesel engine operating with biodiesel blend at varying injection timings. In: Kumar S, Khanal S, Yadav Y (eds) Proceedings of first international conference on recent advances bioenergy research, New Delhi. Springer, Berlin pp 169–77.  https://doi.org/10.1007/978-81-322-2773-1_13
  17. 17.
    Wang WC, Bai CJ, Lin CT, Prakash S (2016) Alternative fuel produced from thermal pyrolysis of waste tires and its use in a DI diesel engine. Appl Therm Eng 93:330–338.  https://doi.org/10.1016/j.applthermaleng.2015.09.056 CrossRefGoogle Scholar
  18. 18.
    Pilusa TJ (2017) The use of modified tyre derived fuel for compression ignition engines. Waste Manag 60:451–459.  https://doi.org/10.1016/j.wasman.2016.06.020 CrossRefGoogle Scholar
  19. 19.
    Hürdoğan E, Ozalp C, Kara O, Ozcanli M (2017) Experimental investigation on performance and emission characteristics of waste tire pyrolysis oil–diesel blends in a diesel engine. Int J Hydrogen Energy 42:23373–23378.  https://doi.org/10.1016/j.ijhydene.2016.12.126 CrossRefGoogle Scholar
  20. 20.
    Vihar R, Žvar Baškovič U, Seljak T, Katrašnik T (2017) Combustion and emission formation phenomena of tire pyrolysis oil in a common rail Diesel engine. Energy Convers Manag 149:706–721.  https://doi.org/10.1016/j.enconman.2017.02.005 CrossRefGoogle Scholar
  21. 21.
    Sharma A, Murugan S (2017) Effect of blending waste tyre derived fuel on oxidation stability of biodiesel and performance and emission studies of a diesel engine. Appl Therm Eng 118:365–374.  https://doi.org/10.1016/j.applthermaleng.2017.03.008 CrossRefGoogle Scholar
  22. 22.
    Martínez JD, Lapuerta M, García-Contreras R, Murillo R, García T (2013) fuel properties of tire pyrolysis liquid and its blends with diesel fuel. Energy Fuels 27:3296–3305.  https://doi.org/10.1021/ef400602e CrossRefGoogle Scholar
  23. 23.
    Sharma VK, Fortuna F, Mincarini M, Berillo M, Cornacchia G (2000) Disposal of waste tyres for energy recovery and safe environment. Appl Energy 65:381–394.  https://doi.org/10.1016/S0306-2619(99)00085-9 CrossRefGoogle Scholar
  24. 24.
    Williams PT (2013) Pyrolysis of waste tyres: a review. Waste Manag 33:1714–1728.  https://doi.org/10.1016/j.wasman.2013.05.003 CrossRefGoogle Scholar
  25. 25.
    ANIP. Dados de produção 2016:1–2. http://www.anip.com.br/arquivos/producao-vendas.pdf. Accessed 16 Apr 2018
  26. 26.
    Nieto-Márquez A, Atanes E, Morena J, Fernández-Martínez F, Valverde JL (2016) Upgrading waste tires by chemical activation for the capture of SO2. Fuel Process Technol 144:274–281.  https://doi.org/10.1016/j.fuproc.2016.01.009 CrossRefGoogle Scholar
  27. 27.
    Al-Lal AM, Bolonio D, Llamas A, Lapuerta M, Canoira L (2015) Desulfurization of pyrolysis fuels obtained from waste: lube oils, tires and plastics. Fuel 150:208–216.  https://doi.org/10.1016/j.fuel.2015.02.034 CrossRefGoogle Scholar
  28. 28.
    Araújo Costa F, Silva RJ (2005) Pneus inservíveis: análise das leis ambientais vigentes e processos de destinação final adequados. XXV Encontro Nac. Eng. Produção, Porto Alegre, pp 5227–5234Google Scholar
  29. 29.
    Jantaraksa N, Prasassarakich P, Reubroycharoen P, Hinchiranan N (2015) Cleaner alternative liquid fuels derived from the hydrodesulfurization of waste tire pyrolysis oil. Energy Convers Manag 95:424–434.  https://doi.org/10.1016/j.enconman.2015.02.003 CrossRefGoogle Scholar
  30. 30.
    ETRMA. End of life tyres—A valuable resource with growing potential 2011:1–22. http://www.etrma.org/uploads/Modules/Documentsmanager/brochure-elt-2011-final.pdf Accessed 3 July 2016
  31. 31.
    ANIP. Reciclanip. Legislação n.d. http://www.reciclanip.org.br/v3/legislacao
  32. 32.
    SAC PETROBRAS. Unidade de Industrialização do Xisto (SIX): Operações | Petrobras. Unidade Ind Do Xisto n.d. http://www.petrobras.com.br/pt/nossas-atividades/principais-operacoes/refinarias/unidade-de-industrializacao-do-xisto-six.htm. Accessed 7 Dec 2016
  33. 33.
    IBAMA. Relatório de Pneumáticos Resolução CONAMA no 416/09. 2015.  https://doi.org/10.1017/cbo9781107415324.004
  34. 34.
    Martínez JD, Puy N, Murillo R, García T, Navarro MV, Mastral AM (2013) Waste tyre pyrolysis—a review. Renew Sustain Energy Rev 23:179–213.  https://doi.org/10.1016/j.rser.2013.02.038 CrossRefGoogle Scholar
  35. 35.
    Leung DYC, Yin XL, Zhao ZL, Xu BY, Chen Y (2002) Pyrolysis of tire powder: influence of operation variables on the composition and yields of gaseous product. Fuel Process Technol 79:141–155.  https://doi.org/10.1016/S0378-3820(02)00109-1 CrossRefGoogle Scholar
  36. 36.
    Nsaful F, Görgens JF, Knoetze JH (2013) Comparison of combustion and pyrolysis for energy generation in a sugarcane mill. Energy Convers Manag 74:524–534.  https://doi.org/10.1016/j.enconman.2013.07.024 CrossRefGoogle Scholar
  37. 37.
    Sallevelt JLHP, Pozarlik AK, Brem G (2016) Numerical study of pyrolysis oil combustion in an industrial gas turbine. Energy Convers Manag 127:504–514.  https://doi.org/10.1016/j.enconman.2016.09.029 CrossRefGoogle Scholar
  38. 38.
    Harker JH, Backhurst JR (1981) Fuel and energy. Academic Press, CambridgeGoogle Scholar
  39. 39.
    Siva M, Onenc S, Uçar S, Yanik J (2013) Influence of oily wastes on the pyrolysis of scrap tire. Energy Convers Manag 75:474–481.  https://doi.org/10.1016/j.enconman.2013.06.055 CrossRefGoogle Scholar
  40. 40.
    Undri A, Meini S, Rosi L, Frediani M, Frediani P (2013) Microwave pyrolysis of polymeric materials: waste tires treatment and characterization of the value-added products. J Anal Appl Pyrolysis 103:149–158.  https://doi.org/10.1016/j.jaap.2012.11.011 CrossRefGoogle Scholar
  41. 41.
    Roy C, Chaala A, Darmstadt H (1999) Vacuum pyrolysis of used tires end-uses for oil and carbon black products. J Anal Appl Pyrolysis 51:201–221.  https://doi.org/10.1016/S0165-2370(99)00017-0 CrossRefGoogle Scholar
  42. 42.
    Galvagno S, Casu S, Casabianca T, Calabrese A, Cornacchia G (2002) Pyrolysis process for the treatment of scrap tyres: preliminary experimental results. Waste Manag 22:917–923.  https://doi.org/10.1016/S0956-053X(02)00083-1 CrossRefGoogle Scholar
  43. 43.
    Li S-Q, Yao Q, Chi Y, Yan J-H, Cen K-F (2004) Pilot-scale pyrolysis of scrap tires in a continuous rotary kiln reactor. Ind Eng Chem Res 43:5133–5145.  https://doi.org/10.1021/ie030115m CrossRefGoogle Scholar
  44. 44.
    Islam MR, Haniu H, Beg MRA (2008) Liquid fuels and chemicals from pyrolysis of motorcycle tire waste: product yields, compositions and related properties. Fuel 87:3112–3122.  https://doi.org/10.1016/j.fuel.2008.04.036 CrossRefGoogle Scholar
  45. 45.
    Murugan S, Ramaswamy MC, Nagarajan G (2009) Assessment of pyrolysis oil as an energy source for diesel engines. Fuel Process Technol 90:67–74.  https://doi.org/10.1016/j.fuproc.2008.07.017 CrossRefGoogle Scholar
  46. 46.
    Aydin H, Ilkiliç C (2012) Optimization of fuel production from waste vehicle tires by pyrolysis and resembling to diesel fuel by various desulfurization methods. Fuel 102:605–612.  https://doi.org/10.1016/j.fuel.2012.06.067 CrossRefGoogle Scholar
  47. 47.
    Banar M, Akyildiz V, Özkan A, Çokaygil Z, Onay Ö (2012) Characterization of pyrolytic oil obtained from pyrolysis of TDF (Tire Derived Fuel). Energy Convers Manag 62:22–30.  https://doi.org/10.1016/j.enconman.2012.03.019 CrossRefGoogle Scholar
  48. 48.
    Quispe Gonzales CA, Costa F de S, Carvalho Jr JA de. Análise do escoamento em regime subsônico e influência no diâmetro médio das gotas para Injetores de mistura interna tipo Y. 10o Congr. Iberoam. Eng. Mecânica, Porto: 2011Google Scholar
  49. 49.
    Beér JM, Chigier NA (1972) Combustion aerodynamics. Applied Science Publishers, LondonGoogle Scholar
  50. 50.
    Petela R (1982) Analyses of atomization processes. Fuel 61:1135–1137.  https://doi.org/10.1016/0016-2361(82)90199-5 CrossRefGoogle Scholar
  51. 51.
    Suh HK, Park SH, Kim HJ, Lee CS (2009) Influence of ambient flow conditions on the droplet atomization characteristics of dimethyl ether (DME). Fuel 88:1070–1077.  https://doi.org/10.1016/j.fuel.2008.11.018 CrossRefGoogle Scholar
  52. 52.
    Tsai SC, Viers B (1990) Airblast atomization of viscous liquids. Fuel 69:1412–1419.  https://doi.org/10.1016/0016-2361(90)90123-8 CrossRefGoogle Scholar
  53. 53.
    Tsai SC, Ghazimorad K, Viers B (1991) Airblast atomization of micronized coal slurries using a twin-fluid jet atomizer. Fuel 70:483–490.  https://doi.org/10.1016/0016-2361(91)90025-6 CrossRefGoogle Scholar
  54. 54.
    Azevedo Gonçalves C. Desenvolvimento de um sistema compacto de combustão sem chama visível utilizando um injetor blurry para queima de biocombustíveis. Instituto Nacional de Pesquisas Espaciais, 2013Google Scholar
  55. 55.
    Lefebvre AH (1989) Atomization and sprays. Taylor & Francis, RoutledgeGoogle Scholar
  56. 56.
    Broukal J, Hájek J (2011) Validation of an effervescent spray model with secondary atomization and its application to modeling of a large-scale furnace. Appl Therm Eng 31:2153–2164.  https://doi.org/10.1016/j.applthermaleng.2011.04.025 CrossRefGoogle Scholar
  57. 57.
    Cui J, Lai H, Li J, Ma Y (2017) Visualization of internal flow and the effect of orifice geometry on the characteristics of spray and flow field in pressure-swirl atomizers. Appl Therm Eng 127:812–822.  https://doi.org/10.1016/j.applthermaleng.2017.08.103 CrossRefGoogle Scholar
  58. 58.
    Zhou Y, Zhang M, Yu J, Zhu X, Peng J (2010) Experimental investigation and model improvement on the atomization performance of single-hole Y-jet nozzle with high liquid flow rate. Powder Technol 199:248–255.  https://doi.org/10.1016/j.powtec.2010.01.013 CrossRefGoogle Scholar
  59. 59.
    Lacava PT, Pimenta AP, de Carvalho Jr JA (2004) Atomizador tipo “Y-jet”—Projeto, características do spray e combustão. Proc. 10° Brazilian Congr. Therm. Sci. Eng.—ENCIT 2004, Rio de Janeiro, p 11Google Scholar
  60. 60.
    Zeng K, Minh DP, Gauthier D, Weiss-Hortala E, Nzihou A, Flamant G (2015) The effect of temperature and heating rate on char properties obtained from solar pyrolysis of beech wood. Bioresour Technol 182:114–119.  https://doi.org/10.1016/j.biortech.2015.01.112 CrossRefGoogle Scholar
  61. 61.
    Li Z, Wu Y, Yang H, Cai C, Zhang H, Hashiguchi K et al (2013) Effect of liquid viscosity on atomization in an internal-mixing twin-fluid atomizer. Fuel 103:486–494.  https://doi.org/10.1016/j.fuel.2012.06.097 CrossRefGoogle Scholar
  62. 62.
    Ejim CE, Rahman MA, Amirfazli A, Fleck BA (2010) Effects of liquid viscosity and surface tension on atomization in two-phase, gas/liquid fluid coker nozzles. Fuel 89:1872–1882.  https://doi.org/10.1016/j.fuel.2010.03.005 CrossRefGoogle Scholar
  63. 63.
    Watanabe H, Suwa Y, Matsushita Y, Morozumi Y, Aoki H, Tanno S et al (2007) Spray combustion simulation including soot and NO formation. Energy Convers Manag 48:2077–2089.  https://doi.org/10.1016/j.enconman.2007.01.008 CrossRefGoogle Scholar
  64. 64.
    Watanabe H, Suwa Y, Matsushita Y, Morozumi Y, Aoki H, Tanno S et al (2008) Numerical investigation of spray combustion in jet mixing type combustor for low NOx emission. Energy Convers Manag 49:1530–1537.  https://doi.org/10.1016/j.enconman.2007.12.002 CrossRefGoogle Scholar
  65. 65.
    Mullinger PJ, Chigier NA (1974) The design and performance of internal mixing multijet twin fluid atomizers. J Inst Fuel 47:251–261Google Scholar
  66. 66.
    Quispe Gonzales CA (2013) Investigação de injetores tipo Y e efervescentes para a atomização da mistura de glicerina e etanol. UNESP- FEGGoogle Scholar
  67. 67.
    Lacava PT, Carvalho Jr JA, Mcquay MQ. Metodologia para el diseño de atomizadores tipo “Y.” Inf Tecnológica 1998;9Google Scholar
  68. 68.
    Apaza Vásquez R (2011) Desenvolvimento De Um Injetor Centrífugo Dual Para Biocombustíveis Líquidos. Instituto Nacional de Pesquisas Espaciais—INPEGoogle Scholar
  69. 69.
    Spraytec M. Spraytec User Manual 2006:216. http://www.malvern.com/en/support/resource-center/user-manuals/MAN0368EN.aspx. Accessed 7 Mar 2017
  70. 70.
    Jiang G, Zhang Y, Wen H, Xiao G (2015) Study of the generated density of cavitation inside diesel nozzle using different fuels and nozzles. Energy Convers Manag 103:208–217.  https://doi.org/10.1016/j.enconman.2015.06.065 CrossRefGoogle Scholar
  71. 71.
    Song SH, Lee SY (1996) Study of atomization mechanism of gas/liquid mixtures flowing through y-jet atomizers. At Sprays 6:193–209CrossRefGoogle Scholar
  72. 72.
    António NN (2007) Estudo dos mecanismos de despolimerização térmica do Poli(metacrilato de metilo), escolha de solventes compatíveis com PMMA. Instituto Superior Técnico Universidade Técnica de LisboaGoogle Scholar

Copyright information

© The Brazilian Society of Mechanical Sciences and Engineering 2019

Authors and Affiliations

  • German R. A. Chumpitaz
    • 1
  • Christian J. R. Coronado
    • 1
    Email author
  • João A. CarvalhoJr.
    • 2
  • José C. Andrade
    • 3
  • Andrés Z. Mendiburu
    • 2
  • Gabriel M. Pinto
    • 1
  • Túlio A. de Souza
    • 1
  1. 1.Mechanical Engineering Institute – IEMFederal University of Itajubá – UNIFEIItajubáBrazil
  2. 2.Campus of Guaratinguetá – FEGSão Paulo State University – UNESPGuaratinguetáBrazil
  3. 3.Combustion and Propulsion Laboratory – LCPNational Space Research Institute – INPECachoeira PaulistaBrazil

Personalised recommendations