Optimizing layout of wind farm turbines using genetic algorithms in Tehran province, Iran

  • Majid KhanaliEmail author
  • Shahrzad Ahmadzadegan
  • Mahmoud Omid
  • Forough Keyhani Nasab
  • Kwok Wing Chau
Open Access
Original Research


Installation layout of wind turbines plays a prominent role in the design of every wind farm. Thus, the wind farm layout optimization problem is proposed to maximize the total power output with the minimum cost. In this research, Kahrizak region in Tehran province of Iran is selected as a windy region and its real wind speed data are gleaned. Three different scenarios are also considered, with various number of generations and populations for GA parameters, effective distances, and longitude and latitude distances of turbines from each other. Among these scenarios, the best result is obtained for the one in which the longitudinal distance between turbines is greater than the latitudinal distance. By observing the wind rose of Kahrizak region, it is observed that the dominant wind direction of the region is toward the east and south–east. Therefore, by increasing the longitudinal distance of the turbines from each other, the efficiency can be improved and the turbine layout becomes more realistic. In this case, the efficiency rate and normalized cost of turbines are 89.5% and 37.4, respectively, and also 56 turbines are needed. The amounts of efficiency and power output are very convenient for real wind speed data of a region.


Wind farm layout Optimization Genetic algorithm Kahrizak Turbine 


Throughout history, fossil fuels were the primary resources for power production. Despite the efforts in increasing government’s attention to the development and expansion of renewable energy sources, yet fossil fuels are one of the principal sources of power production [1].

However, there is no doubt that some sophisticated circumstances caused striking limitations for fossil fuel consumers, for instances, finite nature of fossil fuels, rising demand for variety of energy sources, sustainable development, awareness of environmental problems from burning fossil fuels, to name a few. Therefore, many countries are paying extra attention to renewable energies.

Recently, the share of renewable energies in the world’s energy portfolio has been constantly increased [2]. Renewable energy resource is often viewed as a good alternative for fossil fuel because of its wide availability and environmentally friendly nature [3]. Although, there are several inexpensive and renewable energy sources in the world, their uses are somewhat low [4]. Among all sources of renewable energies, wind power due to its safety for environment as well as its sustainability, has become more conspicuous in recent years [5]. As the electrical power generated by wind farms is cost-effective, the number of wind farms is noticeably proliferated. Since 1980, from the beginning of wind farms’ development, wind power experienced an unprecedented evolution, increased with almost 1500% within the global wind power installation over the last 15 years, in such a way that at the end of 2015, the total installed capacity reached 432 GW [6].

Wind turbine transforms wind power to electrical power. For a specific large area with high wind speed, to increase power production and decrease costs of installation, wind turbines are grouped within a wind farm. The location of the wind farm, the quality of gearbox, and the shape of wind blades are the factors affecting the conversion efficiency [7]. According to Kenway and Martin [8], changing the blade geometry and structural sizes while maintaining a fixed cost and compatibility with the remainder of turbine system can improve the power output of a wind turbine. Besides, reduced cost of producing wind power can be achieved in different ways, for example, site selection, site layout design, predictive maintenance, and optimal control system design [9]. The installation layout of turbines plays an important role in the design of a wind farm. A non-optimal wind farm layout design can lead to lower than expected wind power capture, increased maintenance costs, and so on [10]. By the ability of turbine’s rotor rotation, wake zone is extracted, which renders negative influence on other turbines [11]. This wake phenomenon, which is generated by upstream turbines, causes speed reduction for downstream ones. Subsequently, the power generated by downstream turbines is lower than upstream ones. Since conventional wind turbines’ layout significantly increases wake effect, optimization of the layout configuration can be a rational strategy to decrease wake effects and also maximize the total power which may be extracted from wind farms. The ‘wind farm layout optimization (WFLO)’ problem is classified under such type of wind turbine layout problem [12].

A lot of research studies have been carried out related to WFLO. There are two major approaches in layout optimization: grid-based approach, and unrestricted layout approach. Grid-based approach is to divide a wind farm into a set of equal-sized cells and place turbines in the center of these cells, while in unrestricted layout approach, turbines are allowed to be placed in any positions within the wind farm [13]. For example, Grady et al. [14] conducted grid-based approach to place wind turbines in a 2 km × 2 km farm and results showed that it was able to place wind turbines in a defined area where the goals of the optimization were maximizing the power output and reducing the cost of implementation. Bazacliu et al. [15] conducted a study on wind farm layout optimization problem (WFLOP). The objective of their study was to determine the optimal placement of wind turbines within the farm. They used a discrete representation of wind farm so that the farm area was decomposed into a set of cells, where each cell can contain only one wind turbine. In that approach, the expected power production was maximized. Chowdhury et al. [16] presented the unrestricted wind farm layout optimization (UWFLO) that addressed critical aspects of optimal wind farm planning using constrained particle swarm optimization (PSO). Reasonable agreement between the wind farm model and the experimental results were obtained. The complex nonlinear optimization problem presented by the wind farm model was effectively solved. They found that an optimal combination of wind turbines with different rotor diameters could improve the wind farm efficiency. Mora et al. [17] applied an evolutionary algorithm (EA) to maximize the profit obtained during the useful life of a wind farm, taking into account a given initial investment. Chen et al. [18] investigated the effect of using wind turbines with different hub height on power output in a small wind farm. Three different wind conditions were analyzed using nested genetic algorithm. Results showed that power output of the wind farm using different hub heights would be increased even when the total number of wind turbines was the same. Moreover, results showed that different hub heights could also improve cost per unit power of a wind farm. Serrano Gonzalez et al. [19] discussed the optimal wind farm configuration problem and proposed EA to optimize the wind farm layout. The algorithm’s optimization process was based on a global wind farm cost model using the initial investment and the present value of the yearly net cash flow during the entire wind farm lifespan. Results showed that the proposed EA was capable of finding the optimum wind farm configuration.

Some other optimization methods have been used for layout optimization of a wind farm. For example, binary particle swarm optimization (BPSO) was used to design optimal wind farm configuration [11]. Ant colony optimization (ACO) algorithm was applied to the design of wind farm layout [20]. Monte Carlo simulation method was used to optimize the layout of a wind farm [21]. Bansal and Farswan [22] presented a solution of WFLO problem using a recent unconventional optimization algorithm, biogeography-based optimization (BBO). Results showed that BBO was capable to outperform conventional methodologies of solving WFLO problem.

This paper attempts to create a GA-based innovative WFLO method taking into account the ability of rotor’s 360 rotation against wind direction and considering the following factors: (1) real wind conditions, (2) selection of wind turbine type and its parameters, (3) number of wind turbines needed for a given wind farm, and (4) wind farm shape. The overall objective of this paper is to significantly develop the grid-based approach by:
  1. 1.

    Developing novel GA-based codes to optimize the wind farm layout as well as reduce the cost per unit power.

  2. 2.

    Implementing the newly developed GA-based codes in a given site under real wind conditions with three scenarios, with different number of generations and population, different effective distances, and different longitudinal and latitudinal distances of turbines from each other.

  3. 3.

    Estimating the annual power production of wind farm and its efficiency.


Materials and methods

Site description and wind condition

The power output of a wind farm is directly affected by wind condition. Most previous research used simplified wind conditions, including three scenarios of single wind speed and direction, single wind speed and different directions, and different wind speeds (8, 12 and 17 m/s) and directions. In this study, real wind data in the Kahrizak region, Tehran province of Iran are used. The data include wind speeds and wind directions for 6 years at 3 h intervals. The detailed information about Kahrizak region is summarized in Table 1. By assessing the wind data of Kahrizak and drawing wind rose of this region (Fig. 1), it is observed that this region with maximum and average wind speed of 15 and 6 m/s, respectively, has a high potential for establishing wind farm and the dominant wind direction of the region over the 6 years is toward east and south–east. Kahrizak region also has a flat terrain and Earth’s topography has a surface roughness property which is considered as a constant number of Z0 = 0.3. Besides, wind turbines that are used in the wind farm have the same model and characteristics. The wind farm chosen in this study is divided into a set of cells, where each cell can contain only one wind turbine that is located in the center of each cell. Two-dimensional Cartesian coordinate system is used to determine the turbine layout and to obtain the optimal response. To prevent severe and dangerous wind arising from the turbulent flow behind wind turbines, the distance between a turbine and its adjacent turbines is considered.
Table 1

Detailed information about Kahrizak region




Kahrizak, Tehran, Iran

Period of record






Height above mean sea level (m)


Fig. 1

Wind rose of Kahrizak region

Cost model

The total cost for installation of a wind farm is modeled in such a way that depends exclusively on the number of installed turbines. To evaluate the installation cost of a wind farm, the equation applied in Mosetti et al. [23] is used in this study (Eq. 1). It is assumed that the non-dimensionalized number of cost/year (normalized cost) for a turbine is one. If a large number of turbines are installed, a maximum cost reduction of \(\frac{1}{3}\) can be considered for each added turbine. Thus, the total cost/year of the whole wind farm or the normalized cost is computed as follows:
$${\text{Normalized cost}} = N\left( {\frac{2}{3} + \frac{1}{3}{\text{e}}^{{ - 0.00174\,{\text{N}}^{2} }} } \right),$$
where N is the number of turbines installed in the wind farm.

Turbine parameters and wake model

Wind farm efficiency and cost per unit power are mostly affected by the selection of wind turbine type. The electrical power extracted from the wind turbine is influenced by direction, intensity and occurrence probability of the wind. Thus, thrust coefficient, hub height and rotor diameter are effective factors on the extracted power. There are different turbine types with different characteristics and powers. For this study, wind turbine AV 928, a production of Avantis, which is a manufacturer from China, is selected. The characteristic curve of turbine AV 928 under 10% turbulence is shown in Fig. 2. The technical characteristics of the turbine are presented in Table 2. The turbine starts producing power at wind speed of 3 m/s and reaches the maximum produced power of 2500 kW at wind speed of 11.6 m/s. After this point, with increasing wind speed up to 25 m/s, turbine’s power output remains constant till the wind speed reaches cutting out wind speed. At higher speeds than 25 m/s, the turbine blades automatically remain inactive to prevent turbine damages.
Fig. 2

Characteristic curve of AV928 wind turbine

Table 2

Technical characteristics of wind turbine AV 928



Rated power (kW)


Cut-in wind speed (m/s)


Rated wind speed (m/s)


Cut-out wind speed (m/s)


Rotor diameter (m)


Swept area (m2)


Hub height (m)


The following equation shows the relationship between the speed and the turbine’s electrical power output considering a quadratic function based on EL-Shimy et al. [24]:
$$P_{i} = \left\{ {\begin{array}{ll} 0 \\ {21401 u_{i}^{2} - 17154u_{i} - 143481} \\ {25000000} \\ \end{array} } \right.\quad \begin{array}{ll} { u_{i} \le 3} \\ {3 \le u_{i} \le 11.6} \\ {11.6 \le u_{i} \le 25} \\ \end{array} ,$$
where Pi is the power output of ith wind turbine, and ui is the wind speed in front of ith wind turbine. When the ith wind turbine is not affected by any wake, ui will be the velocity of the free stream. When the ith wind turbine is affected by a wake, ui will be the wind speed caused by the wake [13].
The wake model used in this study is the one proposed by Jensen (1983) in describing the wind behavior of a wake, as shown in Fig. 3. Assuming that the momentum is conserved in the wake, the wind velocity of a downstream turbine is as follows [25]:
$$u = u_{0} \left[ {1 - \frac{2a}{{\left( {1 + \alpha \left( {\frac{x}{r}} \right)^{2} } \right)^{2} }}} \right],$$
where u is the wind velocity of the downstream turbine, u0 is the free flow velocity, x is the distance from the upstream turbine, a is the axial induction factor, α is the entrainment constant, and r is the downstream rotor radius. The relationship between r and the turbine radius rr is computed by Eq. (4) [25]:
$$r = r_{r} \sqrt {\frac{1 - a}{1 - 2a}} .$$
Fig. 3

Schematic diagram of Jensen’s wake model [14]

The axial induction factor can be computed by the turbine thrust coefficient CT, which is given by Eq. (5) [14]:
$${\text{C}}_{\text{T}} = { 4 }\alpha \, \left( { 1- \, \alpha } \right),$$
where α is the entrainment constant that can be varied, depending on the characteristics of local terrain and weather conditions, and is determined by Eq. (6) [14]:
$$\alpha = \frac{0.5}{{\ln \left( {\frac{h}{{z_{0} }}} \right) }},$$
where h represents the hub height, and z0 is the terrain surface roughness. Assuming that there are multiple wakes, the kinetic energy wastage is equal to sum of the energy defects. Thus, for N downstream turbines, the velocity can be expressed by Eq. (7) [26]:
$$u = u_{0} \left[ {1 - \sqrt {\mathop \sum \limits_{i = 1}^{N} \left( {1 - \frac{u}{{u_{0} }}} \right)^{2} } } \right].$$
When investigating wind in different directions, it is noted that if wind blows from the right direction, only the last column is subjected to direct wind (Fig. 4a) and if the wind direction is inclined, both the first row and the last column are exposed to direct wind (Fig. 4b).
Fig. 4

Turbines which are exposed to wind’s speed and angle. a The last column is exposed to the initial wind speed. b The first row and the last column are exposed to the initial wind speed

It is also worth noting that the wake effect varies for different wind angles. An innovative algorithm is developed based on the angle of two turbines from each other and the angle of wind collision with the first turbine (Fig. 5).
Fig. 5

Pattern of wake effect

According to Fig. 5, this pattern is used to determine whether the turbine T is influenced by the wake effect of turbine T1. The wake effect generated by the wind blown from turbine T1 makes angle α with wind direction. On the other hand, two turbines T and T1 create an angle β with each other. According to Eq. (8), the wake effect of turbine T1 affects turbine T.
$${\text{angle}} - \alpha < \beta < {\text{angle}} + \alpha .$$
If Eq. (8) is not realized, turbine T will not be influenced by the wake effect of turbine T1. To implement this and codify it in MATLAB software, specific items should be considered. Therefore, the terrain is divided into four coordinate intervals, and considered as radians (Fig. 6).
Fig. 6

Terrain division into four coordinate intervals

In this study, to determine the small range of wind direction, the interval between 0 and π/2 is selected (0 ≤ angle < π/2) and then generalized to three other intervals. Besides, to determine the turbine affected by the wake of upstream turbine, the wake of the nearest turbine is considered and this assumption is precisely generalized to other ones. The impact criterion of a turbine from the wake of the upstream turbine is the distance. Thus, the effective distance (ED) is innovatively considered six times as much as the average longitudinal and latitudinal distance between the turbines (Eq. 9)
$${\text{effective distance}} = 6 \times \left( {\frac{x + y}{2}} \right),$$
where x and y are the longitudinal and latitudinal distance of the turbines, respectively.

Optimization method

Overview of genetic algorithm

Wind farm layout optimization (WFLO) problem is a discrete problem that, due to its complexity, for example, non-uniform wind speeds with variable directions, cannot be solved using classical methods and have to be solved by intelligent algorithms. Among all intelligent algorithms that have been used in WFLO problem, GA is the best one. It is actually the most famous type of evolutionary algorithms due to its specific properties to yield a set of preliminary solutions, search for optimal solution from amongst the proper ones and repeat this process to achieve the optimum solution [27]. GA is a heuristic solution-search or optimization technique, originally motivated by the Darwinian principle of natural genetic and evolution mechanisms observed in nature. GA was first proposed by John Holland [28] as a means of finding good solutions to problems that were otherwise computationally intractable. Holland’s Schema Theorem and the related building block hypothesis provided a theoretical and conceptual basis for the design of efficient GA that was successfully applied to a wide range of practical problems in science, engineering and industry [29, 30, 31, 32, 33, 34]. This algorithm is based on artificial intelligence and is a population-based method which improves the solutions during different iterations and contributes to the evolutionary process of solutions. GA includes following stages:

In the first stage, a random set of solutions is created. Each solution is called a chromosome and each chromosome is made of smaller parts named as gene. In GA, these set of solutions are called population. After the formation of each generation, it must be specified to what extent the chromosomes of the next generation are close to optimal solution. This is known as fitness function. The best solutions for each generation could be defined using fitness function. In the next stage, we create a new generation using a series of GA operators. These operators include selection, crossover and mutation. Creation of a new generation is accomplished through reproduction, for which we need parents. The parents are determined from current population by a selection operator. This operator selects the best cases from the chromosomes existing in a population to create a new generation. With the fusion of two chromosomes, a new member will be created. These two genetic chromosomes play the role of the parents and the new member plays the role of the child. The most common types of crossovers contain: one-point crossover, two-point crossover, and uniform crossover. Mutation operator uses only one parent to make a child. This is realized through slight changes in initial strings of chromosomes. Finally, after the creation of a new generation, we select the best solution (chromosome) of this generation and compare it with best present solution. This process (making generation) continues till the algorithm reaches its final position, e.g., the optimal solution is found or the stopping criterion for the algorithm is brought to an end.

Process of optimization

GA coding is implemented in MATLAB to search the optimal layout of a given wind farm. The coding is sub-divided into several sections as follows:

Insert data: in this section, data are introduced as input to the algorithm, e.g., terrain dimensions, wind turbine characteristics, wind characteristics, and the number of turbines.

Problem definition: in this section, objective functions including fitness and cost functions related to this problem are determined (Eq. 10). The fitness function in this study is to optimize the wind farm layout, and the cost function is to minimize the total cost of the produced power.
$${\text{Objective}} = \frac{\text{Normalized cost}}{{P_{\text{tot}} }} = \frac{{N\left( {\frac{2}{3} + \frac{1}{3}{\text{e}}^{{ - 0.00174\,{\text{N}}^{2} }} } \right)}}{{\sum\nolimits_{i = 1}^{i = N} {P_{i} } }}.$$

Parameter setting: in this section, parameters related to reproduction, such as population size, max_iter, percentages of children produced by crossover and by mutation are determined.

Initialization: in this section, an empty matrix for individuals (chromosomes) is defined. In this study, as initial population, GA makes a m × n binary matrix including different individuals representing wind farm layouts, where m is the total number of individuals in one generation and n is the length of each individual representing potential positions of wind turbines. The values of m and n are defined at the beginning of optimization. In each individual, 1 means there is a turbine in the cell and 0 means there is no turbine in it. After that, a random solution should be created for the total population. Members of the population are then sorted and ultimately the best solutions are found and saved.

GA main loop: in the main loop of the algorithm, main computations of the algorithm are performed to determine the optimal solution for the problem. In this section, the algorithm generates new children based on crossover and mutation operations. The two operators of crossover and mutation are written as a function in this section.

Crossover: this section includes properties related to crossover operator. The present paper applies the single-point crossover method and the crossover rate is considered 0.9.

Mutation: this part includes properties related to mutation operator. The present paper applies the mutation method in chromosomes with real variable and the mutation rate is considered 0.1.

Results: results of the algorithm, including the best solution, the best fitness, computation time, figures representing the number of iteration, fitness, etc., are coded in this section.

Figure 7 illustrates the flowchart of the methodology followed in this study for solving WFLO problem using genetic algorithm.
Fig. 7

Flowchart of wind farm layout optimization by genetic algorithm

Results and discussion

Optimal turbine layout of the studied region is presented using three scenarios: (1) different population and generations, (2) different effective distances, and (3) different longitudinal and latitudinal distance of the turbines from one another.

Optimization results with different numbers of population and generations

Layout optimization is performed in MATLAB software for Kahrizak region with three different numbers of generations and population: (1) generation = 500 and population = 250; (2) generation = 500 and population = 500; and (3) generation = 1000 and population = 500. The optimization results based on different generations and population are presented in Table 3. According to Table 3, changes in the number of generations and population do not have a significant impact on wind farm efficiency, but increases the total power. It must be mentioned that wind farm efficiency is defined as the ratio of the total energy extracted by the wind farm having N turbines and N times the energy extracted by an isolated turbine with the same undisturbed wind [23]. Figure 8 shows the visual representation of the optimal layout obtained using three different number of generations and population. As can be seen, three layouts are approximately similar to each other. Considering the turbine’s 360° rotation, the turbine dispersion at the outer edge of the wind farm to its center is logical and justifiable. Convergence diagrams of the GA for three different generations and population are presented in Fig. 9.
Table 3

Optimization results of Kahrizak region using different generations and population


Generation = 500 population = 250

Generation = 500 population = 500

Generation = 1000 population = 250

Fitness value




Total power (kW/year)




Normalized cost




Efficiency (%)




Number of turbines




Fig. 8

Optimal layout of turbines for the studied wind farm, considering different generations and population. a Generations = 500 and population = 250, b generations = 500 and population = 500, and c generations = 1000 and population = 500

Fig. 9

Convergence diagrams of genetic algorithm for three different generations and population. a Generations = 500 and population = 250, b generations = 500 and population = 500, and c generations = 1000 and population = 500

Optimization results with different effective distances

In this scenario, the distance between adjacent turbines is changed from 6 to 20 times as much as the average longitudinal and latitudinal distance of turbines from one another. Then, the coding is executed with generations and population of 1000 and 500, respectively. The numerical results are summarized in Table 4. Based on the results, by increasing the effective distance, the efficiency has been decreased from 88.72 to 88.41%. Also, total output power is decreased from 9422.4 to 9205.2 kW/year. These results reflect that increasing the effective distance does not have a positive effect on results and highlight that the distance considered (six times as much as the average longitudinal and latitudinal distance) is logical. Figure 10 shows the visual representation of the optimal layout obtained for the effective distance 20. Convergence diagram of GA for effective distance 20 is presented in Fig. 11.
Table 4

Comparison of results with different effective distance in Kahrizak region


\({{ED}} = 6 \times \left( {\frac{{{{x}} + {{y}}}}{2}} \right)\)

\({{ED}} = 20 \times \left( {\frac{{{{x}} + {{y}}}}{2}} \right)\)

Fitness value



Total power (kW/year)



Normalized cost



Efficiency (%)



Number of turbines



Fig. 10

Optimal layout obtained for the effective distance \(20 \times \left( {\frac{{{\mathbf{x}} + {\mathbf{y}}}}{2}} \right)\)

Fig. 11

Convergence diagram of genetic algorithm for effective distance 20

Optimization results with different longitudinal and latitudinal distance of turbines from one another

Given equal number of generations and population and changing the distance x and y, the numerical results are as presented in Table 5. Numerical results show that changing the longitudinal distance (x) and latitudinal distance (y) have a positive effect on the wake effect and significant increase of power output obtained from this scenario confirms it. Figure 10 shows the visual representation of the optimal layouts obtained from this scenario. According to Fig. 12, because the dominant wind direction in this region is toward the east and south–east, thus by increasing the longitudinal distance (x) of the turbines from one another, the density of the turbines in the left hand of the upper rows and the right hand of the lower rows is more than the other sides of the wind farm. In fact, by increasing the longitudinal distance of the turbines from each other, the wake effect on the downstream turbines is decreased, which results in higher efficiency. Convergence diagram of GA with different longitudinal and latitudinal distance of the turbines from one another is shown in Fig. 13.
Table 5

Optimization results with different longitudinal and latitudinal distance of turbines from one another in Kahrizak region


X = 372.8

Y = 186.4

X = 186.4

Y = 372.8

Fitness value



Total power (kW/year)



Normalized cost



Efficiency (%)



Number of turbines



Fig. 12

Optimal layout with changing longitudinal and latitudinal distance of turbines from one another. a X = 372.8 and Y = 186.4, b X = 186.4 and Y = 372.8

Fig. 13

Convergence diagram of genetic algorithm with different longitudinal and latitudinal distance of the turbines from one another

According to results from this study, it can be concluded that GA is capable of optimizing the turbine layout so that the energy cost is reduced compared to that of the traditional layout. These results can be confirmed by some similar studies. For example, Pillai et al. [35] conducted a case study wherein they explored the application of a wind farm layout evaluation function and layout optimization framework to Middelgrunden wind farm in Denmark using genetic algorithm. Results showed that this optimization algorithm was capable of identifying layouts with reduced levelized energy cost compared to the existing layout while still considering the specific conditions and constraints of this site and those typical of future projects. In another study, Rajper and Amin [36] conducted a GA-based study to find out the optimal solution for the wind turbine micro-sightings. The site that was under consideration for greener solutions of the problem was Gharo-Sindh, Pakistan. The basic objective of the study was to find the most optimal solution for cost per unit power. Results showed that GA was able to optimize the value of fitness function. Parada et al. [37] proposed an approach to solve the WFLO problem based on a Gaussian wake model using GA. The proposed approach minimized the annual cost of energy of a wind farm. The application of the proposed approach yielded higher annual generation and a lower computational time for all wind scenarios under study.


Given the relatively low cost of electrical power generated by wind farms, the number of installed wind farms is increasing every year. The installation layout of turbines plays an important role in the design of a wind farm. Thus, wind farm layout optimization (WFLO) problem is proposed so as to maximize the total power output with minimum cost. This study introduces innovative GA-based codes considering the rotor’s 360° rotation ability against the wind direction to make the optimization of wind turbine layout closer to reality. In this study, by selecting the Kahrizak region as a windy region and choosing a turbine named “AV980”, three different scenarios, including different numbers of generations and population, different effective distances, and different longitudinal and latitudinal distance of turbines from one another are studied. Among three scenarios, the best result is obtained for a scenario wherein the longitudinal distance is greater than the latitudinal distance. By observing the wind rose of Kahrizak region, it is found that the dominant wind direction of the region is toward the east and south–east. Therefore, increasing the longitudinal distance of the turbines from one another will improve the efficiency and also make the turbine layout more realistic in the terrain. In this case, the efficiency and normalized cost of turbines are 89.5% and 37.4, respectively, and also 56 turbines are needed. Total power is computed annually over 10.1 MW. These amounts of efficiency and power output are very suitable based on real data of a region.



The authors would like to thank the University of Tehran for funding the project numbered 05-6-324030.


  1. 1.
    Bhowmik, C., Bhowmik, S., Ray, A., Pandey, K.M.: Optimal green energy planning for sustainable development: a review. Renew. Sustain. Energy Rev. 71, 796–813 (2017)CrossRefGoogle Scholar
  2. 2.
    Qolipour, M., Mostafaeipour, A., Rezaei, M.: A mathematical model for simultaneous optimization of renewable electricity price and construction of new wind power plants (case study: Kermanshah). Int. J. Energy Environ. Eng. 9, 71–80 (2018)CrossRefGoogle Scholar
  3. 3.
    Fazelpour, F., Soltani, N., Rosen, M.A.: Wind resource assessment and wind power potential for the city of Ardabil, Iran. Int. J. Energy Environ. Eng. 6, 431–438 (2015)CrossRefGoogle Scholar
  4. 4.
    Asl, S.J., Banafsheh, M.R., Dinpashoh, Y., Esmaeilpour, M., Mohammadi, K., Khorshiddoust, A.M.: Assessing wind energy potential in Kurdistan province, Iran. Int. J. Energy Environ. Eng. 5, 100–111 (2014)CrossRefGoogle Scholar
  5. 5.
    Keyhani, A., Ghasemi-Varnamkhasti, M., Khanali, M., Abbaszadeh, R.: An assessment of wind energy potential as a power generation source in the capital of Iran, Tehran. Energy 35, 188–201 (2010)CrossRefGoogle Scholar
  6. 6.
    Gentils, T., Wang, L., Kolios, A.: Integrated structural optimization of offshore wind turbine support structures based on finite element analysis and genetic algorithm. Appl. Energy 199, 187–204 (2017)CrossRefGoogle Scholar
  7. 7.
    Hall, J.F., Meeklenborg, C.A., Chen, D., Pratap, S.B.: Wind energy conversion with a variable-ratio gearbox: design and analysis. Renew. Energy 36, 1075–1080 (2011)CrossRefGoogle Scholar
  8. 8.
    Kenway, G., Martin, J.: Aero structural shape optimization of wind turbine blades considering site-specific winds. In: 12th AIAA/ISSMO Multidisciplinary Analysis and Optimization Conference. Toronto, Canada (2008)Google Scholar
  9. 9.
    Wiser, R., Bolinger, M.: Annual report on US wind power installation, cost, and performance trends: 2006, pp. 32. NREL Report No. TP-500-41435; DOE/GO-102007-2433. (2007)
  10. 10.
    Kusiak, A., Song, Z.: Design of wind farm layout for maximum wind energy capture. Renew. Energy 35, 685–694 (2010)CrossRefGoogle Scholar
  11. 11.
    Pookpunt, S., Ongsakul, W.: Design of optimal wind farm configuration using a binary particle swarm optimization at Huasai district, Southern Thailand. Energy Conserv. Manage. 108, 160–180 (2016)CrossRefGoogle Scholar
  12. 12.
    Patel, J., Saysani, V., Patel, V., Patel, R.: Layout optimization of a wind farm to maximize the power output using enhanced teaching learning based optimization technique. J. Clean. Prod. 158, 81–94 (2017)CrossRefGoogle Scholar
  13. 13.
    Chen, Y., Li, H., He, B., Wang, P., Jin, K.: Multi-objective genetic algorithm based innovative wind farm layout optimization method. Energy Conserv. Manage. 105, 1318–1327 (2015)CrossRefGoogle Scholar
  14. 14.
    Grady, S.A., Hussaini, M.Y., Abdullah, M.M.: Placement of wind turbines using genetic algorithms. Renew. Energy 30, 259–270 (2005)CrossRefGoogle Scholar
  15. 15.
    Bazaclui, G., Lazaroiu, G.C., Dumbrava, V.: Design of wind farm layout for maximum wind energy capture. UPB Sci. Bull. Ser. C 77, 269–276 (2015)Google Scholar
  16. 16.
    Chowdhury, S., Zhang, J., Messac, A., Castillo, L.: Unrestricted wind farm layout optimization (UWFLO): investigating key factors influencing the maximum power generation. Renew. Energy 38, 16–30 (2012)CrossRefGoogle Scholar
  17. 17.
    Mora, J.C., Baron, J.C., Santos, J.R., Payan, M.B.: An evolutive algorithm for wind farm optimal design. Neurocomputing 70, 2651–2658 (2007)CrossRefGoogle Scholar
  18. 18.
    Chen, Y., Li, H., Jin, K., Song, Q.: Wind farm layout optimization using genetic algorithm with different hub height wind turbines. Energy Conserv. Manage. 70, 56–65 (2013)CrossRefGoogle Scholar
  19. 19.
    Gonzalez, J.S., Rodriguez, A.G.G., Mora, J.C., Santos, J.R., Payan, M.B.: Optimization of wind farm turbines layout using an evolutive algorithm. Renew. Energy 35, 1671–1681 (2010)CrossRefGoogle Scholar
  20. 20.
    Eroglu, Y., Seckiner, S.U.: Design of wind farm layout using ant colony algorithm. Renew. Energy 44, 53–62 (2012)CrossRefGoogle Scholar
  21. 21.
    Marmidis, G., Lazarou, S., Pyrgioti, E.: Optimal placement of wind turbines in a wind park using Monte Carlo simulation. Renew. Energy 33, 1455–1460 (2008)CrossRefGoogle Scholar
  22. 22.
    Bansal, J.C., Farswan, P.: Wind farm layout using biogeography based optimization. Renew. Energy 107, 386–402 (2017)CrossRefGoogle Scholar
  23. 23.
    Mosetti, G., Poloni, C., Diviacco, B.: Optimization of wind turbine positioning in large wind farms by means of a genetic algorithm. J. Wind Eng. Ind. Aerodyn. 51, 105–116 (1994)CrossRefGoogle Scholar
  24. 24.
    EL-Shimy, M.: Optimal site matching of wind turbine generator: case study of the Gulf of Suez region in Egypt. Renew. Energy 35, 1870–1878 (2010)CrossRefGoogle Scholar
  25. 25.
    Changshui, Z., Guangdong, H., Jun, W.: A fast algorithm based on the submodular property for optimization of wind turbine positioning. Renew. Energy 36, 2951–2958 (2011)CrossRefGoogle Scholar
  26. 26.
    Dupont, B., Cagan, J., Moriarty, P.: An advanced modeling system for optimization of wind farm layout and wind turbine sizing using a multi-level extended pattern search algorithm. Energy 106, 802–814 (2016)CrossRefGoogle Scholar
  27. 27.
    Nazari, H., Kazemi, A., Hashemi, M.H., Sadat, M.M., Nazari, M.: Evaluating the performance of genetic and particle swarm optimization algorithms to select an appropriate scenario for forecasting energy demand using economic indicators: residential and commercial sectors of Iran. Int. J. Energy Environ. Eng. 6, 345–355 (2015)CrossRefGoogle Scholar
  28. 28.
    Holland, J.H.: Adaptation in Natural and Artificial Systems. University of Michigan Press, Ann Arbor (1975)Google Scholar
  29. 29.
    Kazemi, S.M.R., Bidgoli, B.M., Shamshirband, S., Karimi, S.M., Ghorbani, M.A., Chau, K.W., KazemPour, R.: Novel genetic-based negative correlation learning for estimating soil temperature. Eng. Appl. Comput. Fluid Mech. 12(1), 506–516 (2018)Google Scholar
  30. 30.
    Wu, C.L., Chau, K.W.: A flood forecasting neural network model with genetic algorithm. Int. J. Environ. Pollut. 28(3–4), 261–273 (2006)CrossRefGoogle Scholar
  31. 31.
    Cheng, C.T., Wu, X.Y., Chau, K.W.: Multiple criteria rainfall-runoff model calibration using a parallel genetic algorithm in a cluster of computer. Hydrol. Sci. J. 50(6), 1069–1087 (2005)CrossRefGoogle Scholar
  32. 32.
    Chau, K.W., Albermani, F.: Knowledge-based system on optimum design of liquid retaining structures with genetic algorithms. J. Struct. Eng. ASCE 129(10), 1312–1321 (2003)CrossRefGoogle Scholar
  33. 33.
    Chau, K.W.: A two-stage dynamic model on allocation of construction facilities with genetic algorithm. Autom. Constr. 13(4), 481–490 (2004)MathSciNetCrossRefGoogle Scholar
  34. 34.
    Wang, W.C., Cheng, C.T., Chau, K.W., Xu, D.M.: Calibration of Xinanjiang model parameters using hybrid genetic algorithm based fuzzy optimal model. J. Hydroinform. 14(3), 784–799 (2012)CrossRefGoogle Scholar
  35. 35.
    Pillai, A.C., Chick, J., Khorasanchi, M., Barbouchi, S., Johanning, L.: Application of an offshore wind farm layout optimization methodology at Middelgrunden wind farm. Ocean Eng. 139, 287–297 (2017)CrossRefGoogle Scholar
  36. 36.
    Rajper, S., Amin, I.J.: Optimization of wind turbine micrositing: a comparative study. Renew. Sustain. Energy Rev. 16, 5485–5492 (2012)CrossRefGoogle Scholar
  37. 37.
    Parada, L., Herrera, C., Flores, P., Parada, V.: Wind farm layout optimization using a Gaussian-based wake model. Renew. Energy 107, 531–541 (2017)CrossRefGoogle Scholar

Copyright information

© The Author(s) 2018

Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (, which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Authors and Affiliations

  • Majid Khanali
    • 1
    Email author
  • Shahrzad Ahmadzadegan
    • 1
  • Mahmoud Omid
    • 1
  • Forough Keyhani Nasab
    • 2
  • Kwok Wing Chau
    • 3
  1. 1.Department of Agricultural Machinery Engineering, Faculty of Agricultural Engineering and Technology, College of Agriculture and Natural ResourcesUniversity of TehranKarajIran
  2. 2.Department of Biosystem Engineering, Faculty of Agriculture and Natural ResourcesUniversity of Mohaghegh ArdabiliArdabilIran
  3. 3.Department of Civil and Environmental EngineeringHong Kong Polytechnic UniversityHung HomHong Kong

Personalised recommendations