Advertisement

Effect of thermal regeneration of diatomite adsorbent on its efficacy for removal of dye from water

  • H. Aguedal
  • A. Iddou
  • A. Aziz
  • A. Shishkin
  • J. Ločs
  • T. Juhna
Original Paper

Abstract

Reduction in adsorption capacities of adsorbents is limiting of its wider application for water treatment. In this study, we developed a new approach for recycling diatomite to be used adsorbent. The laser scattering particle size analyzer, X-ray diffraction, scanning electron microscopy/energy-dispersive X-ray and Brunauer–Emmett–Teller analysis were used to evaluate the structural characteristics of treated samples. The adsorption efficacy of raw and heated diatomite at 300, 600 and 900 °C for textile dyestuff removal from wastewater was investigated. The characterization results show insignificant changes except some deconstructions were occurred after treatment at 900 °C. The maximum adsorption capacities were obtained at pH 2 and adsorbent dosage of 4 g L−1. The required time to reach the equilibrium was 30 min, and diatomite treated at 600 °C is acted as an excellent adsorbent. The kinetic studies were better described by the pseudo-second-order kinetic model. The isotherms experimental data showed that the adsorption of dye onto raw diatomite, DH300 and DH600 follows the Brunauer–Emmett–Teller isotherm model, but its adsorption onto DH900 conforms well to Freundlich isotherm model. Recycling of diatomite using thermal treatment was useful. At 600 °C which is considered the best regeneration temperature, the adsorbed dye was completely despaired, and around 73% was restored after three regeneration cycles.

Keywords

Diatomite Dye adsorption Thermal regeneration Wastewater purification 

List of symbols

Ci

Initial concentration of R-ETL dye (mg L−1)

Ce

Equilibrium concentration of R-ETL dye (mg L−1)

Qe

Adsorbed quantity of R-ETL dye (mg g−1)

V

Volume of solution (L)

W

Amount of adsorbents (g)

R

Removal efficiency of R-ETL dye (%)

t

Time (min)

Qt

Amount of R-ETL dye adsorbed at time t (mg g−1)

k1p

Pseudo-first-order kinetic model constant (min−1)

k2p

Pseudo-second-order kinetic model constant (g mg−1 h−1)

kp

Intra-particle diffusion kinetic model constant (g mg−1 min−0.5)

Ct

Concentration at time t (mg L−1)

D

Intra-particle diffusion coefficient (m2 s−1)

r

Particle radius assuming spherical geometry (m)

KF

Freundlich constant (mg g−1) (L g−1)1/n

1/n

Freundlich exponent

KL

Langmuir isotherm constant (L mg−1)

Qmax

Maximum adsorption capacity of R-ETL dye (mg g−1)

DDR

Dubinin–Radushkevich isotherm constant (mol2 kJ−2)

T

Temperature (K)

R

Ideal gas constant (J K−1 mol−1)

CBET

BET adsorption isotherm constant (L/mg)

Cs

Saturation concentration of R-ETL dye (mg L−1)

Qs

Monolayer adsorption capacity (mg g−1)

RMES

Root-mean-squared error

qeexp

Observed amounts of R-ETL dye adsorbed (mg g−1)

qecal

Predicted amounts of R-ETL dye adsorbed (mg g−1)

N

Number of experimental measurements

Cu

Coefficients of uniformity

D10

Intercepts for 10% of the cumulative mass

D60

Intercepts for 60% of the cumulative mass

Notes

Acknowledgements

The authors gratefully acknowledge the financial support provided by the Algerian Ministry of Superior Education and Scientific Research (PNE Program No. 682, Code 16/70682). The authors would like to acknowledge the assistance provided by Mr Kristaps Rubenis, Ms Inga Dušenkova and Ms Valentīna Stepanova, from Rudolfs Cimdins Riga Biomaterials Innovations and Development Center, Institute of General Chemical Engineering, Faculty of Materials Science and Applied Chemistry, Riga Technical University, Latvia, respectively, for SEM micrographs, laser scattering particle size analyzes and BET analyzes. In the end the authors would like to dedicate this work for Prof. Ouali Mohand Said, from Abdelhamid Ibn Badis University, Mostaganem (Algeria), may he rest in peace.

References

  1. Abidi N, Errais E, Duplay J et al (2015) Treatment of dye-containing effluent by natural clay. J Clean Prod 86:432–440.  https://doi.org/10.1016/j.jclepro.2014.08.043 CrossRefGoogle Scholar
  2. Akar ST, Özcan AS, Akar T et al (2009) Biosorption of a reactive textile dye from aqueous solutions utilizing an agro-waste. Desalination 249:757–761.  https://doi.org/10.1016/j.desal.2008.09.012 CrossRefGoogle Scholar
  3. Al-Ghouti M, Khraisheh MAM, Ahmad MNM, Allen S (2005) Thermodynamic behaviour and the effect of temperature on the removal of dyes from aqueous solution using modified diatomite: A kinetic study. J Colloid Interface Sci 287:6–13.  https://doi.org/10.1016/j.jcis.2005.02.002 CrossRefGoogle Scholar
  4. Aziz A, Ouali MS, Elandaloussi EH et al (2009) Chemically modified olive stone: a low-cost sorbent for heavy metals and basic dyes removal from aqueous solutions. J Hazard Mater 163:441–447.  https://doi.org/10.1016/j.jhazmat.2008.06.117 CrossRefGoogle Scholar
  5. Belala Z, Jeguirim M, Belhachemi M et al (2011) Biosorption of basic dye from aqueous solutions by Date Stones and Palm-Trees Waste: kinetic, equilibrium and thermodynamic studies. DES 271:80–87.  https://doi.org/10.1016/j.desal.2010.12.009 CrossRefGoogle Scholar
  6. Bhatti HN, Nausheen S (2014) Equilibrium and kinetic modeling for the removal of Turquoise Blue PG dye from aqueous solution by a low-cost agro waste. Desalin Water Treat.  https://doi.org/10.1080/19443994.2014.927799 Google Scholar
  7. Bisinella F, Nivaldo A, Eduardo C et al (2016) Monolayer–multilayer adsorption phenomenological model: kinetics, equilibrium and thermodynamics. Chem Eng J 284:1328–1341.  https://doi.org/10.1016/j.cej.2015.09.085 CrossRefGoogle Scholar
  8. Chen J, Pan X, Chen J (2013) Regeneration of activated carbon saturated with odors by non-thermal plasma. Chemosphere 92:725–730.  https://doi.org/10.1016/j.chemosphere.2013.04.014 CrossRefGoogle Scholar
  9. de Sales PF, Magriotis ZM, de LS Rossi MA et al (2013) Study of chemical and thermal treatment of kaolinite and its influence on the removal of contaminants from mining effluents. J Environ Manag 128:480–488.  https://doi.org/10.1016/j.jenvman.2013.05.035 CrossRefGoogle Scholar
  10. Devi S, Murugappan A, Rajesh Kannan R (2015) Sorption of reactive blue 19 onto freshwater algae and seaweed. Desalin Water Treat 54:2611–2624.  https://doi.org/10.1080/19443994.2014.902333 CrossRefGoogle Scholar
  11. Djafer A, Kouadri Moustefai S, Iddou A, Si Ali B (2014) Study of bimacid dye removal from aqueous solution: a comparative study between adsorption on pozzolana, bentonite, and biosorption on immobilized anaerobic sulfate-reducer cells. Desalin Water Treat 52:7723–7732.  https://doi.org/10.1080/19443994.2013.833866 CrossRefGoogle Scholar
  12. Djilani C, Zaghdoudi R, Djazi F et al (2015) Adsorption of dyes on activated carbon prepared from apricot stones and commercial activated carbon. J Taiwan Inst Chem Eng 53:112–121.  https://doi.org/10.1016/j.jtice.2015.02.025 CrossRefGoogle Scholar
  13. Dubinin MM, Radushkevich LV (1947) The equation of the characteristic curve of the activated charcoal. Proc Acad Sci USSR Phys Chem Sect 55:331–337Google Scholar
  14. Ebadi A, Soltan Mohammadzadeh JS, Khudiev A (2009) What is the correct form of BET isotherm for modeling liquid phase adsorption? Adsorption 15:65–73.  https://doi.org/10.1007/s10450-009-9151-3 CrossRefGoogle Scholar
  15. Ediz N, Bentli I, Tatar I (2010) Improvement in filtration characteristics of diatomite by calcination. Int J Miner Process 94:129–134.  https://doi.org/10.1016/j.minpro.2010.02.004 CrossRefGoogle Scholar
  16. El Haddad M, Mamouni R, Saffaj N, Lazar S (2012) Removal of a cationic dye—Basic Red 12—from aqueous solution by adsorption onto animal bone meal. J Assoc Arab Univ Basic Appl Sci 12:48–54.  https://doi.org/10.1016/j.jaubas.2012.04.003 Google Scholar
  17. Foo KY, Hameed BH (2010) Insights into the modeling of adsorption isotherm systems. Chem Eng J 156:2–10.  https://doi.org/10.1016/j.cej.2009.09.013 CrossRefGoogle Scholar
  18. Freundlich HMF (1906) Over the adsorption in solution. J Phys Chem 57:385–471Google Scholar
  19. Gregg SJ, Sing KSW (1982) Adsorption, surface area and porosity, 2nd edn. Academic Press, LondonGoogle Scholar
  20. Ho YS, McKay G (1999) Pseudo-second order model for sorption processes. Process Biochem 34:451–465.  https://doi.org/10.1016/S0032-9592(98)00112-5 CrossRefGoogle Scholar
  21. Ibrahim SS, Selim AQ (2012) Heat treatment of natural diatomite. Physicochem Probl Miner Process 48:413–424.  https://doi.org/10.5277/ppmp120208 Google Scholar
  22. Iddou A, Ouali MS (2008) Waste-activated sludge (WAS) as Cr(III) sorbent biosolid from wastewater effluent. Colloids Surf B Biointerfaces 66:240–245.  https://doi.org/10.1016/j.colsurfb.2008.06.018 CrossRefGoogle Scholar
  23. Iddou A, Hadj Youcef M, Aziz A, Ouali MS (2011) Biosorptive removal of lead (II) ions from aqueous solutions using Cystoseira stricta biomass: study of the surface modification effect. J Saudi Chem Soc 15:83–88.  https://doi.org/10.1016/j.jscs.2010.10.007 CrossRefGoogle Scholar
  24. Johari K, Saman N, Song ST et al (2016) Adsorption enhancement of elemental mercury by various surface modified coconut husk as eco-friendly low-cost adsorbents. Int Biodeterior Biodegrad 109:45–52.  https://doi.org/10.1016/j.ibiod.2016.01.004 CrossRefGoogle Scholar
  25. Kelewou H, Merzouki M, Lhassani A (2014) Biosorption of textile dyes Basic Yellow 2 (BY2) and Basic Green 4 (BG4) by the live yeast Saccharomyces cerevisiae. J Mater Environ Sci 5:633–640Google Scholar
  26. Lagergren S (1898) Zur theorie der sogenannten adsorption geloster stoffe. K. Sven. Vetenskapsakademiens. Handl 24:1–39Google Scholar
  27. Langmuir I (1917) The Constitution and Fundamental Properties of Solids and Liquids. J Am Chem Soc 39:1848–1906.  https://doi.org/10.1021/ja02254a006 CrossRefGoogle Scholar
  28. Mahmoodi NM, Arami M (2008) Modeling and sensitivity analysis of dyes adsorption onto natural adsorbent from colored textile wastewater. J Appl Polym Sci 109:4044–4048.  https://doi.org/10.1002/app CrossRefGoogle Scholar
  29. Mahmoodi NM, Hayati B, Arami M, Lan C (2011) Adsorption of textile dyes on Pine Cone from colored wastewater: kinetic, equilibrium and thermodynamic studies. Desalination 268:117–125.  https://doi.org/10.1016/j.desal.2010.10.007 CrossRefGoogle Scholar
  30. Mittal A, Mittal J, Malviya A, Gupta VK (2009) Adsorptive removal of hazardous anionic dye “Congo red” from wastewater using waste materials and recovery by desorption. J Colloid Interface Sci 340:16–26.  https://doi.org/10.1016/j.jcis.2009.08.019 CrossRefGoogle Scholar
  31. Naderi M (2014) Surface area: Brunauer–Emmett–Teller (BET). Prog Filtr.  https://doi.org/10.1016/b978-0-12-384746-1.00014-8 Google Scholar
  32. Ncibi MC, Mahjoub B, Ben Hamissa AM et al (2009) Biosorption of textile metal-complexed dye from aqueous medium using Posidonia oceanica (L.) leaf sheaths: mathematical modelling. Desalination 243:109–121.  https://doi.org/10.1016/j.desal.2008.04.018 CrossRefGoogle Scholar
  33. Rangsriwatananon K, Chaisena A, Thongkasam C (2008) Thermal and acid treatment on natural raw diatomite influencing in synthesis of sodium zeolites. J Porous Mater 15:499–505.  https://doi.org/10.1007/s10934-007-9098-2 CrossRefGoogle Scholar
  34. Reddad Z, Gerente C, Andres Y, Pierre LC (2002) Adsorption of several metal ions onto a low-cost biosorbent: kinetic and equilibrium studies. Environ Sci Technol 36:2067–2073CrossRefGoogle Scholar
  35. Sheshdeh RK, Nikou MRK, Badii K et al (2014) Equilibrium and kinetics studies for the adsorption of Basic Red 46 on nickel oxide nanoparticles-modified diatomite in aqueous solutions. J Taiwan Inst Chem Eng 45:1792–1802.  https://doi.org/10.1016/j.jtice.2014.02.020 CrossRefGoogle Scholar
  36. Sing K, Williams R (2004) Physisorption hysteresis loops and the characterization of nanoporous materials. Adsorpt Sci Technol 22:773–782.  https://doi.org/10.1260/0263617053499032 CrossRefGoogle Scholar
  37. Sun Z, Zhang Y, Zheng S et al (2013) Preparation and thermal energy storage properties of paraffin/calcined diatomite composites as form-stable phase change materials. Thermochim Acta 558:16–21.  https://doi.org/10.1016/j.tca.2013.02.005 CrossRefGoogle Scholar
  38. Vimonses V, Lei S, Jin B et al (2009a) Kinetic study and equilibrium isotherm analysis of Congo Red adsorption by clay materials. Chem Eng J 148:354–364.  https://doi.org/10.1016/j.cej.2008.09.009 CrossRefGoogle Scholar
  39. Vimonses V, Lei S, Jin B et al (2009b) Adsorption of congo red by three Australian kaolins. Appl Clay Sci 43:465–472.  https://doi.org/10.1016/j.clay.2008.11.008 CrossRefGoogle Scholar
  40. Wang S, Zhu ZH (2006) Characterisation and environmental application of an Australian natural zeolite for basic dye removal from aqueous solution. J Hazard Mater 136:946–952.  https://doi.org/10.1016/j.jhazmat.2006.01.038 CrossRefGoogle Scholar
  41. Wang Y, Mu Y, Zhao QB, Yu HQ (2006) Isotherms, kinetics and thermodynamics of dye biosorption by anaerobic sludge. Sep Purif Technol 50:1–7.  https://doi.org/10.1016/j.seppur.2005.10.012 CrossRefGoogle Scholar
  42. Wang B, de Godoi FC, Sun Z et al (2015) Synthesis, characterization and activity of an immobilized photocatalyst: natural porous diatomite supported titania nanoparticles. J Colloid Interface Sci 438:204–211.  https://doi.org/10.1016/j.jcis.2014.09.064 CrossRefGoogle Scholar
  43. Weber WJ, Morris JC (1963) Kinetics of Adsorption on Carbon from Solution. J Sanit Eng Div 89:31–60Google Scholar
  44. Ye X, Kang S, Wang H et al (2015) Modified natural diatomite and its enhanced immobilization of lead, copper and cadmium in simulated contaminated soils. J Hazard Mater 289:210–218.  https://doi.org/10.1016/j.jhazmat.2015.02.052 CrossRefGoogle Scholar
  45. Yuan P, Liu D, Fan M et al (2010) Removal of hexavalent chromium [Cr(VI)] from aqueous solutions by the diatomite-supported/unsupported magnetite nanoparticles. J Hazard Mater 173:614–621.  https://doi.org/10.1016/j.jhazmat.2009.08.129 CrossRefGoogle Scholar

Copyright information

© Islamic Azad University (IAU) 2018

Authors and Affiliations

  • H. Aguedal
    • 1
  • A. Iddou
    • 1
  • A. Aziz
    • 1
  • A. Shishkin
    • 2
  • J. Ločs
    • 2
  • T. Juhna
    • 3
  1. 1.Laboratoire de Valorisation des Matériaux, Département de Génie des Procédés, Faculté des Sciences et de la TechnologieUniversité Abdelhamid Ibn Badis – MostaganemMostaganemAlgeria
  2. 2.Rudolfs Cimdins Riga Biomaterials Innovations and Development Centre of RTU, Institute of General Chemical Engineering, Faculty of Materials Science and Applied ChemistryRiga Technical UniversityRigaLatvia
  3. 3.Laboratory of Water Research, Faculty of Civil EngineeringRiga Technical UniversityRigaLatvia

Personalised recommendations