Advertisement

Residual Strength of Steel Structures After Fire Events Considering Material Damages

  • Zhanzhan TangEmail author
  • Tao Wei
  • Yao Ma
  • Lingkun Chen
Research Article - Civil Engineering
  • 28 Downloads

Abstract

It is an essential task for engineers to evaluate the residual strength of a fire-damaged steel structure, especially when collapse does not occur during the fire event. First of all, the mechanical properties of structural steels after fire were investigated through the experimental data. The stress–strain relationship model considering fire events was established. Then, the remaining load bearing capacity of a simple steel frame was evaluated using both the fiber and shell element numerical models. Finally, case study about the post-fire residual strength of a complex steel truss bridge was carried out. The results show that mechanical properties of the structural steels decrease after cooling down from an elevated temperature higher than \(500\, {^{\circ }}\hbox {C}\). Compared with the shell element model, the fiber element model is not able to predict accurately the post-fire inelastic behavior of a thin-walled steel structure. In most cases, the fire-exposed steel bridge still retains its original strength. However, it is apparently affected by the positions where the fire breaks out. The worst-case scenario is that the fire event occurs at the joint near the bearing supports, in which the strength decreases dramatically.

Keywords

Steel structure Residual strength Structural steel Fire event Post-fire 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgements

The research work described in this paper was financially supported by the grants from the National Natural Science Foundation of China (No. 51708485), the Jiangsu Planned Projects for Postdoctoral Research Funds (No. 1701191B) and the China Postdoctoral Science Foundation (No. 2017M611925), and their support is gratefully acknowledged by the authors. Also, the authors would like to express their gratitude to Ms. Suwen Zhou for her diligent assistance in the material experiments.

References

  1. 1.
    Kodur, V.; Gu, L.; Garlock, ME.: Review and assessment of fire event in bridges. J. Transp. Res. Board. 2172. Washington D.C. (2010)Google Scholar
  2. 2.
    Jeoung, C.; Kim, W.; Gil, H.: Bridge fire risk assessment on the highway in South Korea. Adv. Mater. Res. 1025–1026, 854–857 (2014)CrossRefGoogle Scholar
  3. 3.
    Ding, F.; Yu, Z.; Wen, L.: Experimental research on mechanical properties of Q235 steel after high temperature treatment. J. Build. Mater. 9(2), 245–249 (2006). (In Chinese)Google Scholar
  4. 4.
    Cao, P.Z.; Chen, J.F.; Zhao, W.: Experimental investigation on tensile strength of butt welded joint post high temperatures. China Weld. 18(3), 21–26 (2009)Google Scholar
  5. 5.
    Wang, W.Y.; Liu, T.Z.; Liu, J.P.: Experimental study on post-fire mechanical properties of high strength Q460 steel. J. Constr. Steel Res. 114, 100–109 (2015)CrossRefGoogle Scholar
  6. 6.
    Li, G.Q.; Lyu, H.; Zhang, C.: Post-fire mechanical properties of high strength Q690 structural steel. J. Constr. Steel Res. 132, 108–116 (2017)CrossRefGoogle Scholar
  7. 7.
    Kang, L.; Suzuki, M.; Ge, H.B.; Wu, B.: Experiment of ductile fracture performances of HSSS Q690 after a fire. J. Constr. Steel Res. 146, 109–121 (2018)CrossRefGoogle Scholar
  8. 8.
    Azhari, F.; Heidarpour, A.; Zhao, X.L.; Hutchinson, C.R.: Post-fire mechanical response of ultra-high strength (grade 1200) steel under high temperatures: linking thermal stability and microstructure. Thin-Walled Struct. 119, 114–125 (2017)CrossRefGoogle Scholar
  9. 9.
    Qiang, X.H.; Bijlaard, F.S.K.; Kolstein, H.: Post-fire mechanical properties of high strength structural steels S460 and S690. Eng. Struct. 35, 1–10 (2012)CrossRefGoogle Scholar
  10. 10.
    Qiang, X.H.; Bijlaard, F.S.K.; Kolstein, H.: Post-fire performance of very high strength steel S960. Steel Constr. 80(1), 235–242 (2013)CrossRefGoogle Scholar
  11. 11.
    Aziz, E.M.; Kodur, V.K.: Effect of temperature and cooling regime on mechanical properties of high-strength low-alloy steel. Fire Mater. 40(7), 926–939 (2016)CrossRefGoogle Scholar
  12. 12.
    Lee, J.; Engelhardt, M.D.; Taleff, E.M.: Mechanical properties of ASTM A992 steel after fire. Eng. J. 49(1), 33–44 (2012)Google Scholar
  13. 13.
    China Association for Engineering Construction Standardization. Technical code for fire safety of steel structure in buildings. CECS 200: 2006, Beijing (2006)Google Scholar
  14. 14.
    China Association for Engineering Construction Standardization. Standard for building structural assessment after fire. CECS 252: 2009, Beijing (2009)Google Scholar
  15. 15.
    British Standards Institution. Structural use of steelwork in building-part 8: code of practice for fire resistant design. BS 5950-8, London (1998)Google Scholar
  16. 16.
    Iu, C.K.; Chan, S.L.; Zha, X.X.: Nonlinear pre-fire and post-fire analysis of steel frames. Eng. Struct. 27(11), 1689–1702 (2005)CrossRefGoogle Scholar
  17. 17.
    Falke, J.; Mustafa, HN.: Load bearing capacity of steel structures after fire. In: Structures in Fire-Proceedings of the Sixth International Conference, SiF’ 10 (2010)Google Scholar
  18. 18.
    Ariyanayagam, A.; Mahendran, M.: Residual capacity of fire exposed light gauge steel frame walls. Thin-Walled Struct. 124, 107–120 (2018)CrossRefGoogle Scholar
  19. 19.
    Maraveas, C.; Fasoulakis, Z.; Tsavdaridis, K.D.: Post-fire assessment and reinstatement of steel structures. J. Struct. Fire Eng. 8(2), 181–201 (2017)CrossRefGoogle Scholar
  20. 20.
    Kmet, S.; Tomko, M.; Demjan, I.; Pesek, L.; Priganc, S.: Analysis of a damaged industrial hall subjected to the effects of fire. Struct. Eng. Mech. 58(5), 757–781 (2016)CrossRefGoogle Scholar
  21. 21.
    Standardization Administration of the People’s Republic of China. Metallic materials—tensile testing—Part 1: method of test at room temperature. GB/T 228, 1-2010, Beijing (2010)Google Scholar
  22. 22.
    Tao, Z.; Wang, X.Q.; Uy, B.: Stress–strain curves of structural and reinforcing steels after exposure to elevated temperatures. J. Mater. Civil Eng. 25(9), 1306–1316 (2013)CrossRefGoogle Scholar
  23. 23.
    Wang, X.Q.; Tao, Z.; Song, T.Y.; Han, L.H.: Stress–strain model of austenitic stainless steel after exposure to elevated temperatures. J. Constr. Steel Res. 99(8), 129–139 (2014)CrossRefGoogle Scholar
  24. 24.
    Yu, Z.W.; Ding, F.X.; Wen, H.L.: Experimental research on the mechanical properties of steel after high temperature. Fourth Int. Conf. Adv. Steel Struct. 2, 1071–1076 (2005)Google Scholar
  25. 25.
    Zhang, Y.J.; Zhu, Y.; Zhao, S.; Hu, K.X.: Experimental research on mechanical properties of steel cooled in different modes after high temperature treatment. Struct. Eng. 25(5), 104–109 (2009). (In Chinese)Google Scholar
  26. 26.
    Chen, Z.P.; Chen, J.R.; Xue, J.Y.; Chen, Y.L.: Experimental study of mechanical behavior of steel and recycled aggregate concrete after high temperature. Ind. Constr. 44(11), 1–4 (2014). (In Chinese)Google Scholar
  27. 27.
    Chiew, S.P.; Zhao, M.S.; Lee, C.K.: Mechanical properties of heat-treated high strength steel under fire/post-fire conditions. J. Constr. Steel Res. 98(9), 12–19 (2014)CrossRefGoogle Scholar
  28. 28.
    Gunalan, S.; Mahendran, M.: Experimental investigation of post-fire mechanical properties of cold-formed steels. Thin-Walled Struct. 84, 241–254 (2014)CrossRefGoogle Scholar
  29. 29.
    Chen, Z.H.; Lu, J.; Liu, H.B.; Liao, X.W.: Experimental study on the post-fire mechanical properties of high-strength steel tie rods. J. Constr. Steel Res. 121, 311–329 (2016)CrossRefGoogle Scholar
  30. 30.
    Zheng, Y.; Usami, T.; Ge, H.B.: Ductility of thin-walled steel box stub-columns. J. Struct. Eng. 126(11), 1304–1311 (2000)CrossRefGoogle Scholar

Copyright information

© King Fahd University of Petroleum & Minerals 2019

Authors and Affiliations

  1. 1.College of Civil Science and EngineeringYangzhou UniversityYangzhouChina

Personalised recommendations