Piecewise Linear Weighted Iterative Algorithm for Beam Alignment in Scanning Beam Interference Lithography
- 14 Downloads
To obtain a good interference fringe contrast and high fidelity, an automated beam iterative alignment is achieved in scanning beam interference lithography (SBIL). To solve the problem of alignment failure caused by a large beam angle (or position) overshoot exceeding the detector range while also speeding up the convergence, a weighted iterative algorithm using a weight parameter that is changed linearly piecewise is proposed. The changes in the beam angle and position deviation during the alignment process based on different iterative algorithms are compared by experiment and simulation. The results show that the proposed iterative algorithm can be used to suppress the beam angle (or position) overshoot, avoiding alignment failure caused by over-ranging. In addition, the convergence speed can be effectively increased. The algorithm proposed can optimize the beam alignment process in SBIL.
KeywordsPiecewise linear weighted iterative algorithm beam alignment scanning beam interference lithography (SBIL) overshoot suppression convergence speed
- K. C. Tseng, S. T. Hong, T. H. Lin, T. H. Chuang, and C. C. Fu, “WGP structures patterned by Lloyd′s mirror laser interference lithography system integrate into MEMS physical sensor device,” SPIE, 2016, 9759: 97591E-1–97591E-6.Google Scholar
- K. Lee, J. Lee, B. A. Mazor, and S. R. Forrest, “Transforming the cost of solar-to-electrical energy conversion: integrating thin-film GaAs solar cells with non-tracking mini-concentrators,” Light: Science & Applications, 2015, 4: e288-1–e288-7.Google Scholar
- M. Gu, X. P. Li, and Y. Y. Gao, “Optical storage arrays: a perspective for future big data storage,” Light: Science & Applications, 2014, 3: e177-1–e177-11.Google Scholar
- Q. S. Li, L. Cai, Y. H. Ma, J. H. Yang, Y. Yang, Q. J. Meng, et al., “Research progress of biosensors based on long period fiber grating,” Chinese Optics, 2018, 11(3): 476–502.Google Scholar
- K. L. Jim, C. W. Leung, and H. L. W. Chan, “Photonic crystal cavity embedded barium strontium titanate thin-film rib waveguide prepared by focused ion beam etching,” Thin solid films, 2010, 518(24): e101–e103.Google Scholar
- D. X. Liu, H. Xia, Y. L. Sun, Q. D. Chen, and W. F. Dong, “Femtosecond laser direct writing bio-gel template for in situ synthesis of nanoparticles,” Chinese Optics, 2014, 7(4): 608–615.Google Scholar
- J. Montoya, “Toward nano-accuracy in scanning beam interference lithography,” Ph.D. dissertation, Massachusetts Institute of Technology, Boston, USA, 2006.Google Scholar
- W. Wei, “Study on beam quality control of the scanning beam interference lithography system,” Ph.D. dissertation, University of Chinese Academy of Sciences, Beijing, China, 2017.Google Scholar
- C. G. Chen, “Beam alignment and image metrology for scanning beam interference lithography: fabricating gratings with nanometer phase accuracy,” Ph.D. dissertation, Massachusetts Institute of Technology, USA, 2003.Google Scholar
- W. Wang, Bayanheshig, Y. Song, S. Jiang, and M. Z. Pan, “Beam alignment and convergence analysis of scanning beam interference lithography system,” Chinese Journal of Lasers, 2016, 43(12): 176–183.Google Scholar
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.