# Satellite clock stability analysis depending on the reference clock type

- 106 Downloads

## Abstract

Knowledge of the GNSS satellite clock error is essential for real-time PPP and other high-rate applications in GNSS positioning. This work presents the characterisation of short-term stability of the atomic GNSS clocks depending on the type of reference clock. Calculations are performed by usage of high-rate 1 s GPS observations on the IGS stations located in Europe. The clock parameters are estimated epoch by epoch using back-substitution steps. Furthermore, there is a clock stability analysis of stations selected as reference clocks in a 2-week period. The analysis presents a characterisation of the GPS satellite clocks as the Allan deviation covering averaging intervals from 2^{0} to 2^{10} s.

## Keywords

Allan deviation Clock stability GPS GNSS High-rate data## Introduction

The principle of GNSS (Global Navigation Satellite Systems) positioning based on one-way measurements—satellite signals are registered by receivers. Equation system of four unknowns (three coordinates and one receiver clock error) required the view of at least four satellites every epoch, especially in kinematic positioning. This method is called absolute positioning using a single receiver with pseudoranges, and there is no need of timescales synchronisation. For more precise purposes, phase measurements with the usage of two or more receivers are in use. In that kind of measurements, determination of the GNSS satellite on-board clock corrections is the most important part. Satellite clock corrections are provided via navigation message in real-time or in post-processing (Krawinkel and Schön 2016). Satellite clock correction determination needs continuous observations based on large number of permanent stations (Gong et al. 2013). The biggest network of permanent station is IGS (The International GNSS Service). IGS provides precise GNSS products such as precise ephemeris or stations’ coordinates since 1994 (Beutler et al. 2009). Five-minute sampling clock corrections are available at IGS for many years; 30-s sampling data are available since GPS week 1406 (December 17, 2006) (Gendt 2007) by a four IGS ACs (analysis centres) (Bock et al. 2009). In 2012, the Multi-GNSS EXperiment (MGEX) was initiated (Montenbruck et al. 2013) to prepare the services for new GNSS systems, such as BeiDou or Galileo (Prange et al. 2017a). Since GPS week 1961 (August 6, 2017), MGEX 30-s clock corrections are also available. Products with this interval are provided by three IGS ACs: CODE (Centre for Orbit Determination in Europe) (Prange et al. 2017b), GFZ (Geo Forschungs Zentrum) (Uhlemann et al. 2015) and CNES/CLS (Centre National d’Etudes Spatiales/Collecte Localisation par Satellite) (Loyer et al. 2016). As research shows, clock products provided by different institutions and analysis centres differ insignificantly from each other, but generally, accuracy is at the same level (Ruan et al. 2017). High-rate clock products (< 5 s) are used in 1-Hz and lower measurement intervals, mostly in absolute measurements, e.g. PPP. In this positioning method, the satellite clock error cannot be deleted by differencing observations, and the knowledge of high-quality clock corrections is extremely important (Kouba and Héroux 2001; Lou et al. 2016; Soycan 2011). High-rate PPP measurements are in use in the monitoring of natural and anthropological phenomena such as seismic wave motions (Xu et al. 2013), permanent stations monitoring (Maciuk 2016a; Szombara and Maciuk 2017), landslides control surveys (Şanlıoğlu et al. 2016) and earthquakes observations (Kaloop and Rabah 2016).

## Clock stability analysis theory

Frequency accuracy refers to consistency from the measured frequency (or calculated rate) and the nominal one and can be defined as:

*σ*is the frequency accuracy,

*f*

_{0}is the nominal frequency and

*f*

_{x}is the actual frequency value. Measurement frequency accuracy analysis needs a longer frequency measurement time as far as possible. If frequency measurement time is too short, short-term stability of frequency standard is relatively poor, and random frequency fluctuations will affect the accuracy of measurement error.

Frequency accuracy is calculated by the time difference method, thus can be called the relative frequency deviation as the accuracy of the satellite atomic clock. The atomic clock frequency can be described by the frequency drift rate. The least-squares solution of the frequency drift rate is described as (Zheng et al. 2017):

*D*is the frequency drift rate, \( \overline{y} \) is the mean value of relative frequency value

*y*

_{i},

*t*

_{i}is the time measure of the relative frequency value and

*N*is the number of samples; the formulas of \( \overline{y} \) and \( \overline{t} \) are:

The Allan deviation or its square (Allan variance) is the most often used method for satellite clock estimation (Allan 1983). If discrete set of time deviations *x*_{i} as a sequence for the measurable time difference and given nominal spacing between adjacent time difference measurements is *τ*_{0}, then the average fractional frequency for the *i*th measurement interval is (Allan 1987):

*τ*

_{0}over

*y*

_{i}denotes the average over an interval

*τ*

_{0}. According to that, the Allan variance generally can be described as a half of the mean square value of the change in frequency error (Petovello and Lachapelle 2000):

*τ*. If

*τ*

_{0}is the minimum sampling of original data set \( {\overline{y}}_i^{\tau_0} \), then the change of the sampling time to

*τ*=

*nτ*

_{0}by averaging

*n*adjacent values of \( {\overline{y}}_i^{-{\tau}_0} \) to get a new fractional frequency estimate \( {\overline{y}}_i^{\tau } \), with sampling time

*τ*as input to (6). For a finite set of

*M*, values of \( {\overline{y}}_i^{\tau_0} \) for general

*τ*becomes (Allan 1987):

*τ*=

*nτ*

_{0}, and (Allan 1987).

Or, alternatively, (7) may be written as (9):

*M*=

*N*− 1 is the number of frequency samples, and

*N*is the number of time samples,

*i*= 1 to

*M*+ 1:

From Equations (9) and (11), we see that \( {\sigma}_y^2\left(\tau \right) \) acts like a second-difference operator, which makes use of overlapping estimate of the expected values of frequency measurements (Allan et al. 1988). The Allan deviation (denoted as *σ*_{y}(*τ*) or ADEV) versus time interval is usually plotted in a log-log format. It is also known as a two-sample variance and describes clock behaviour as a function of the time between samples of *τ* size.

## GNSS observation models

Precise clock products are extremely important in GNSS positioning. It is extremely important firstly in absolute positioning method called PPP (Precise Point Positioning) demanding high-quality products (Alcay et al. 2012a; Maciuk 2018a). Secondly, in real-time positioning methods (Krzyżek 2015), available ultra-rapid orbit might improve results contrary to the broadcasted orbit (Maciuk 2016b). And finally, clock files are required among other precise clock products in measurements in difficult conditions such as under difficult sky-view conditions (Maciuk 2018b; Alcay et al. 2012b).

Precise clock product accuracy depends on the provider, which leads to slight differences; clock products can diverge by accuracy, availability, update rate and sampling rate (Zheng et al. 2017). The pseudorange (code) and phase observations in GNSS positioning are smudged by various factors. It can be classified into receiver and satellite clock bias, satellite position error, ionosphere and troposphere delays, earth rotation corrections, relativistic and multipath effects and others. Therefore, the above factors have to be eliminated to determine satellite clock bias. Carrier phase observations are much more precise than pseudorange observations; both observations can be expressed as (Bock et al. 2009; Li et al. 2016):

*δ*

^{j}and

*δ*

_{k}are satellite and receiver clock corrections, respectively; \( {\rho}_{fk, iono}^j \) and \( {\rho}_{k, trop}^j \) are ionospheric and tropospheric refractions, respectively;

*b*

^{j}is the differential clock bias (DCB);

*c*is the speed of light; \( {\varphi}_{fk}^j \) is the observed phase;

*λ*

_{f}is the wavelength of frequency

*f*and \( {N}_k^j \) is the ambiguity. Comparing code and phase observations, we have the ambiguity term and the opposite sign for ionosphere refraction. The ambiguity term (\( {\lambda}_f\bullet {N}_k^j \)) is eliminated by differences of phase measurements referring to subsequent epochs as:

Precise GNSS orbits, ERPs (Earth Rotation Parameters), station coordinates, DCBs and troposphere parameters are used as known; ionosphere impact is eliminated in ionosphere-free LC (linear combination) (Han et al. 2001), so Equations (11) and (12) are expressed as Equations (14) and (15), respectively:

For the phase-difference processing, the differences between epoch-wise estimated code and receiver corrections are used as a priori values. Differences between subsequent observations epochs are correlated as long as they are connected with at least one ambiguity term (Bock et al. 2009). Clock corrections might be estimated from zero-difference data in two different ways (Dach and Walser 2013). Firstly, by estimating together with other parameters (e.g. coordinate and troposphere) in main normal equations; this method is widely known. The second was as set-up pre-eliminated epoch by epoch. After solving normal equations, resulting parameters are introduced as fixed when epoch parameters are estimated epoch by epoch. In other words, a single solution is set up as a reference for a number of epochs for defined interval (usually 30 s or 300 s). This value might be obtained either from the code measurements or from the external high-accuracy input of clock correction file. This procedure is done separately for each individual satellite and receiver clock. For a particular clock, such combinations could be written as (Zhang et al. 2011):

*n*is number of epochs, with constrains

For example, if 5-min sampling clock data are in use as input and epoch-differencing is done for 30-s sampling data, the known clock corrections *δ*_{fix}(*t*_{i}) are introduced with 5-min resolution. In both cases, estimated clock corrections are identical (Dach and Walser 2013). The second approach dramatically reduces the number of parameters in the main normal equations, so it is computationally and efficiently productive compared to the first method.

## Experiment description and results

Basic information of the tracking stations involved in the experiment

Station | Country | City | Latitude | Longitude | Clock |
---|---|---|---|---|---|

DLF1 | Netherlands | Delft | 51.99 | 4.39 | External caesium |

GOP6 | Czech Republic | Ondrejov | 49.91 | 14.79 | External caesium |

GOP7 | Czech Republic | Ondrejov | 49.91 | 14.79 | External caesium |

JOZ2 | Poland | Jozefoslaw | 52.10 | 21.03 | Internal |

KIR8 | Sweden | Kiruna | 67.88 | 21.06 | External rubidium |

M0SE | Italy | Roma | 41.89 | 12.49 | External rubidium |

MATE | Italy | Matera | 40.65 | 16.70 | External h-maser |

NICO | Cyprus | Nicosia | 35.14 | 33.40 | Internal |

ONS1 | Sweden | Onsala | 57.40 | 11.92 | External h-maser |

PDEL | Portugal | Ponta Delgada | 37.75 | − 25.66 | External quartz |

REYK | Iceland | Reykjavik | 64.14 | − 21.96 | Internal |

WTZR | Germany | Bad Koetzting | 49.14 | 12.88 | External h-maser Efos 18 |

YEBE | Spain | Yebes | 40.52 | − 3.09 | External h-maser |

ZIM2 | Switzerland | Zimmerwald | 46.88 | 7.47 | Internal |

The analysis includes only the reference stations located in Europe belonging to the IGS network and providing 1-Hz observations (Fig. 1). As a reference clock (fixed), three stations were taken with different types of clock: internal (ZIM2), external caesium (GOP6) and external h-maser (WTZR), located in the centre of network. Satellite clocks were calculated with respect to a specific receiver clock. The selection of reference stations was taken both on the clock type and on the localisation in the analysed network.

*τ*= 30 s), discrepancies are evident: 1.9e-11 s for ZIM2 station, 5.9e-12 s for GOP6 and 1.2e-12 s for WTZR. Moving to longer averaging intervals,

*τ*variations between analysed clocks are getting smaller. For each analysed value, the h-maser clock is the most stable, and the internal clock is the least, except the longest analysed

*τ*= 15,360 s. In addition, the h-maser clock characterises by one order of magnitude with better stability than the internal one and by half of one order of magnitude against the caesium one.

Information about satellites (http://www2.unb.ca/gge/Resources/GPSConstellationStatus.txt, https://www.navcen.uscg.gov/?Do=constellationstatus)

PRN | SVN | Orbit plane | Block | Frequency standard | Launch date | Available (UT) |
---|---|---|---|---|---|---|

G20 | 51 | E4 | IIR-4 | Rb1 | 2000-05-11 | 2000-06-01 16:09 |

G18 | 34 | D6 | IIR-7 | Rb1 | 2001-01-30 | 2001-02-15 15:51 |

G16 | 56 | B1 | IIR-8 | Rb3 | 2003-01-29 | 2003-02-18 15:53 |

G21 | 45 | D3 | IIR-9 | Rb3 | 2003-03-31 | 2003-04-12 05:27 |

G31 | 52 | A2 | IIR-M-2 | Rb3 | 2006-09-25 | 2006-10-12 22:53 |

G29 | 57 | C1 | IIR-M-5 | Rb3 | 2007-12-20 | 2008-01-02 20:41 |

G05 | 50 | E3 | IIR-M-8 | Rb1 | 2009-08-17 | 2009-08-27 14:40 |

G27 | 66 | C2 | IIF-4 | Rb2 | 2013-05-15 | 2013-06-21 19:58 |

G26 | 71 | B5 | IIF-9 | Rb1 | 2015-03-25 | 2015-04-20 22:22 |

G10 | 73 | E2 | IIF-11 | Rb1 | 2015-07-15 | 2015-08-12 16:53 |

Figure 3 (Appendix) presents ADEV for each of the three different reference clock solutions of all satellites that fulfil the condition described in the previous paragraph. Selected values are presented in Table 2. As expected, all three reference clock solutions show a different behaviour. For a ZIM2 station (internal clock), satellite clock stability varies between 2.96E-11 s (for *τ* = 1 s) and 1.16E-12 s (*τ* = 1024 s). In case of a GOP6 (caesium clock), clock stability varies between 2.09E-11 s (*τ* = 1 s) and 1.51E-13 s (*τ* = 1024 s). The most stable was WTZR clock (h-maser clock) with stability from 1.97E-11 s (*τ* = 1 s) to 5.87E-14 s (*τ* = 1024 s)

*τ*= 1 s, the least stable is G16 satellite clock with instability at 2-3E-11 s level. The ADEV curves for ZIM2 and GOP6 stations are very similar; there are no deviations between each satellite instead of the event explained at the beginning of the paragraph. In the case of the most stable resolution based on WTZR reference clock, G26 and G27 satellite clocks have a clearly visible better ADEV results for

*τ*> 8 s values (Table 3). There is no connection between these pairs of satellites based on the values placed in Table 1—different planes, block and frequency standard.

Allan deviation of selected intervals

Reference station | PRN | Averaging intervals of Allan deviation [s] | |||||
---|---|---|---|---|---|---|---|

1 | 4 | 16 | 64 | 256 | 1024 | ||

ZIM2 | G05 | 2.03E-11 | 8.70E-12 | 4.34E-12 | 3.01E-12 | 1.84E-12 | 1.81E-12 |

G10 | 1.96E-11 | 8.36E-12 | 4.23E-12 | 2.77E-12 | 1.90E-12 | 1.55E-12 | |

G16 | 2.96E-11 | 1.31E-11 | 6.15E-12 | 3.86E-12 | 2.53E-12 | 2.03E-12 | |

G18 | 2.01E-11 | 8.47E-12 | 4.30E-12 | 3.84E-12 | 2.04E-12 | 1.47E-12 | |

G20 | 1.96E-11 | 8.23E-12 | 4.23E-12 | 2.71E-12 | 1.73E-12 | 1.34E-12 | |

G21 | 2.15E-11 | 9.02E-12 | 6.04E-12 | 5.05E-12 | 2.55E-12 | 1.51E-12 | |

G26 | 2.51E-11 | 9.42E-12 | 3.58E-12 | 2.04E-12 | 1.78E-12 | 1.62E-12 | |

G27 | 1.96E-11 | 8.32E-12 | 3.50E-12 | 2.03E-12 | 1.74E-12 | 1.56E-12 | |

G29 | 2.04E-11 | 8.42E-12 | 3.96E-12 | 2.95E-12 | 1.79E-12 | 1.64E-12 | |

G31 | 1.97E-11 | 8.52E-12 | 4.35E-12 | 2.27E-12 | 1.26E-12 | 1.75E-12 | |

GOP6 | G05 | 1.16E-11 | 6.49E-12 | 3.73E-12 | 2.79E-12 | 1.42E-12 | 4.39E-13 |

G10 | 9.96E-12 | 5.76E-12 | 3.65E-12 | 2.57E-12 | 7.71E-13 | 3.11E-13 | |

G16 | 2.09E-11 | 1.05E-11 | 5.11E-12 | 2.30E-12 | 1.16E-12 | 1.51E-13 | |

G18 | 1.11E-11 | 6.02E-12 | 4.32E-12 | 3.80E-12 | 1.31E-12 | 2.51E-13 | |

G20 | 1.01E-11 | 5.88E-12 | 3.81E-12 | 2.47E-12 | 1.14E-12 | 3.63E-13 | |

G21 | 1.24E-11 | 6.53E-12 | 5.02E-12 | 4.32E-12 | 1.44E-12 | 2.22E-13 | |

G26 | 1.82E-11 | 7.10E-12 | 2.92E-12 | 1.35E-12 | 6.41E-13 | 1.76E-13 | |

G27 | 1.01E-11 | 5.92E-12 | 2.91E-12 | 1.33E-12 | 5.96E-13 | 1.75E-13 | |

G29 | 1.18E-11 | 6.09E-12 | 3.86E-12 | 2.66E-12 | 9.10E-13 | 2.25E-13 | |

G31 | 1.16E-11 | 6.22E-12 | 3.83E-12 | 2.20E-12 | 1.00E-12 | 3.04E-13 | |

WTZR | G05 | 9.36E-12 | 3.65E-12 | 2.68E-12 | 2.36E-12 | 1.08E-12 | 3.69E-13 |

G10 | 7.33E-12 | 2.93E-12 | 2.43E-12 | 2.00E-12 | 6.09E-13 | 1.90E-13 | |

G16 | 1.97E-11 | 8.86E-12 | 4.09E-12 | 2.17E-12 | 7.68E-13 | 4.26E-13 | |

G18 | 8.74E-12 | 3.49E-12 | 3.11E-12 | 3.39E-12 | 1.04E-12 | 1.87E-13 | |

G20 | 7.48E-12 | 2.99E-12 | 2.58E-12 | 2.08E-12 | 8.82E-13 | 2.97E-13 | |

G21 | 1.05E-11 | 4.24E-12 | 4.19E-12 | 3.86E-12 | 1.14E-12 | 1.95E-13 | |

G26 | 1.72E-11 | 5.15E-12 | 9.42E-13 | 3.50E-13 | 1.39E-13 | 8.57E-14 | |

G27 | 7.65E-12 | 3.17E-12 | 8.31E-13 | 2.75E-13 | 1.15E-13 | 6.87E-14 | |

G29 | 9.46E-12 | 3.37E-12 | 2.58E-12 | 2.20E-12 | 6.88E-13 | 1.60E-13 | |

G31 | 9.02E-12 | 3.62E-12 | 2.55E-12 | 1.91E-12 | 7.25E-13 | 2.54E-13 |

## Conclusions

The author presents the stability of satellite clocks based on different reference clock types. 1-Hz GNSS data in 2-h observation interval is analysed using three different reference clocks: internal, caesium and h-maser oscillators. Reference clock stability is analysed in a 2-week period on the basis of 30-s IGS products that show that the h-maser clock stability is better by one order of magnitude than the internal clock and by half of one order of magnitude than the caesium one. The clock parameters are estimated epoch by epoch using a back-substitution steps method described in the text. Research shows a close correlation between the reference clock and the estimated clock stability. Internal oscillator shows close to 1E-12-s stability, caesium one 1.5E-13 s and h-maser 6E-13 s. Studies also show no connection between launch date of satellite, block type or frequency standard and satellite clock stability. These results should be incorporated into future satellite clock determination elaborations for short-term analyses with high interval observations.

## Notes

### Funding information

The paper is supported by project numbers 11.11.150.444 and 15.11.150.397.

## References

- Alcay S, Inal C, Yigit CO (2012a) Contribution of GLONASS observations on precise point positioning. FIG Working Week:6–10Google Scholar
- Alcay S, Inal C, Yigit C, Yetkin M (2012b) Comparing GLONASS-only with GPS-only and hybrid positioning in various length of baselines. Acta Geodaetica et Geophysica Hungarica 47:1–12. https://doi.org/10.1556/AGeod.47.2012.1.1. CrossRefGoogle Scholar
- Allan DW (1983) Clock characterization tutorial. In: Proceedings of the 15th annual precise time and time interval (PTTI) applications and planning meeting, pp 459–475Google Scholar
- Allan DW (1987) Time and frequency (time-domain) characterization, estimation, and prediction of precision clocks and oscillators. IEEE Trans Ultrason Ferroelectr Freq Control 34:647–654. https://doi.org/10.1109/T-UFFC.1987.26997 CrossRefGoogle Scholar
- Allan DW, Hellwig H, Kartaschoff P, Vanier J, Vig J, Winkler GMR, Yannoni N Standard terminology for fundamental frequency and time metrology, in: Proceedings of the 42nd Annual Frequency Control Symposium, 1988, IEEE, 1988: pp. 419–425. doi: https://doi.org/10.1109/FREQ.1988.27634.
- Beutler G, Moore AW, Mueller II (2009) The international global navigation satellite systems service (IGS): development and achievements. J Geod 83:297–307. https://doi.org/10.1007/s00190-008-0268-z CrossRefGoogle Scholar
- Bock H, Dach R, Jäggi A, Beutler G (2009) High-rate GPS clock corrections from CODE: support of 1 Hz applications. J Geod 83:1083–1094. https://doi.org/10.1007/s00190-009-0326-1 CrossRefGoogle Scholar
- Dach R, Walser P (2013) Bernese GNSS Software Version 5:2Google Scholar
- Gendt G (2007) Combined IGS clocks with 30 second sampling rate, [IGSMAIL-5525]. https://lists.igs.org/pipermail/igsmail/2007/006896.html.
- Gong H, Yang W, Wang Y, Zhu X (2013) Comparison of short-term stability estimation methods of GNSS on-board clock, in: J. Sun, W. Jiao, H. Wu, C. Shi (Eds.), China Satellite Navigation Conference (CSNC) 2013 Proceedings, Springer Berlin Heidelberg, Berlin, Heidelberg, pp. 503–513. doi: https://doi.org/10.1007/978-3-642-37407-4.
- Han S-C, Kwon JH, Jekeli C (2001) Accurate absolute GPS positioning through satellite clock error estimation. J Geod 75:33–43. https://doi.org/10.1007/s001900000151 CrossRefGoogle Scholar
- Kaloop MR, Rabah M (2016) Time and frequency domains response analyses of April 2015 Greece’s earthquake in the Nile Delta based on GNSS-PPP. Arab J Geosci 9:316. https://doi.org/10.1007/s12517-016-2343-8 CrossRefGoogle Scholar
- Kouba J, Héroux P (2001) Precise point positioning using IGS orbit and clock products. GPS Solutions 5:12–28CrossRefGoogle Scholar
- Krawinkel T, Schön S (2016) Benefits of receiver clock modeling in code-based GNSS navigation. GPS Solutions 20:687–701. https://doi.org/10.1007/s10291-015-0480-2 CrossRefGoogle Scholar
- Krzyżek R (2015) Routing corners of building structures – by the method of vector addition – measured with RTN GNSS surveying technology. Artificial Satellites 50:181–200. https://doi.org/10.1515/arsa-2015-0015 CrossRefGoogle Scholar
- Li M, Zhang S, Hu Y, He L (2016) Ultra-short-term stability analysis of GNSS clocks. In: Sun J, Liu J, Fan S, Wang F (eds) China satellite navigation conference (CSNC) 2016 proceedings: volume III. Springer Singapore, Singapore, pp 111–119. https://doi.org/10.1007/978-981-10-0940-2 CrossRefGoogle Scholar
- Lou Y, Zheng F, Gu S, Wang C, Guo H, Feng Y (2016) Multi-GNSS precise point positioning with raw single-frequency and dual-frequency measurement models. GPS Solutions 20:849–862. https://doi.org/10.1007/s10291-015-0495-8 CrossRefGoogle Scholar
- Loyer S, Perosanz F, Mercier F, Capdeville H, Mezerette A (2016) CNES/CLS IGS analysis center: contribution to MGEX and recent activities. In: IGS workshop 2016Google Scholar
- Maciuk K (2016a) The study of seasonal changes of permanent stations coordinates based on weekly EPN solutions. Artif Satellites 51:1–18. https://doi.org/10.1515/arsa-2016-0001 CrossRefGoogle Scholar
- Maciuk K (2016b) Different approaches in GLONASS orbit computation from broadcast ephemeris. Geodetski Vestnik 60:455–466. https://doi.org/10.15292/geodetski-vestnik.2016.03.455-466 CrossRefGoogle Scholar
- Maciuk K (2018a) GPS-only, GLONASS-only and combined GPS+GLONASS absolute positioning under different sky view conditions. Tehnicki Vjesnik - Technical Gazette 25. https://doi.org/10.17559/TV-20170411124329
- Maciuk K (2018b) Advantages of combined GNSS processing involving a limited number of visible satellites. Sci J Silesian Univ Technol Series Transp 98:89–99. https://doi.org/10.20858/sjsutst.2018.98.9 CrossRefGoogle Scholar
- Montenbruck O, Rizos C, Weber R, Weber G, Neilan R, Hugentobler U (2013) Getting a grip on multi-GNSS: the international GNSS service MGEX campaign. GPS World 24:44–49Google Scholar
- Petovello MG, Lachapelle G (2000) Estimation of clock stability using GPS. GPS Solutions 4:21–33. https://doi.org/10.1007/PL00012825 CrossRefGoogle Scholar
- Prange L, Orliac E, Dach R, Arnold D, Beutler G, Schaer S, Jäggi A (2017a) CODE’s five-system orbit and clock solution—the challenges of multi-GNSS data analysis. J Geod 91:345–360. https://doi.org/10.1007/s00190-016-0968-8 CrossRefGoogle Scholar
- Prange L, Schaer S, Villiger A (2017b) CODE MGEX (COM) product update, [IGSMAIL-7515]. https://lists.igs.org/pipermail/igsmail/2017/001350.html.
- Ruan R, Wei Z, Jia X (2017) Estimation, validation, and application of 30-s GNSS clock corrections. In: Sun J, Liu J, Yang Y, Fan S, Yu W (eds) China satellite navigation conference (CSNC) 2017 proceedings: volume III. Springer Singapore, Singapore, pp 21–36. https://doi.org/10.1007/978-981-10-4594-3 CrossRefGoogle Scholar
- Şanlıoğlu İ, Zeybek M, Özer Yiğit C (2016) Landslide monitoring with GNSS-PPP on steep-slope and forestry area: Taşkent landslide, in: ICENS International Conference on Engineering and Natural Science, pp. 1–7.Google Scholar
- Soycan M (2011) A quality evaluation of precise point positioning within the Bernese GPS software version 5.0. Arab J Sci Eng 37:147–162. https://doi.org/10.1007/s13369-011-0162-5 CrossRefGoogle Scholar
- Szombara S, Maciuk K (2017) Stability of permanent EPN stations near the Baltic Sea shoreline, in: 2017 Baltic Geodetic Congress (BGC Geomatics), IEEE, Gdańsk, pp. 317–320. doi: https://doi.org/10.1109/BGC.Geomatics.2017.36.
- Uhlemann M, Gendt G, Ramatschi M, Deng Z (2015) GFZ global multi-GNSS network and data processing results. In: IAG 150 years, pp 673–679. https://doi.org/10.1007/1345_2015_120. CrossRefGoogle Scholar
- Xu P, Shi C, Fang R, Liu J, Niu X, Zhang Q, Yanagidani T (2013) High-rate precise point positioning (PPP) to measure seismic wave motions: an experimental comparison of GPS PPP with inertial measurement units. J Geod 87:361–372. https://doi.org/10.1007/s00190-012-0606-z CrossRefGoogle Scholar
- Zhang X, Li X, Guo F (2011) Satellite clock estimation at 1 Hz for realtime kinematic PPP applications. GPS Solutions 15:315–324. https://doi.org/10.1007/s10291-010-0191-7 CrossRefGoogle Scholar
- Zheng J, Guo M, Xiong C, Xiao Y (2017) Comparison and evaluation of satellite performance based on different clock products. In: Sun J, Liu J, Yang Y, Fan S, Yu W (eds) China satellite navigation conference (CSNC) 2017 proceedings: volume III. Springer Singapore, Singapore, pp 577–590. https://doi.org/10.1007/978-981-10-4594-3 CrossRefGoogle Scholar

## Copyright information

**Open Access** This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.