Advertisement

International Journal of Material Forming

, Volume 12, Issue 1, pp 89–96 | Cite as

A proposal improvement in flatness measurement in strip rolling

  • Sami AbdelkhalekEmail author
Original Research
  • 50 Downloads

Abstract

In strip rolling flatness of the final product is controlled inline with a roll sensor placed at the outgoing of the tandem mill to measure the longitudinal (in the rolling direction) internal stress profile throughout the coil. This profile involves resultant force and sometimes resultant moment (due to preset anomaly for example) equilibrated by the coiler. When strip is relaxed these two quantities are eliminated and there remain residual stresses in the strip. Since negative residual stresses are the main origin of defects, operators subtract the resultant force from measurements to visualize the residual stress profile in real time and detect negative values, without considering the resultant moment. In this paper we show that to predict flatness defects correctly we have to subtract resultant moment too. Otherwise, unpredictable defects manifest in the delivered product.

Keywords

Post buckling Asymptotic numerical method Residual stress Flatness defect Strip rolling 

Notes

Acknowledgments

Author wish to thank Arcelormittal company for providing measurements and Pierre Montmitonnet for helpful and comments on the paper.

Compliance with ethical standards

Conflict of interest

The authors declare that they have no conflict of interest.

References

  1. 1.
    Molleda J, Usamentiaga R, García D (2013) On-line flatness measurement in the steelmaking industry. Sensors 13(12):10245–10272.  https://doi.org/10.3390/s130810245 CrossRefGoogle Scholar
  2. 2.
    Abdelkhalek S, Zahrouni H, Legrand N, Potier-Ferry M (2015) Post-buckling modeling for strips under tension and residual stresses using asymptotic numerical method. Int J Mech Sci 104:126–137.  https://doi.org/10.1016/j.ijmecsci.2015.10.011 CrossRefGoogle Scholar
  3. 3.
    Zahrouni H, Cochelin B, Potier-Ferry M (1999) Computing finite rotations of shells by an asymptotic-numerical method. Comput Methods Appl Mech Eng 175(1-2):71–85.  https://doi.org/10.1016/S0045-7825(98)00320-X CrossRefzbMATHGoogle Scholar
  4. 4.
    Büchter N, Ramm E, Roehl D (1994) Three-dimensional extension of non-linear shell formulation based on the enhanced assumed strain concept. Int J Numer Methods Eng 37(15):2551–2568.  https://doi.org/10.1002/nme.1620371504 CrossRefzbMATHGoogle Scholar
  5. 5.
    Boutyour EH, Zahrouni H, Potier-Ferry M, Boudi M (2004) Bifurcation points and bifurcated branches by an asymptotic numerical method and Padé approximants. Int J Numer Methods Eng 60(12):1987–2012.  https://doi.org/10.1002/nme.1033 CrossRefzbMATHGoogle Scholar
  6. 6.
    Kanemori S, Kinose R, Maniwa S et al (2014) Development of strip shape meter with high accuracy under severe conditions of hot strip mill. Mitsubishi Heavy Ind Tech Rev 51:27–31Google Scholar
  7. 7.
    Molleda J, Usamentiaga R, García DF, Bulnes FG (2010) Real-time flatness inspection of rolled products based on optical laser triangulation and three-dimensional surface reconstruction. J Electron Imaging 19(3):31206.  https://doi.org/10.1117/1.3455987 CrossRefGoogle Scholar
  8. 8.
    Tsuzuki S, Yoichi K, Kenji M (2009) Flatness control system of cold rolling Processwith pneumatic bearing type shape roll. IHI Eng Rev 42:54–60Google Scholar

Copyright information

© Springer-Verlag France SAS, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Military academy of Fondouk JedidNabeulTunisia
  2. 2.Applied Mechanics and Systems Research Laboratory, Tunisia Polytechnic SchoolUniversity of CarthageLa MarsaTunisia

Personalised recommendations