Advertisement

Journal of Mechanical Science and Technology

, Volume 32, Issue 11, pp 5233–5239 | Cite as

Design of anti-vibration mounting for 140A class alternator for vehicles

  • Zhen Qin
  • Hyoung-il Son
  • Sung-Ki Lyu
Article
  • 4 Downloads

Abstract

The alternator is a core component of modern vehicles that supplies power to all the electrical equipment when the engine is running. It is fitted to the engine bracket with long bolts going through the frame mountings. Due to the strong vibration from the engine, it is extremely important to improve its anti-vibration performance to extend the life of the alternator. This study presents a new anti-vibration mounting design for the alternator frame based on a 140A class alternator used in a best-selling sport utility vehicle (SUV). In this study, UG (unigraphics NX) was used to generate 3D models of the alternator and the finite element analysis software ABAQUS was used to simulate the vibration experiment. Then through a series of verification experiments, results were obtained which show that the new separated mounting design has obvious improvements in terms of the anti-vibration characteristic, as compared to the current design. The current work will be used for resonance reduction during design stages in future works.

Keywords

Alternator frame Mounting Generator Anti-vibration Vibration durability FEM PSD (power spectral density) profile 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. [1]
    C. Parmar, S. Tyagarajan, S. Tiwari, R. Thonge and S. A. Paul, Thermal protection of rear mounted engine and its components using a ventilation fan with unique monitoring and fault diagnosis technique, SAE Technical Papers, 982768, 1998 982768, 1998 982768 (1998).Google Scholar
  2. [2]
    F. A. Santana, F. L. A. Dos Anjos, R. R. Ripoli, N. Kai and N. Shiraiwa, Durability analysis of a pulley /Alternator support for power transmission in commercial vehicles, SAE Technical Papers, 90806 (2001).CrossRefGoogle Scholar
  3. [3]
    M. W. Crull and R. H. Johnston, Future requirements for alternators, SAE Technical Papers, 90142 (1998).Google Scholar
  4. [4]
    D. G. Kim and S. C. Kim, An analysis study for thermal design of ISG (Integrated Starter & Generator) for hybrid electric vehicle, Transaction of the Korean Society of Automotive Engineers, 21 (4) (2013) 120–127.CrossRefGoogle Scholar
  5. [5]
    S. C. Kim, Thermal design and analysis evaluation of ISG motor for hybrid electric vehicles considering high–speed driving condition, Transaction of the Korean Society of Automotive Engineers, 22 (1) (2014) 59–64.CrossRefGoogle Scholar
  6. [6]
    Q. Wang, K. Rajashekara, Y. Jia and J. Sun, A real–time vibration suppression strategy in electric vehicles, IEEE Trans. Veh. Technol., 66 (9) (2017) 7722–7729.CrossRefGoogle Scholar
  7. [7]
    J. Lu, Z. Zhan, H. Song, X. Liu, X. Yang and J. Yang, Design optimization of vehicle body NVH performance based on dynamic response analysis, SAE Technical Papers, 90142 (1998).Google Scholar
  8. [8]
    M. A. Panza, A review of experimental techniques for NVH analysis on a commercial vehicle, Energy Procedia, 82 (2015) 1017–1023.CrossRefGoogle Scholar
  9. [9]
    J. Wang, C. Shi, N. Yang, H. Sun, Y. Liu and B. Song, Strength, stiffness, and panel peeling strength of carbon fiber–reinforced composite sandwich structures with aluminum honeycomb cores for vehicle body, Compos. Struct., 184 (2018) 1189–1196.CrossRefGoogle Scholar
  10. [10]
    Y. Cao, H. Xia and Z. Li, A semi–analytical/FEM model for predicting ground vibrations induced by high–speed train through continuous girder bridge, J. Mech. Sci. Technol., 26 (8) (2012) 2485–2496.CrossRefGoogle Scholar
  11. [11]
    M. Choi, Free vibration analysis of plate structures using finite element–transfer stiffness coefficient method, KSME Int. J., 17 (6) (2003), 805–815.Google Scholar
  12. [12]
    J. Ooi, X. Wang, C. Tan, J. Ho and Y. P. Lim, Modal and stress analysis of gear train design in portal axle using finite element modeling and simulation, J. Mech. Sci. Technol., 26 (2) (2012) 575–589.CrossRefGoogle Scholar
  13. [13]
    T. Xiang, D. Lan, S. Zhang, W. Li and D. Lin, Experimental modal test of the spiral bevel gear wheel using the Poly–MAX method, J. Mech. Sci. Technol., 32 (1) (2018) 21–28.CrossRefGoogle Scholar
  14. [14]
    M. V. Santosh, K. R. Suresh and S. Kiran Aithal, Mechanical characterization and microstructure analysis of Al C355.0 by sand casting, Die Casting and Centrifugal Casting Techniques. Mater. Today Proc., 4 (10) (2017) 10987–10993.Google Scholar
  15. [15]
    S. C. Huang, Application of operational deflection shapes technology in the textile machine, Journal of Xian University of Engineering Science & Technology, China (1989).Google Scholar

Copyright information

© The Korean Society of Mechanical Engineers and Springer-Verlag GmbH Germany, part of Springer Nature 2018

Authors and Affiliations

  1. 1.School of Mechanical and Aerospace Engineering, ReCAPTGyeongsang National UniversityJinjuKorea
  2. 2.R&D CenterErae Automotive System Co., LtdDaeguKorea

Personalised recommendations