Journal of Mechanical Science and Technology

, Volume 31, Issue 1, pp 445–454 | Cite as

The effect of hub leakage on the aerodynamic performance of high-pressure steam turbine stages

  • Jeong Jin Lee
  • Soo Young Kang
  • Tong Seop Kim
  • Seong Jin Park
  • Gi Won Hong
Article
First Online:
Received:
Revised:
Accepted:

Abstract

In a steam turbine, leakage occurs at the gap between the rotor shafts and diaphragms and is injected into the main stream at the inlet of the rotor blade. Although this hub leakage flow is small, it affects the main flow, especially in the rotor passage. This study uses computational fluid dynamics to investigate the influence of hub leakage flow re-entry on the aerodynamic performance of turbine stages of a 10-stage high-pressure steam turbine operating at USC conditions. Each stage was individually investigated in regard to the influence of stage reaction on the efficiency drop. The flow field of the turbine without the leakage flow was analyzed first, and then the variations in flow phenomena and stage efficiency were investigated with increasing leakage flow ratio. Our analysis shows that the efficiency drop depends strongly on the stage reaction. The first stage designed with 21 % reaction showed an efficiency drop of approximately 1 % for 1 % increase in leakage flow, which is almost twice that of the last three stages with an average stage reaction of 48 %.

Keywords

Computational fluid dynamics Hub seal leakage Stage efficiency Stage reaction Steam turbine Ultra-supercritical 
This is a preview of subscription content, log in to check access.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. [1]
    World energy outlook, International energy agency (2015) 49-74.Google Scholar
  2. [2]
    T. Sasaki, TOSHIBA's energy solution, Japan-Poland Clean Coal Seminar, Warszawa, Szwolezerow, Poland (2014).Google Scholar
  3. [3]
    J. Zachary, Steam turbine design consideration for ultrasupercritical cycles, ASME paper, GT2010-22317 (2010).Google Scholar
  4. [4]
    N. Okita, T. Sasaki, T. Suga and S. Iwai, Development and strategy for A-USC steam turbine cycle, ASME paper, GT2011-45549 (2011).CrossRefGoogle Scholar
  5. [5]
    A. Tremmel, Siemens reference power plant design applied for ultra-supercritical steam power plant Luenen in Germany, POWER-GEN India, New Dehli, India (2012).Google Scholar
  6. [6]
    R. Quikertz, A. Ulma, E. Gobercht and M. Wechsung, USC Steam Turbine technology for maximum efficiency and operational flexibility, POWER-GEN Asia 2008, Kuala Lumpur, Malaysia (2008).Google Scholar
  7. [7]
    N. Lückemeyer, H. Kirchner and H. Almstedt, Challenges in advanced-USC steam turbine design for 1300°F / 700°C, ASME Paper, GT2012-69822 (2012).Google Scholar
  8. [8]
    A. F. Armor, Ultrasupercritical steam turbines: Design and materials issues for the next generation, EPRI Report, 1006844 (2002).Google Scholar
  9. [9]
    W. Kosman, M. Roskosz and K. Nawrat, Thermal elongations in steam turbines with welded rotors made of advanced materials at supercritical steam parameter, Applied Thermal Engineering, 29 (16) (2009) 3386–3393.CrossRefGoogle Scholar
  10. [10]
    J. Shingledecker and R. Purgert, Steam turbine materials for advanced Ultrasupercritical(AUSC) coal power plant, 2014 NETL Crosscutting Research Review Meeting, Pittsburgh, PA, USA (2014).Google Scholar
  11. [11]
    L. Zhou, G. Xu, C. Xu, Y. Yang, Y. Li and J. Deng, Optimum design of a double reheat steam system in an ultra supercritical unit, ASME Paper, GT2013-95190 (2013).Google Scholar
  12. [12]
    H. J. Jang, S. Y. Kang, J. J. Lee, T. S. Kim and S. J. Park, Performance analysis of a multi-stage ultra supercritical steam turbine using computational fluid dynamics, Applied Thermal Engineering, 87 (2015) 352–361.CrossRefGoogle Scholar
  13. [13]
    Y. S. Hong and F. G. Groh, Axial turbine loss analysis and efficiency prediction method, Boeing Report, D4-3220 (1966).Google Scholar
  14. [14]
    A. Yamamoto, Endwall/flow loss mechanism in a Linear cascade with blade tip clearance, J. of Turbomachinery, 111 (1989) 264–275.CrossRefGoogle Scholar
  15. [15]
    J. H. Cheon and S. W. Lee, Tip leakage aerodynamics over the cavity squealer tip equipped with full coverage winglets in a turbine cascade, International Journal of Heat and Fluid Flow, 56 (2015) 60–70.CrossRefGoogle Scholar
  16. [16]
    J. I. Cofer, J. K. Reinker and W. J. Sumner, Advances in Steam Turbine Path Technology, General Electric Report GER-3713E (1996).Google Scholar
  17. [17]
    J. Gao, Q. Zheng, T. Xu and P. Dong, Inlet conditions effect on tip leakage vortex breakdown in unshrouded axial turbines, Energy, 91 (2015) 255–263.CrossRefGoogle Scholar
  18. [18]
    S. H. Yoon, The effect of the degree of reaction on the leakage loss in steam turbines, J. Eng. Gas Turbines Power, 135 (2) (2013) 022602.MathSciNetCrossRefGoogle Scholar
  19. [19]
    S. L. Dixon and C. A. Hall, Fluid Mechanics and thermodynamics of turbomachinery, 7th Ed., Butterworth-Heinemann, Oxford, UK (2013).Google Scholar
  20. [20]
    ANSYS Inc., ANSYS CFX 14.0.Google Scholar
  21. [21]
    R. Culver and F. Liu, Mixing-plane method for flutter computation in multi-stage turbomachines, 47th AIAA Aerospace Science Meeting Including the New Horizons Forum and Aerospace Exposition, Orlando, Florida, USA (2009).Google Scholar
  22. [22]
    The International Association for the Properties of Water and Steam, Release on the IAPWS industrial formulation 1997 for the thermodynamic properties of water and steam (1997).Google Scholar
  23. [23]
    MentorGraphics Inc., Flowmaster V7.9 (2010).Google Scholar
  24. [24]
    D. G. Ainley, Performance of axial flow turbines, Proceeding of Institution of Mechanical Engineers, 159 (1948) 230–244.CrossRefGoogle Scholar
  25. [25]
    K. C. Cotton, Evaluating and improving steam turbine performance, 2nd Ed., Cotton Fact Inc., New York (1998).Google Scholar

Copyright information

© The Korean Society of Mechanical Engineers and Springer-Verlag Berlin Heidelberg 2017

Authors and Affiliations

  • Jeong Jin Lee
    • 1
  • Soo Young Kang
    • 1
  • Tong Seop Kim
    • 2
  • Seong Jin Park
    • 3
  • Gi Won Hong
    • 3
  1. 1.Graduate SchoolInha UniversityIncheonKorea
  2. 2.Dept. of Mechanical Engineering, Inha UniversityInha UniversityIncheonKorea
  3. 3.Turbine Performance TeamDoosan Heavy Industries & ConstructionChangwonKorea

Personalised recommendations