Advertisement

Effect of elastic modulus and position of polyurea coating on flexural strength of coated ceramic tiles by experiments and finite element analysis

  • Kanittha KamonchaivanichEmail author
  • Keiichi Kuboyama
  • Toshiaki Ougizawa
Article
  • 20 Downloads

Abstract

The mechanism of a polyurea coating on the flexural strength of coated ceramic tiles was studied by three-point bending together with FEM simulation. The influence of Young’s modulus and the coating position of the polyurea on the coated ceramic sample were investigated. The back-coated ceramic with lower modulus polyurea (PUR240 MPa) could show higher flexural strength due to the cushion effect that reduces tensile stress around the bottom center of the substrate. The higher modulus polyurea coating (PUR866 MPa) has a significant influence on the flexural strength of the coated ceramic sample. In back-coating, the higher modulus coating increased the flexural strength of the coated ceramic sample by nearly twofold, compared to lower modulus. This higher modulus coating enhanced the stress distribution as well as storage energy in the sample. According to the results of the FEM simulation, the mechanism which influences the stress distribution within samples during the three-point bending test was investigated. The cushion effect shows a main contribution in stress distribution by a lower modulus coating. The cushion effect occurs near the supporting pins and contributes to the stress dissipation and the reduction of stress concentration at the center-bottom of the substrate. In contrast, a thickening effect plays an important role in the case of higher modulus polyurea coatings. The center-back-coated with higher modulus polyurea acts to increase the thickness of the ceramics and dominates the effect on the flexural strength of the coated ceramic sample.

Keywords

Polyurea Elastic modulus Ceramic tile Fracture FEM simulation 

Supplementary material

11998_2018_170_MOESM1_ESM.docx (9.7 mb)
Supplementary material 1 (DOCX 9961 kb)

References

  1. 1.
    Primeaux II, DJ, “Spray Polyurea—Versatile High Performance Elastomer for the Polyurethane Industry”, Polyurethanes’89, the 32nd Technical/Marketing Conference, SPI, San Francisco, California, October 1989Google Scholar
  2. 2.
    Feng, L, Iroh, JO, “Corrosion Resistance and Lifetime of Polyimide-b-Polyurea Novel Copolymer Coating.” Prog. Org. Coat., 77 590–599 (2014)CrossRefGoogle Scholar
  3. 3.
    LeBlanc, J, Gardner, N, Shukla, A, “Effect of Polyurea Coatings on the Response of Curved E-Glass/Vinyl Ester Composite Panels to Underwater Explosive Loading.” Compos. Part B, 44 565–574 (2013)CrossRefGoogle Scholar
  4. 4.
    Mohotti, D, Ngo, T, Raman, SN, Ali, M, Mendis, P, “Plastic Deformation of Polyurea Coated Composite Aluminium Plates Subjected to Low Velocity Impact.” Mater. Des., 56 696–713 (2014)CrossRefGoogle Scholar
  5. 5.
    Broekaert, M, “Modified MDI-Prepolymers Improve the Initial Physical Properties and Reduce the ‘In-Service’ Time of Aromatic Polyurea Coatings.” Proceedings of the 6th Nurnberg CongressCreative Advances in Coatings Technology, Nurnberg April 2001, p. 761.Google Scholar
  6. 6.
    Xue, L, Mock, W, Jr, Belytschko, T, “Penetration of DH-36 Steel Plates with and Without Polyurea Coating.” Mech. Mater., 42 981–1003 (2010)CrossRefGoogle Scholar
  7. 7.
    Toutanji, HA, Choi, H, Wong, D, Gilbert, JA, Alldredge, DJ, “Applying a Polyurea Coating to High-Performance Organic Cementitious Materials.” Constr. Build. Mater., 38 1170–1179 (2013)CrossRefGoogle Scholar
  8. 8.
    Grujicic, M, Pandurangan, B, He, T, Cheeseman, BA, Yen, CF, Randow, CL, “Computational Investigation of Impact Energy Absorption Capability of Polyurea Coatings via Deformation-Induced Glass Transition.” Mater. Sci. Eng. A, 527 7741–7751 (2010)CrossRefGoogle Scholar
  9. 9.
    Barsoum, R, “Dynamic Response and Failure Mechanisms of Layered Ceramic-Elastomer-Polymer/Metal Composites”, pp. 2–4. University of California (2010)Google Scholar
  10. 10.
    Imbalzano, G, Ngo, T, Tran, P, “A Numerical Study of Auxetic Composite Panels Under Blast Loadings.” Compos. Struct., 135 339–352 (2015)CrossRefGoogle Scholar
  11. 11.
    Imbalzano, G, Tran, P, Ngo, TD, Lee, PVS, “Three-Dimensional Modelling of Auxetic Sandwich Panels for Localised Impact Resistance.” J. Sandw. Struct. Mater., 19 (3) 291–316 (2015)CrossRefGoogle Scholar
  12. 12.
    Raman, SN, Ngo, T, Lu, J, Mendis, P, “Experimental Investigation on the Tensile Behavior of Polyurea at High Strain Rates.” Mater. Des., 50 124–129 (2013)CrossRefGoogle Scholar
  13. 13.
    Mohotti, D, Ngo, T, Mendis, P, Raman, SN, “Polyurea Coated Composite Aluminium Plates Subjected to High Velocity Projectile Impact.” Mater. Des., 52 1–16 (2013)CrossRefGoogle Scholar
  14. 14.
    Taylor, JR, Bull, AC, “Ceramics Glaze Technology.” Chapter 7 in Glaze Formation, pp. 125. Institute of Ceramics & Pergamon Press, New York (1986)Google Scholar
  15. 15.
    Ryan, W, Radford, C, “Whitewares.” Testing and Quality Control, Institute of Ceramics & Pergamon Press, New York (1987)Google Scholar
  16. 16.
    Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature, ASTM C1161-13Google Scholar
  17. 17.
    Green, DJ, “An Introduction to the Mechanical Properties of Ceramics.” Chapter 9 in Strengthend Engineering Design, pp. 286–288. Cambridge University Press, UK (1998)Google Scholar
  18. 18.
    Riccardi, CC, Vallo, CI, “Estimation of Weibull Parameters for the Flexural Strength of PMMA-Based Bone Cements.” Polym. Eng. Sci., 42 (6) 1260–1273 (2002)CrossRefGoogle Scholar
  19. 19.
    Bhaduri, A, “Mechanical Properties and Working of Metals and Alloys.” Chapter 2 in Compression, pp. 98–106. Springer, Singapore (2018)Google Scholar
  20. 20.
    Schoenfelder, S, Ebert, M, Landesberger, C, Bock, K, Bagdahn, J, “Investigations of the Influence of Dicing Techniques on the Strength Properties of Thin Silicon.” J. Microelectron. Reliab., 47 (2–3) 168–178 (2007)CrossRefGoogle Scholar
  21. 21.
    Hafeez, F, Arif, M, “Engineering Practical Book Vol-II: Basic Mechanics and Science of Materials.” pp. 62–65. Educreation Publishing, New Delhi (2011)Google Scholar
  22. 22.
    Davidge, RW, “Mechanical Behaviour of Ceramics.” Chapter 9 in Engineering Design Data, pp. 152. Cambridge, New York (1979)Google Scholar
  23. 23.
    Greaves, GN, Greer, AL, Lakes, RS, Rouxel, T, “Poisson’s Ratio and Modern Materials.” Nat. Mater., 10 823–837 (2011)CrossRefGoogle Scholar
  24. 24.
    Orlov, V, “Computer Simulation of Optimal Thickness of Polyurea Coating Using for Trenchless Renovation of Potable Water Pipes.” J. Procedia Eng., 165 1168–1175 (2016)CrossRefGoogle Scholar

Copyright information

© American Coatings Association 2019

Authors and Affiliations

  • Kanittha Kamonchaivanich
    • 1
    Email author
  • Keiichi Kuboyama
    • 1
  • Toshiaki Ougizawa
    • 1
  1. 1.Department of Chemistry and Materials ScienceTokyo Institute of TechnologyTokyoJapan

Personalised recommendations