Advertisement

Journal of Marine Science and Application

, Volume 16, Issue 4, pp 427–445 | Cite as

Review of ship slamming loads and responses

  • Shan Wang
  • C. Guedes Soares
Article

Abstract

The paper presents an overview of studies of slamming on ship structures. This work focuses on the hull slamming, which is one of the most important types of slamming problems to be considered in the ship design process and the assessment of the ship safety. There are three main research aspects related to the hull slamming phenomenon, a) where and how often a slamming event occurs, b) slamming load prediction and c) structural response due to slamming loads. The approaches used in each aspect are reviewed and commented, together with the presentation of some typical results. The methodology, which combines the seakeeping analysis and slamming load prediction, is discussed for the global analysis of the hull slamming of a ship in waves. Some physical phenomena during the slamming event are discussed also. Recommendations for the future research and developments are made.

Keywords

review slamming probability ship slamming hydroelasticity 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgement

Individuals or units other than authors who were of direct help in the work should be acknowledged by a brief statement following the text

References

  1. Aarsnes JV, 1996. Drop test with ship sections-effect of roll angle. Report 603834.00.01. Norwegian Marine Technology Research Institute, Trondheim.Google Scholar
  2. Alexandru I, Brizzolara S, Viviani M, Couty N, Donner R, Hermundstad O, Kukkanen T, Malenica S, Termarel P, 2007. Comparison of experimental and numerical impact loads on ship-like sections. In: Guedes Soares C, Das PK (Eds). Advancements in Marine Structures. Taylor and Francis, London, 339–349.Google Scholar
  3. Algarín R, Bula A, Tascón O, 2011. CFD modeling of 2D asymmetric entry impact along with horizontal velocity. Ship Science & Technology, 5(9), 99–106.Google Scholar
  4. Aly AM, Asai M, Sonoda Y, 2011. Simulation of free falling rigid body into water by a stabilized incompressible SPH method. Ocean Systems Engineering, 1(3), 207–222.CrossRefGoogle Scholar
  5. Amin W, 2009. Non-linear unsteady wave loads on large high speed wave piercing catamarans. PhD Thesis, School of Engineering, University of Tasmania, Hobart, TAS, Australia.Google Scholar
  6. Aquelet N, Souli M, Olovsson L, 2006. Euler–Lagrange coupling with damping effects: Application to slamming problems. Computer Methods in Applied Mechanics and Engineering, 195(1), 110–132.MathSciNetzbMATHCrossRefGoogle Scholar
  7. Armand JL, Cointe R, 1987. Hydrodynamic impact analysis of a cylinder. Proc. Fifth Inter. Offshore Mech. and Arctic Engng. Symp, Tokyo, Japan, 1, 609–634.Google Scholar
  8. Attfield K, 1975. Gas platforms - How designers underestimated the North Sea. Offshore Technology, 12–22.Google Scholar
  9. Baarholm R, Faltinsen OM, Herfjord, K. Wave impact on decks of floating platforms. Practical Design of Ships and Other Floating Structures. Proceedings of the Eighth International Symposium on Practical Design of Ships and Other Floating Structures.Google Scholar
  10. Barjasteh M, Zeraatgar H, Javaherian MJ, 2016. An experimental study on water entry of asymmetric wedges. Applied Ocean Research, 58, 292–304.CrossRefGoogle Scholar
  11. Battistin D, Iafrati A, 2003. Hydrodynamic loads during water entry of two-dimensional and axisymmetric bodies. J. Fluids Struct., 17, 643–664.CrossRefGoogle Scholar
  12. Belik O, Bishop RED, Price WG, 1983. A simulation of ship responses due to slamming in irregular head waves. Trans. R. Inst. Naval Archit., 125, 237–254.Google Scholar
  13. Bishop RED, Price WG, 1974. On the modal analysis of ship strength. Proceedings of the Royal Society of London, A 341, 121–134.zbMATHCrossRefGoogle Scholar
  14. Bishop RED, Price WG, 1979. Hydroelasticity of Ships. Cambridge University Press, London, UK.Google Scholar
  15. Boesten E, 2006. The M/S Estonia disaster and the treatment of human remains. In: Bierens JJLM (Eds.): Handbook on Drowning, 650–652.Google Scholar
  16. Cheon JS, Jang BS, Yim KH, Lee HD, Koo BY, Ju, H, 2016. A study on slamming pressure on a flat stiffened plate considering fluid–structure interaction. Journal of Marine Science and Technology, 21(2), 309–324.CrossRefGoogle Scholar
  17. Clauss GF, Klein M, Dudek M, 2011. Model test report-Test Campaign I (TCI)-Chemical Tanker (TUB), EXTREME SEAS project report (confidential).Google Scholar
  18. Colicchio G, Greco M, Miozzi M, Lugni C, 2009. Experimental and numerical investigation of the water-entry and water-exit of a circular cylinder. Proceedings of the 24th Int. Workshop on Water Waves and Floating Bodies, Zelenogorsk, Russia, 19–22.Google Scholar
  19. Corak M, Parunov J, Guedes Soares C, 2015. Probabilistic load combination factors of wave and whipping bending moments. Journal of Ship Research, 59(1), 11–30.CrossRefGoogle Scholar
  20. Das K, Batra RC, 2011. Local water slamming impact on sandwich composite hulls. Journal of Fluids and Structures, 27(4), 523–551.CrossRefGoogle Scholar
  21. Datta N, Siddiqui MA, 2016. Hydroelastic analysis of axially loaded Timoshenko beams with intermediate end fixities under hydrodynamic slamming loads. Ocean Engineering, 127, 124–134.CrossRefGoogle Scholar
  22. Davis MR, Whelan JR, 2007. Computation of wet deck bow slam loads for catamaran arched cross sections. Ocean Engineering, 34(17), 2265–2276.CrossRefGoogle Scholar
  23. De Backer G, Vantorre M, Beels C, 2009. Experimental investigation of water impact on axisymmetric bodies. Appl. Ocean Res., 31, 143–156.CrossRefGoogle Scholar
  24. Dhavalikar S, Awasare S, Joga R, Kar AR, 2015. Whipping response analysis by one way fluid structure interaction—A case study. Ocean Engineering, 103, 10–20.CrossRefGoogle Scholar
  25. Dobrovol’skaya ZN, 1969. On some problems of similarity flow of fluids with a free surface. Journal of Fluid Mechanics, 36, 805–829.zbMATHCrossRefGoogle Scholar
  26. El Malki Alaoui A, Nême A, Tassin A, Jacques N, 2012. Experimental study of coefficients during vertical water entry of axisymmetric rigid shapes at constant speeds. Appl. Ocean Res., 37, 183–197.CrossRefGoogle Scholar
  27. El Moctar O, Ley J, 2016. Computational fluid and structure dynamics methods to assess wave-induced loads and hydroelasticity effects. In: Guedes Saores C, Santos T A (Eds). Maritime Engineering and Technology 3, Taylor and Francis, 1, 19–27.CrossRefGoogle Scholar
  28. El Moctar O, Schellin TE, Priebe T, 2006. CFD and FE methods to predict wave loads and ship structural response. 26th Symp. Naval Hydrodynamics, Rome.Google Scholar
  29. Engle A, Lewis R, 2003. A comparison of hydrodynamic impacts prediction methods with two dimensional drop test data. Marine structures, 16(2), 175–182.CrossRefGoogle Scholar
  30. Facci AL, Panciroli R, Ubertini S, Porfiri M, 2015. Assessment of PIV-based analysis of water entry problems through synthetic numerical datasets. Journal of Fluids and Structures, 55, 484–500.CrossRefGoogle Scholar
  31. Facci AL, Porfiri M, Ubertini S, 2016. Three-dimensional water entry of a solid body: A computational study. Journal of Fluids and Structures, 66, 36–53.CrossRefGoogle Scholar
  32. Facci AL, Ubertini S, 2015. Numerical assessment of similitude parameters and dimensional analysis for water entry problems. Mathematical Problems in Engineering.Google Scholar
  33. Faltinsen OM, 1993. Sea loads on ships and offshore structures solutions. Cambridge University Press, Cambridge.Google Scholar
  34. Faltinsen OM, 1997. The effect of hydroelasticity on ship slamming. Philos. Trans. R. Soc. London A, 355, 575–591.zbMATHCrossRefGoogle Scholar
  35. Faltinsen OM, 1999. Water entry of a wedge by hydroelastic orthotropic plate theory. J. Ship Res., 43, 180–193.Google Scholar
  36. Faltinsen OM, 2000. Hydroelastic slamming. Journal of Marine Science and Technology, 5, 49–65.CrossRefGoogle Scholar
  37. Faltinsen OM, 2005. Hydrodynamics of high-speed marine vehicles. Cambridge University Press, Cambridge.Google Scholar
  38. Faltinsen OM, Kvalsvold J, Aarsnes JV, 1997. Water impact on a horizontal elastic plate. Journal of Marine Science and Technology, 2, 87–100.CrossRefGoogle Scholar
  39. Farsi M, Ghadimi P, 2016. Effect of flat deck on catamaran water entry through smoothed particle hydrodynamics. Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment, 230(2), 267–280.CrossRefGoogle Scholar
  40. Ferro G, Mansour AE, 1985. Probabilistic analysis of combined slamming and wave-induced responses. Journal of Ship Research, 29(3), 170–188.Google Scholar
  41. Fonseca N, Antunes E, Guedes Soares C, 2006. Whipping response of vessels with large amplitude motions. Proceedings of the 25th International Conference on Offshore Mechanics and Arctic Engineering, paper OMAE2006–92412.Google Scholar
  42. Fonseca N, Guedes Soares C, 1998a. Time domain analysis of large amplitude vertical motions and wave loads. Journal of Ship Research, 42(2), 100–113.Google Scholar
  43. Fonseca N, Guedes Soares C, 1998b. Non-linear wave induced responses of ships in irregular seas. ASME Proc 17th Int Conf on Offshore Mech. and Arctic Engin.(OMAE 98).Google Scholar
  44. French BJ, Thomas GA, Davis MR, 2015. Slam occurrences and loads of a high-speed wave piercer catamaran in irregular seas. J Engineering for the Maritime Environment, 229(1), 45–57.Google Scholar
  45. Friis-Hansen P, 1994. On combination of slamming and wave induced responses. Journal of Ship Research, 38(2), 104–114.Google Scholar
  46. Gadelho JFM, Karmakar D, Lavrov A, Guedes Soares C, 2015. CFD analysis of a rigid bottom fixed submerged plates. In: Guedes Soares C (Ed.). Renewable Energies Offshore. Taylor & Francis Group, London, 531–537.CrossRefGoogle Scholar
  47. Ghadimi P, Chekab MAF, Dashtimanesh A, 2014. Numerical simulation of water entry of different arbitrary bow sections. Journal of Naval Architecture and Marine Engineering, 11(2), 117–129.CrossRefGoogle Scholar
  48. Ghadimi P, Feizi Chekab MA, Dashtimanesh A, 2013. A numerical investigation of the water impact of an arbitrary bow section. ISH Journal of Hydraulic Engineering, 19(3), 186–195.CrossRefGoogle Scholar
  49. Gingold RA, Monaghan JJ, 1977. Smoothed particle hydrodynamics: theory and application to non-spherical stars. Royal Astronautical Society, 181: 375–389.zbMATHGoogle Scholar
  50. Greenhow M, Lin W, 1985. Numerical simulation of nonlinear free surface flows generated by wedge entry and wave maker motions. 4th International Conference on Numerical Ship Hydrodynamics, Washington, DC.Google Scholar
  51. Guedes Soares C, 1989. Transient response of ship hulls to wave impact. Int. Shipbuilding Progr., 36, 137–156.Google Scholar
  52. Guedes Soares C, Pascoal R, Antão EM, Voogt AJ, Buchner B, 2007. An approach to calculate the probability of wave impact on an FPSO bow. Journal of Offshore Mechanics and Arctic Engineering, 129(2), 73–80.CrossRefGoogle Scholar
  53. Guo BD, Qu QL, Wu JL, Liu PQ, 2013. Fluid-structure interaction modeling by ALE and SPH. Applied Mechanics and Materials, 275, 393–397.CrossRefGoogle Scholar
  54. Henry JR, Bailey FC, 1970. Slamming of ships: a critical review of the current state of knowledge. Teledyne Materials Research Co., Waltham, MA., USA.Google Scholar
  55. Hermundstad OA, Moan T, 2005. Numerical and experimental analysis of bow flare slamming on a Ro–Ro vessel in regular oblique waves. Journal of Marine Science and Technology, 10, 105–122.CrossRefGoogle Scholar
  56. Hermundstad OA, Moan T, 2009. Efficient methods for direct calculation of slamming loads on ships. Transactions - Society of Naval Architects and Marine Engineers, 117: 156–181.Google Scholar
  57. Hirdaris SE, Temarel P, 2009. Hydroelasticity of ships: recent advances and future trends. Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment, 223(3), 305–330.CrossRefGoogle Scholar
  58. Hosokawa S, Moriyama S, Tomiyama A, Takada N, 2003. PIV measurement of pressure distributions about single bubbles. J Nucl Sci Technol, 40(10): 754–762.CrossRefGoogle Scholar
  59. Howison SD, Ochendon JR, Wilson SK, 1991. Incompressible water-entry problems at small deadrise angles. J. Fluid Mech., 222, 215–230.MathSciNetzbMATHCrossRefGoogle Scholar
  60. Hu ZZ, Greaves D, Raby A, 2016. Numerical wave tank study of extreme waves and wave-structure interaction using OpenFoam®. Ocean Engineering, 126, 329–342.CrossRefGoogle Scholar
  61. Huera-Huarte FJ, Jeon D, Gharib M, 2011. Experimental investigation of water slamming loads on panels. Ocean Engineering, 38(11), 1347–1355.CrossRefGoogle Scholar
  62. Iwanowski B, Fujikubo M, Yao T, 1993. Analysis of horizontal water impact of a rigid body with the air cushion effect. Journal of the Society of Naval Architects of Japan, 293–302.Google Scholar
  63. Jacobsen NG, Fuhrman DR, Fredsøe J, 2012. A wave generation toolbox for the open - source CFD library: OpenFoam®. International Journal for Numerical Methods in Fluids, 70(9), 1073–1088.MathSciNetCrossRefGoogle Scholar
  64. Jalalisendi M, Osma SJ, Porfiri M, 2015. Three-dimensional water entry of a solid body: A particle image velocimetry study. Journal of Fluids and Structures, 59, 85–102.CrossRefGoogle Scholar
  65. Jalalisendi M, Panciroli R, Cha Y, Porfiri M, 2014. A particle image velocimetry study of the flow physics generated by a thin lamina oscillating in a viscous fluid. J. Appl. Phys., 115(5): 054901.CrossRefGoogle Scholar
  66. Jalalisendi M, Shams A, Panciroli R, Porfiri M, 2015. Experimental reconstruction of three-dimensional hydrodynamic loading in water entry problems through particle image velocimetry. Experiments in Fluids, 56(2), 1–17.CrossRefGoogle Scholar
  67. Jensen JJ, 2001. Load and global response of ships. Elsevier Ocean Engineering Book Series, 4, Elsevier, Netherlands.Google Scholar
  68. Judge C, Troesch A, Perlin M, 2004. Initial water impact of a wedge at vertical and oblique angles. Journal of Engineering Mathematics, 48(3/4), 279–303.MathSciNetzbMATHCrossRefGoogle Scholar
  69. Gong Kai, Liu Hua, Wang BL, 2009. Water entry of a wedge based on SPH model with an improved boundary treatment. Journal of Hydrodynamics, Ser. B, 21(6), 750–757.CrossRefGoogle Scholar
  70. Kapsenberg GK, 2011. Slamming of ships: where are we now? Philosophical Transactions of the Royal Society of London A: Mathematical, Physical and Engineering Sciences, 369(1947), 2892–2919.MathSciNetzbMATHCrossRefGoogle Scholar
  71. Kapsenberg GK, van’t Veer AP, Hackett JP, Levadou MMD, 2002. Whipping loads due to aft body slamming. 24th Symposium on Naval Hydrodynamics, Fukuoka, Japan, 25–39.Google Scholar
  72. Kean AJ, Temarel P, Wu XJ, Wu YS, 1991. Hydroelasticity of non-beamlike ships in waves. The Dynamics of Ships. The Royal Soc., London, 153.Google Scholar
  73. Khabakhpasheva TI, 2006. Impact of a surface wave on an elastic hull. Fluid Dynamics, 41(3), 424–433.MathSciNetzbMATHCrossRefGoogle Scholar
  74. Khabakhpasheva TI, Kim Y, Korobkin AA, 2014. Generalised Wagner model of water impact by numerical conformal mapping. Applied Ocean Research, 44, 29–38.CrossRefGoogle Scholar
  75. Khabakhpasheva TI, Korobkin AA, 2013. Elastic wedge impact onto a liquid surface: Wagner’s solution and approximate models. Journal of Fluids and Structures, 36, 32–49.CrossRefGoogle Scholar
  76. Kleefsman KMT, 2005. Water impact loading on offshore structures. Faculty of Mathematics and Natural Sciences, RUG University Groningen, Groningen.Google Scholar
  77. Kihara H, 2004. March. Numerical modeling of flow in water entry of a wedge. Proc. 19th Int. Workshop on Water Waves and Floating Bodies, Cortona, Italy, 28–31.Google Scholar
  78. Koehler JBR, Kettleborough CF, 1977. Hydrodynamic impact of a falling body upon a viscous incompressible fluid. J. Ship Res., 21, 165–181.Google Scholar
  79. Korobkin AA, 1996. Water impact problems in ship hydrodynamics. In: Ohkusu M (ed). Advances in Marine hydrodynamics. Computational Mechanics, Boston, 323–371.Google Scholar
  80. Korobkin AA, 1998. Wave impact on the center of an Euler beam. Journal of Applied Mathematics and Technical Physics, 39(5), 770–781.MathSciNetzbMATHGoogle Scholar
  81. Korobkin AA, 2004. Analytical models of water impact. Euro.Jnl of Applied Mathematics, 15, 821–838.MathSciNetzbMATHCrossRefGoogle Scholar
  82. Korobkin AA, Gueret R, Malenica S, 2006. Hydroelastic coupling of beam finite element model with Wagner theory of water impact. Journal of Fluid and Structures, 22, 493–504.CrossRefGoogle Scholar
  83. Korobkin AA, Malenica S, 2005. Modified Logvinovich model for hydrodynamic loads on asymmetric contours entering water. 20th International Workshop on Water Waves and Floating Bodies, Oslo.Google Scholar
  84. Korobkin AA, Scolan YM, 2006. Three-dimensional theory of water impact. Part 2. Linearized Wagner problem. Journal of Fluid Mechanics, 549, 343–373.MathSciNetCrossRefGoogle Scholar
  85. Kvalsvold J, Faltinsen OM, 1993. Hydroelastic modelling of slamming against the wetdeck of a catamaran. Pro Second Int Conf Fast Sea Transportation, Fast’93, Japan, 681–697.Google Scholar
  86. Kvalsvold J, Faltinsen OM, 1994. Slamming loads on wetdecks of multihull vessels. Pro Second Int Conf Hydroelasticity in Marine Technology, Trondheim, Norway, 205–220.Google Scholar
  87. Kvalsvold J, Faltinsen OM, 1995. Hydroelastic modelling of wetdeck slamming on multihull vessels. J. Ship Res., 39, 225–239.Google Scholar
  88. Kvalsvold J, Faltinsen OM, Aarsnes JV, 1995. Effect of structural elasticity on slamming against wetdecks of multihull vessels. Pro. 6th Int. Symp. Practical Design of Ships and offshore Mobile Units (PRADS), Seoul, South Korea, 1.684-1.699.Google Scholar
  89. Kim K, Shin YS, Wang S, 2008. A stern slamming analysis using three-dimensional CFD simulation. ASME 2008 27th International Conference on Offshore Mechanics and Arctic Engineering. American Society of Mechanical Engineers, 929–934Google Scholar
  90. Lakitosh F, Ananthakrishnan P, 2012. Analysis of ship hull plate vibrations induced by wave and slamming loads. Proc. 31st International Conference on Ocean, Offshore and Arctic Engineering. American Society of Mechanical Engineers, 289–298.Google Scholar
  91. Lewis SG, Hudson DA, Turnock SR, Taunton DJ, 2010. Impact of a free-falling wedge with water: synchronized visualization, pressure and acceleration measurements. Fluid Dynamics Research, 42(3), 035509.zbMATHCrossRefGoogle Scholar
  92. Lind SJ, Stansby PK, Rogers BD, Lloyd PM, 2015. Numerical predictions of water–air wave slam using incompressible–compressible smoothed particle hydrodynamics. Applied Ocean Research, 49, 57–71.CrossRefGoogle Scholar
  93. Lin MC, Ho TY, 1994. Water-entry for a wedge in arbitrary water depth. Engineering Analysis with Boundary Elements, 14(2), 179–185.CrossRefGoogle Scholar
  94. Lin MC, Shieh LD, 1997. Simultaneous measurements of water impact on a two-dimensional body. Fluid Dynamics Research, 19(3), 125–148.CrossRefGoogle Scholar
  95. Liu X, Xu H, Shao S, Lin P, 2013. An improved incompressible SPH model for simulation of wave–structure interaction. Computers & Fluids, 71, 113–123.MathSciNetzbMATHCrossRefGoogle Scholar
  96. Logvinovich GV, 1973. Hydrodynamics of flows with free boundaries. Naukova Dumka, Kyiv, Ukraine.Google Scholar
  97. Lotfollahi-Yaghin MA, Rastgar M, Ahmadi H, 2012. Slamming induced dynamic response of a floating structure. Journal of Marine Science and Technology, 20(2), 201–209.Google Scholar
  98. Lu CH, He YS, Wu GX, 2000. Coupled analysis of nonlinear-interaction between fluid and structure during impact. Journal of Fluid and Structures, 14, 127–146.CrossRefGoogle Scholar
  99. Luo HB, Guedes Soares C, 2012. Review of model tests techniques of local slamming on ships. In: Guedes Soares C, Garbatov Y, Sutulo S, Santos TA (Eds.). Maritime Engineering and Technology, Taylor & Francis, 189–194.CrossRefGoogle Scholar
  100. Luo H, Hu J, Guedes Soares C, 2010. Numerical simulation of hydroelastic responses of flat stiffened panels under slamming loads. ASME 2010 29th International Conference on Ocean, Offshore and Arctic Engineering. American Society of Mechanical Engineers, 373–381.Google Scholar
  101. Luo H, Wang H, Guedes Soares C, 2011a. Comparative study of hydroelastic impact for one free-drop wedge with stiffened panels by experimental and explicit finite element methods. ASME 2011 30th International Conference on Ocean, Offshore and Arctic Engineering. American Society of Mechanical Engineers, 119–127.Google Scholar
  102. Luo HB, Wang S, Guedes Soares C, 2011b. Numerical prediction of slamming loads on a rigid wedge subjected to water entry using an explicit finite element method. In: Guedes Soares C, Fricke W (Eds). Advances in Marine Structures, Taylor & Francis, UK, 41–47.CrossRefGoogle Scholar
  103. Luo H, Wang H, Guedes Soares C, 2012. Numerical and experimental study of hydrodynamic impact and elastic response of one free-drop wedge with stiffened panels. Ocean Engineering, 40, 1–14.CrossRefGoogle Scholar
  104. Luo HB, Zhao Z, Xie P, Wu H, Li X, 2014. Experimental and numerical investigation on hydroelastic impact of one free-drop wedge with aluminum stiffened panels. IEEE OCEANS, Taipei, China, 1–7.Google Scholar
  105. Lv J, Grenestedt JL, 2015. Analytical study of the responses of bottom panels to slamming loads. Ocean Engineering, 94, 116–125.CrossRefGoogle Scholar
  106. Magoga TF, Aksu S, Cannon S, Ojeda R, Thomas G, 2014. Identification of slam events experienced by a high-speed craft. Safety & Reliability of Ships, Offshore & Subsea Structures International Conference, Scotland, UK, 1–13.Google Scholar
  107. Maki KJ, Lee D, Troesch A, Vlahopoulos N, 2011. Hydroelastic impact of a wedge-shaped body. Ocean Engineering, 38, 621–629.CrossRefGoogle Scholar
  108. Marine Accident Investigation Branch (MAIB). 2008 Report on the investigation of the structural failure of MSC Napoli, English Channel on 18 January 2007. MAIB report No. 9/2008. Southampton, UK.Google Scholar
  109. Matsubara S, 2011. Ship motions and wave-induced loads on high speed catamarans. PhD thesis, Australian Maritime College.Google Scholar
  110. Mei XM, Liu YM, Yue DK, 1999. On the water impact of general two-dimensional sections. Applied Ocean Research, 21, 1–15.CrossRefGoogle Scholar
  111. Molin B, Korobkin AA, 2001. Water entry of a perforated wedge. Proc. 16th Int. workshop on water waves and floating bodies, Japan, 121–124Google Scholar
  112. Molteni D, Colagrossi A, Colicchio G, 2007. On the use of an alternative water state equation in SPH. Proc. SPHERIC, 2nd International Workshop, Universidad Politécnica de Madrid, Spain.Google Scholar
  113. Monaghan JJ, 1988. An introduction to SPH. Computer Physics Communications, 48(1), 89–96.zbMATHCrossRefGoogle Scholar
  114. Monaghan JJ, 1992. Smoothed particle hydrodynamics. Annual Review of Astronomy and Astrophysics, 30, 543–574.CrossRefGoogle Scholar
  115. Mousaviraad SM, Wang Z, Stern F, 2015. URANS studies of hydrodynamic performance and slamming loads on high-speed planning hulls in calm water and waves for deep and shallow conditions. Applied Ocean Research, 51, 222–240.CrossRefGoogle Scholar
  116. Murai Y, Nakada T, Suzuki T, Yamamoto F, 2007. Particle tracking velocimetry applied to estimate the pressure field around a savonius turbine. Measurement Science and Technology, 18(8), 2491–2503.CrossRefGoogle Scholar
  117. Nila A, Vanlanduit S, Vepa S, Van Paepegem W, 2013. A PIV-based method for estimating slamming loads during water entry of rigid bodies. Measurement Science and Technology, 24(4), 436–475.CrossRefGoogle Scholar
  118. Oberhagemann J, el Moctar O, 2011, Numerical and experimental investigations of whipping and springing of ship structures. In: The Twenty-first International Offshore and Polar Engineering Conference. International Society of Offshore and Polar Engineers.Google Scholar
  119. Oberhagemann J, Holtmann M, el Moctar O, Schellin TE, Kim D, 2009. Stern slamming of a LNG carrier. Journal of Offshore Mechanics and Arctic Engineering, 131, 013303–1.CrossRefGoogle Scholar
  120. Oberhagemann J, el Moctar O, Holtmann M, Schellin T, Bertram V, Kim DW, 2010. Hydro-elastic simulation of stern slamming and whipping. The International Journal of Ocean and Climate Systems, 1(3/4), 179–188.CrossRefGoogle Scholar
  121. Ochi MK, 1964a. Prediction of occurrence and severity of ship slamming at sea. 5 th Symp. Naval Hydrodynamics, Bergen.Google Scholar
  122. Ochi MK, 1964b. Extreme behavior of a ship in rough seas: Slamming and shipping of green water. SNAME Annual Meeting, New York.Google Scholar
  123. Ochi MK, Motter LE, 1973. Prediction of slamming characteristics and hull response for ship design. Transactions SNAME, 81, 144–190.Google Scholar
  124. Oger G, Doring M, Alessandrini B, Ferrant P, 2006. Two-dimensional SPH simulations of wedge water entries. Journal of Computational Physics, 213(2), 803–822.MathSciNetzbMATHCrossRefGoogle Scholar
  125. Ogilvie TF, 1963. Compressibility effects in ship slamming. Schiffstechnik, 10, 147–154.Google Scholar
  126. Panciroli R, 2013. Water entry of flexible wedges: some issues on the FSI phenomena. Applied Ocean Research, 39, 72–74.CrossRefGoogle Scholar
  127. Panciroli R, Abrate S, Minak G, Zucchelli A, 2012. Hydroelasticity in water-entry problems: Comparison between experimental and SPH results. Composite Structures, 94(2), 532–539CrossRefGoogle Scholar
  128. Panciroli R, Porfiri M, 2013. Evaluation of the pressure field on a rigid body entering a quiescent fluid through particle image velocimetry. Experiments in Fluids, 54(12), 1–13.CrossRefGoogle Scholar
  129. Panciroli R, Porfiri M, 2015. Analysis of hydroelastic slamming through particle image velocimetry. Journal of Sound and Vibration, 347, 63–78.CrossRefGoogle Scholar
  130. Panciroli R, Shams A, Porfiri M, 2015a. Experiments on the water entry of curved wedges: high speed imaging and particle image velocimetry. Ocean Engineering, 94, 213–222.CrossRefGoogle Scholar
  131. Panciroli R, Ubertini S, Minak G, Jannelli E, 2015b. Experiments on the dynamics of flexible cylindrical shells impacting on a water surface. Experimental Mechanics, 55(8), 1537–1550.CrossRefGoogle Scholar
  132. Paik Kwang-jun, Carrica PM, Lee D, Maki K, 2009. Strongly coupled fluid-structure interaction method for structural loads on surface ships. Ocean Engineering, 36, 1346–1357.CrossRefGoogle Scholar
  133. Peseux B, Gornet L, Donguy B, 2005. Hydrodynamic impact: numerical and experimental investigations. J. Fluids Struct., 21(3), 277–303.CrossRefGoogle Scholar
  134. Phan TS, Temarel P, 2002. Hydroelastic responses of pontoon and semi-submersible types of very large floating structure in regular head waves. Proceedings of the International Conference on Offshore Mechanics and Arctic Engineering, paper OMAE2002-28149, 753–763.Google Scholar
  135. Price WG, Wu YS, 1985. Structural responses of a SWATH of multi-hulled vessel traveling in waves. International Conference on SWATH ships and advanced multi-hulled vessels. Royal Institution of Naval Architects, London.Google Scholar
  136. Psaraftis HN, 1978. Some new aspects of slamming probability theory. Journal of Ship Research, 22(3), 186–192.Google Scholar
  137. Qin H, Zhao L, Shen J, 2011. A modified Logvinovich model for hydrodynamic loads on an asymmetric wedge entering water with a roll motion. Journal of Marine Science and Application, 10(2), 184–189.CrossRefGoogle Scholar
  138. Qin Z, Batra RC, 2009. Local slamming impact of sandwich composite hulls. International Journal of Solids and Structures, 46(10), 2011–2035.zbMATHCrossRefGoogle Scholar
  139. Rajendran S, Fonseca N, Guedes Soares C, 2015. Simplified body nonlinear time domain calculation of vertical ship motions and wave loads in large amplitude waves. Ocean Engineering, 107: 157–177.CrossRefGoogle Scholar
  140. Rajendran S, Fonseca N, Guedes Soares C, 2016. Body nonlinear time domain calculation of vertical ship responses in extreme seas accounting for 2nd order Froude-Krylov pressure. Applied Ocean Research, 54: 39–52.CrossRefGoogle Scholar
  141. Ramos J, Incecik A, Guedes Soares C, 2000. Experimental study of slam-induced stresses in a container ship. Mar. Struct., 13(1), 25–52.CrossRefGoogle Scholar
  142. Santoro N, Begovic E, Bertorello C, Bove A, De Rosa S, Franco F, 2014. Experimental study of the hydrodynamic loads on high speed planning craft. Procedia Engineering, 88, 186–193.CrossRefGoogle Scholar
  143. Santos FM, Casetta L, Pesce CP, 2013. Application of a variational method to the vertical hydrodynamic impact of axisymmetric bodies. Applied Ocean Research, 39, 75–82.CrossRefGoogle Scholar
  144. Santos FM, Temarel PA, Guedes Soares C, 2009. On the limitations of two and three-dimensional linear hydroelasticity analyses applied to a fast patrol boat. Journal of Engineering for the Maritime Environment, 223(3), 457–478.Google Scholar
  145. Santos FM, Temarel P, Guedes Soares C, 2009. Modal analysis of a fast patrol boat made of composite material. Ocean Engineering, 36(2), 179–192.CrossRefGoogle Scholar
  146. Savander BR, Scorpio SM, Taylor RK, 2002. Steady hydrodynamic analysis of planing surfaces. Ship Res., 46, 248–279.Google Scholar
  147. Schellin TE, el Moctar O, 2007. Numerical prediction of impact-related wave loads on ships. Journal of Offshore Mechanics and Arctic Engineering, 129(1), 39–47.CrossRefGoogle Scholar
  148. Schiffman M, Spencer DC, 1951. The force of impact on a cone striking a water surface vertical entry. Comm. Pure Appl. Math., 4, 379–417.MathSciNetzbMATHCrossRefGoogle Scholar
  149. Scolan YM, 2004. Hydroelastic behaviour of a conical shell impacting on a quiescent-free surface of an incompressible liquid. Journal of Sound and Vibration, 277(1/2), 163–203.CrossRefGoogle Scholar
  150. Scolan YM, Korobkin AA, 2001. Three-dimensional theory of water impact. Part 1. Inverse Wagner problem. Journal of Fluid Mechanics, 440, 293–326.MathSciNetzbMATHCrossRefGoogle Scholar
  151. Seng S, Jensen JJ, Malenica Š, 2014. Global hydroelastic model for springing and whipping based on a free-surface CFD code (OpenFOAM). International Journal of Naval Architecture and Ocean Engineering, 6(4), 1024–1040.CrossRefGoogle Scholar
  152. Senjanovic I, Catipovic I, Tomasevic S, 2007. Coupled flexural and torsional vibrations of ship-like girders. Thin-Walled Structures, 45, 1002–1021.CrossRefGoogle Scholar
  153. Senjanovic I, Malenica S, Tomasevic S, 2008. Investigation of ship hydroelasticity. Ocean Engineering, 35, 523–535.CrossRefGoogle Scholar
  154. Senjanovic I, Parunov J, 2001. Slamming and whipping analysis of large container ship. Proceedings of the Eleventh, International Offshore and Polar Engineering Conference, Stavanger, Norway, 17–22.Google Scholar
  155. Shams A, Jalalisendi M, Porfiri M, 2015. Experiments on the water entry of asymmetric wedges using particle image velocimetry. Physics of Fluids, 27(2), 027103.CrossRefGoogle Scholar
  156. Shams A, Porfiri M, 2015. Treatment of hydroelastic impact of flexible wedges. Journal of Fluids and Structures, 57, 229–246.CrossRefGoogle Scholar
  157. Shao S, 2009. Incompressible SPH simulation of water entry of a free-falling object. International Journal for Numerical Methods in Fluids, 59(1), 91–115.MathSciNetzbMATHCrossRefGoogle Scholar
  158. Souli M, Ouahsine A, Lewin L, 2000. ALE formulation for fluid-structure interaction problems. Computer Methods in Applied Mechanics and Engineering, 190(5), 659–675.zbMATHCrossRefGoogle Scholar
  159. Southall NR, Lee Y, Johnson MC, Hirdaris SE, White NJ, 2014. Towards a pragmatic method for prediction of whipping: wedge impact simulations using OpenFOAM. Proceedings of the 24th International Offshore and Polar Engineering Conference, Busan, Korea.Google Scholar
  160. Stavovy AB, Chuang SL, 1976. Analytical determination of slamming pressures for high speed vessels in waves. Journal of Ship Research, 20, 190–198.Google Scholar
  161. Stenius I, Rosn A, Kuttenkeuler J, 2006. Explicit FE-modeling of fluid-structure interaction in hull-water impacts. Int. Shipbuild. Prog., 53, 1031–1121.Google Scholar
  162. Stenius I, Rosén A, Battley M, Allen T, 2013. Experimental hydroelastic characterization of slamming loaded marine panels. Ocean Engineering, 74, 1–15.CrossRefGoogle Scholar
  163. Stenius I, Rosn A, Kuttenkeuler J, 2007. Explicit FE-modelling of hydroelasticity in panel-water impacts. Int. Shipbuilding Progr., 54 (2/3), 111–127.Google Scholar
  164. Stenius I, Rosn A, Kuttenkeuler J, 2011. Hydroelastic interaction in panel-water impacts of high-speed craft. Ocean Engineering, 38, 371–381.CrossRefGoogle Scholar
  165. Sun H, 2007. A boundary element method applied to strongly nonlinear wave-body interaction problems. Ph.D. thesis, Norwegian University of Science and Technology, Trondheim, Norway.Google Scholar
  166. Sun H, Faltinsen OM, 2009. Water entry of a bow flare section with a roll angle. J. Mar. Sci. Technol., 14, 69–79.zbMATHCrossRefGoogle Scholar
  167. Sun H, Faltinsen OM, 2006. Water impact of horizontal circular cylinders and cylindrical shells. Applied Ocean Research, 28(5), 299–311.CrossRefGoogle Scholar
  168. Swidan A, Amin W, Ranmuthugala D, Thomas G, Penesis I, 2013. Numerical prediction of symmetric water impact loads on wedge shaped hull form using CFD. World Journal of Mechanics, 3(08), 311.CrossRefGoogle Scholar
  169. Swidan A, Thomas G, Ranmuthugala D, Amin W, Penesis I, Allen T, Battley M, 2016. Experimental drop test investigation into wetdeck slamming loads on a generic catamaran hullform. Ocean Engineering, 117, 143–153.CrossRefGoogle Scholar
  170. Swidan A, Thomas G, Penesis I, Ranmuthugala D, Amin W, Allen T, Battley M, 2017. Wetdeck slamming loads on a developed catamaran hull form–experimental investigation. Ships and Offshore Structures, 12(5), 653–661.CrossRefGoogle Scholar
  171. Tenzer M, Moctar OE, Schellin TE, 2015. Experimental investigation of impact loads during water entry. Ship Technology Research, 62(1), 47–59.CrossRefGoogle Scholar
  172. Thomas G, Winkler S, Davis M, 2011. Slam events of high-speed catamarans in irregular waves. J. Mar. Sci. Technol., 2011, 16, 8–21.CrossRefGoogle Scholar
  173. Tick LJ, 1958. Certain probabilities associated with bow submergence and ship slamming in irregular seas. Journal of Ship Research, 2, 30–36.Google Scholar
  174. Tulin MP, 1957. The theory of slender surfaces planing at high speeds. Schiffstechnik, 4, 125–133.Google Scholar
  175. Tuitman JT, 2010. Hydro-elastic response of ship structures to slamming induced whipping. Ph.D thesis, Delft University of Technology, Delft.Google Scholar
  176. Tveitnes T, Fairlie-Clarke AC, Varyani K, 2008. An experimental investigation into the constant velocity water entry of wedge-shaped sections. Ocean Engineering, 35(14), 1463–1478.CrossRefGoogle Scholar
  177. Van Nuffel D, 2014. Experimental study of the slamming induced pressures, forces and deformations of quasi-rigid and deformable bodies during vertical water entry. Ph.D thesis, Ghent University, Ghent.Google Scholar
  178. Van Nuffel D, Vepa KS, De Baere I, Lava P, Kersemans M, Degrieck J, De Rouck J, Van Paepegem W, 2014. A comparison between the experimental and theoretical impact pressures acting on a horizontal quasi-rigid cylinder during vertical water entry. Ocean Engineering, 77, 42–54.CrossRefGoogle Scholar
  179. Veen DJ, Gourlay TP, 2011. A 2D smoothed particle hydrodynamics theory for calculating slamming loads on ship hull sections. Royal Institution of Naval Architects. Proceedings of the Innovation in High Speed Marine Vessels, Fremantle.Google Scholar
  180. Veen DJ, Gourlay TP, 2012. A combined strip theory and smoothed particle hydrodynamics approach for estimating slamming loads on a ship in headseas. Ocean Engineering, 43, 64–71.CrossRefGoogle Scholar
  181. Verhagen JHG, 1967. The impact of a flat plate on a water surface. Journal of Ship Research, 12, 211–223.Google Scholar
  182. Von Kármàn T, 1929. The impact on seaplane floats during landing. National Advisory Committee for Aeronautics, Technical Note No. 321, 309–313.Google Scholar
  183. Vorus WS, 1996. A flat cylinder theory for vessel impact and steady planing resistance. Journal of Ship Research, 40(2), 89–106.Google Scholar
  184. Wagner H, 1932. Uber Stossund Gleitvergange an der Oberflache von Flussigkeiten. Zeitschrift fuer Angewandte Mathematik und Mechanik, 12, 193–215.CrossRefGoogle Scholar
  185. Wang J, Faltinsen OM, 2013. Numerical investigation of air cavity formation during the high-speed vertical water entry of wedges. Journal of Offshore Mechanics and Arctic Engineering, 135(1), 011101.CrossRefGoogle Scholar
  186. Wang J, Lugni C, Faltinsen OM, 2015a. Experimental and numerical investigation of a freefall wedge vertically entering the water surface. Applied Ocean Research, 51, 181–203.CrossRefGoogle Scholar
  187. Wang J, Lugni C, Faltinsen OM, 2015b. Analysis of loads, motions and cavity dynamics during freefall wedges vertically entering the water surface. Applied Ocean Research, 51, 38–53.CrossRefGoogle Scholar
  188. Wang S, 2016. Hydroelastic response of ship structural components subjected to slamming loads. PhD Thesis, Centre for Marine Technology and Ocean Engineering (CENTEC), Instituto Superior Técnico, Universidade de Lisboa, Lisboa, 201–207.Google Scholar
  189. Wang S, Guedes Soares C, 2012. Water impact of symmetric wedges with a multi-material Eulerian formulation. International Journal of Maritime Engineering, 154 (A4), 191–206.Google Scholar
  190. Wang S, Guedes Soares C, 2013. Slam induced loads on bow-flared sections with various roll angles. Ocean Engineering, 67, 45–57.CrossRefGoogle Scholar
  191. Wang S, Guedes Soares C, 2014a. Asymmetrical water impact of two-dimensional wedges with roll angle. International Journal of Maritime Engineering, 156(A2), 115–130.Google Scholar
  192. Wang S, Guedes Soares C, 2014b. Numerical study on the water impact of 3D bodies by explicit finite element method. Ocean Engineering, 78, 73–88.CrossRefGoogle Scholar
  193. Wang S, Guedes Soares C, 2014c. Comparison of simplified approaches and numerical tools to predict the loads on bottom slamming of marine. In: Guedes Soares, C., López Peña F. (Eds.). Developments in Maritime Transportation and Exploitation of Sea Resources, Francis & Taylor Group, London, UK, 157–170.Google Scholar
  194. Wang S, Guedes Soares C, 2014d. Numerical study on hydroelastic water entry of a wedge. In: Guedes Soares C, López Peña F (Eds.). Developments in Maritime Transportation and Exploitation of Sea Resources, Francis & Taylor Group, London, UK, 199–208.Google Scholar
  195. Wang S, Guedes Soares C, 2015. Experimental and numerical study on bottom slamming probability of a chemical tanker subjected to irregular waves. In: Guedes Soares C, Santos TA (Eds.). Maritime Technology and Engineering, Taylor & Francis Group, London, UK, 1065–1072.Google Scholar
  196. Wang S, Guedes Soares C, 2016a. Experimental and numerical study of the slamming load on the bow of a chemical tanker in irregular waves. Ocean Engineering, 111, 369–383.CrossRefGoogle Scholar
  197. Wang S, Guedes Soares C, 2016b. Stern slamming of a chemical tanker in irregular seas. Ocean Engineering, 122, 322–332.CrossRefGoogle Scholar
  198. Wang S, Guedes Soares C, 2016c. Hydroelastic vibration of bottom platting subjected to wave impact. In: Guedes Soares C, Santos TA (Eds). Maritime Engineering and Technology 3, Taylor and Francis, 1, 401–407.CrossRefGoogle Scholar
  199. Wang S, Karmakar D, Guedes Soares C, 2015. Hydroelastic impact due to longitudinal compression on transient vibration of a horizontal elastic plate. Guedes Soares C, Santos TA (Eds.). Maritime Technology and Engineering, London, UK, 1073–1080.Google Scholar
  200. Wang S, Karmakar D, Guedes Soares C, 2016. Hydroelastic impact of a horizontal floating plate with forward speed. Journal of Fluids and Structures, 60, 97–113.CrossRefGoogle Scholar
  201. Wang S, Luo HB, Guedes Soares C, 2012. Explicit FE simulation of slamming load on rigid wedge with various deadrise angles during water entry. Guedes Soares C, et al. (Eds). Maritime Technology and Engineering, Taylor & Francis, UK, 399–406.CrossRefGoogle Scholar
  202. Wang S, Luo HB, Guedes Soares C, 2014. Numerical prediction of slamming loads on a bow-flared section during water entry. International Journal of Maritime Engineering, 156, A303–A314.Google Scholar
  203. Wang S, Zhang HD, Guedes Soares C, 2016. Slamming occurrence for a chemical tanker advancing in extreme waves. Ocean Engineering, 119, 135–142.CrossRefGoogle Scholar
  204. Wang Yiwen, Wu Weiguo, Guedes Soares C, 2016. Slam induced loads on a 3D bow with various pitch angles. American Society of Mechanical Engineers. ASME 2016 35th International Conference on Ocean, Offshore and Arctic Engineering, V007T06A061-V007T06A061.Google Scholar
  205. Wei Z, Hu C, 2015. Experimental study on water entry of circular cylinders with inclined angles. Journal of Marine Science and Technology, 20(4), 722–738.CrossRefGoogle Scholar
  206. Wu G, 2012. Numerical simulation for water entry of a wedge at varying speed by a high order boundary element method. Journal of Marine Science and Application, 11(2), 143–149.CrossRefGoogle Scholar
  207. Wu GX, Sun H, He YS, 2004. Numerical simulation and experimental study of water entry of a wedge in free fall motion. Journal of Fluids and Structures, 19(3), 277–289.CrossRefGoogle Scholar
  208. Xiao J, Batra R, 2016. Local water slamming of curved rigid hulls. Multiphysics, 6(3), 305–339.CrossRefGoogle Scholar
  209. Xu GD, Duan WY, 2009. Review of prediction techniques on hydrodynamic impact of ships. Journal of Marine Science and Application, 8(3), 204–210.CrossRefGoogle Scholar
  210. Xu GD, Duan WY, Wu GX, 2008. Numerical simulation of oblique water entry of an asymmetrical wedge. Ocean Engineering, 35, 1597–1603.CrossRefGoogle Scholar
  211. Xu GD, Duan WY, Wu GX, 2011. Numerical simulation of water entry of a cone in free-fall motion. The Quarterly Journal of Mechanics and Applied Mathematics, 64(3), 265–285.MathSciNetzbMATHCrossRefGoogle Scholar
  212. Xu L, Troesch AW, Peterson R, 1999. Asymmetric hydrodynamic impact and dynamic response of vessels. Journal of Offshore Mechanics and Arctic Engineering, 121(2), 83–89.CrossRefGoogle Scholar
  213. Xu L, Troesch AW, Vorus WS, 1998. Asymmetric vessel impact and planning hydrodynamics. Ship Res., 42, 187–198.Google Scholar
  214. Yamamoto Y, Ohtsubo H, Okada S, Sawada M, Murakami T, 1983. Cushioning action for horizontal water impact of a flat plate. Journal of the Society of Naval Architects of Japan, 235–242.Google Scholar
  215. Yettou EM, Desrochers A, Champoux Y, 2006. Experimental study on the water impact of a symmetrical wedge. Fluid Dynamics Research, 38(1), 47–66.zbMATHCrossRefGoogle Scholar
  216. Yettou EM, Desrochers A, Champoux Y, 2007. A new analytical model for pressure estimation of symmetrical water impact of a rigid wedge at variable velocities. Journal of Fluids and Structures, 23(3), 501–522.CrossRefGoogle Scholar
  217. Zarnick EE, Hong YS, 1986. Relative bow motion and frequency of slamming of SWATH cross-structure. Report No. DTNSRDC/spd-1174–01. David W Taylor Naval Ship Research and Development Center, Bethesda, MD.Google Scholar
  218. Zhang HD, Cherneva Z, Guedes Soares C, Onorato M, 2014a. Modeling extreme wave heights from laboratory experiments with the nonlinear Schrödinger equation. Nat. Hazards Earth Syst. Sci., 14, 959–968.CrossRefGoogle Scholar
  219. Zhang HD, Guedes Soares C, Onorato M, 2014b. Modelling of the spatial evolution of extreme laboratory wave heights with the nonlinear Schrödinger and Dysthe equations. Ocean Engineering, 89, 1–9.CrossRefGoogle Scholar
  220. Zhang HD, Guedes Soares C, Onorato M, 2015. Modelling of the spatial evolution of extreme laboratory wave crest and trough heights with the NLS-Type equations. Applied Ocean Research, 52, 140–150.CrossRefGoogle Scholar
  221. Zhang HD, Guedes Soares C, Onorato M, Toffoli A, 2016. Modelling of the temporal and spatial evolutions of weakly nonlinear random directional waves with the modified nonlinear Schrödinger equations. Applied Ocean Research, 55, 130–140.CrossRefGoogle Scholar
  222. Zhao R, Faltinsen OM, 1993. Water entry of two-dimensional bodies. J. Fluid Mech., 246, 593–612.zbMATHCrossRefGoogle Scholar
  223. Zhao R, Faltinsen OM, Aarsnes JV, 1996. Water entry of arbitrary two-dimensional sections with and without flow separation. Proceedings of the 21st Symposium on Naval Hydrodynamics, 408–423.Google Scholar
  224. Zhao Y, Chen HC, Yu X, 2015. Numerical simulation of wave slamming on 3D offshore platform deck using a coupled Level-Set and Volume-of-Fluid method for overset grid system. Ocean Systems Engineering, 5(4), 245–259.CrossRefGoogle Scholar

Copyright information

© Harbin Engineering University and Springer-Verlag GmbH Germany 2017

Authors and Affiliations

  1. 1.Centre for Marine Technology and Ocean Engineering (CENTEC), Instituto Superior TécnicoUniversidade de LisboaLisboaPortugal

Personalised recommendations