Advertisement

Journal of Failure Analysis and Prevention

, Volume 19, Issue 2, pp 561–569 | Cite as

Buckling Failure Analysis of Hydraulic Cylinder Rod on the Flap Institutions for Power Catwalk

  • Qiaolei SunEmail author
  • Zheng Chen
  • Liangliang Ding
  • Ding Feng
  • Zhe Wang
  • Yiliu Tu
Technical Article---Peer-Reviewed
  • 61 Downloads

Abstract

This paper analyzes the mechanical characteristics of the hydraulic cylinder rod and the causes of buckling failure. The structural buckling failure often happens to the hydraulic cylinder rod on the flap institutions during the power catwalk operation. The calculation formula of the buckling critical force of the hydraulic cylinder rod is derived by applying the modified boundary conditions. The formula of moment of inertia of different cross sections is deduced, and the calculation formula of the critical force of the hydraulic cylinder rod with defects is obtained by doing research on the rod with the cylindrical defects. Experiments on buckling of hydraulic cylinder rod were conducted on the basis of the simplified test specimen, and the buckling numerical simulation of rod was carried out by using the finite element software Workbench. Through the numerical simulation, we analyze how the radius, depth, and position of the defect to impact the buckling load. The experimental and simulation results show that the formula is accurate when calculating the buckling load of the defect-free hydraulic cylinder rod, and the variation of the buckling load with the cylinder defect parameters was also analyzed.

Keywords

Hydraulic cylinder rod Cylindrical defect Buckling load Experimental study Numerical simulation 

Notes

Acknowledgments

This work was supported by the National Science and Technology Major Project of China under Grant No. 2016ZX05038-002-LH001, the National Natural Science Foundation of China under Grant Nos. 51275057 and 51704034. We would also like to thank SJ Petroleum Machinery Co. of SINOPEC, who is the industrial sponsor to support the project and the relevant experiments.

References

  1. 1.
    B. Levett, Maximizing rig automation safety and efficiency with remote monitoring (SPE 84169), in SPE Annual Technical Conference and Exhibition Held in Denver, Colorado, USA, vol. 10, pp. 75–81 (2003)Google Scholar
  2. 2.
    Q.L. Sun, Design and Theoretical Research on Drilling string Conveying Equipment (Yangtze University, Jingzhou, 2016)Google Scholar
  3. 3.
    D. Hannegan, K. Gray, Real-time data form closed-loop drilling enhances offshore HSE. World Oil 233(3), 33–42 (2013)Google Scholar
  4. 4.
    A. Majeed, L.K. Faisa, Development of an integrated tool for risk analysis of drilling operations. Process Saf. Environ. Prot. 102(07), 421–430 (2016)Google Scholar
  5. 5.
    B. Han, H.Y. Liu, X.P. Shui, Mechanics of Materials, vol. 36 (The Publishing House of Ordnance Industry, Beijing, 2009), pp. 416–458Google Scholar
  6. 6.
    F. Zhou, Z.P. Chen, C.C. Zheng et al., Experimental and numerical buckling failure analysis of acrylic hemispheres for application in neutrino detector. Eng. Fail. Anal. 78, 147–160 (2017)CrossRefGoogle Scholar
  7. 7.
    F. Romano, F. Di Caprio, B. Auriemma et al., Numerical investigation on the failure phenomena of stiffened composite panels in post-buckling regime with discrete damages. Eng. Fail. Anal. 56, 116–130 (2015)CrossRefGoogle Scholar
  8. 8.
    W.Donald White, Comprehensive stability design of planar steel members and framing systems via inelastic buckling analysis. Int. J. Steel Struct. 16(4), 1029–1042 (2016)CrossRefGoogle Scholar
  9. 9.
    Evaldas Narvydas, Buckling strength of hydraulic cylinders—an engineering approach and finite element analysis. Mechanika 22(6), 474–477 (2016)Google Scholar
  10. 10.
    M.S. Ismail, J. Purbolaksono, A. Andriyana et al., The use of initial imperfection approach in design process and buckling failure evaluation of axially compressed composite cylindrical shells. Eng. Fail. Anal. 51, 20–28 (2015)CrossRefGoogle Scholar
  11. 11.
    S.Nika Astapov, Buckling analysis of an elastic rod using the Bubnov–Galerkin method. J. Appl. Mech. Tech. Phys. 49(1), 122–128 (2008)CrossRefGoogle Scholar
  12. 12.
    P.J.G. Montero, E. Salazar, R. Castilla et al., Misalignment effects on the load capacity of a hydraulic cylinder. Int. J. Mech. Sci. 51(2), 105–113 (2009)CrossRefGoogle Scholar
  13. 13.
    M.M. Kashani, A.J. Crewe, N.A. Alexander, Nonlinear cyclic response of corrosion-damaged reinforcing rods with the effect of buckling. Constr. Build. Mater. 41, 388–400 (2003)CrossRefGoogle Scholar
  14. 14.
    J.H. Ge, W. Li, G.M. Chen et al., Experimental and numerical investigation on buckling and post-buckling of a 3000 m Subsea Separator. Eng. Fail. Anal. 74, 107–118 (2017)CrossRefGoogle Scholar
  15. 15.
    Y. Zhang, General equation and its applications for the analysis of stability of the rods. J. South China Univ. Technol. (Nat. Sci.) S1, 116–118 (2003)Google Scholar
  16. 16.
    X. Wang, H.J. Yi, R.X. Zhao et al., Research on stability analysis method of n-order variable cross-section compression rods. China Mech. Eng. 25(13), 1744–1747 (2014)Google Scholar
  17. 17.
    W.G. Huang, C. Li, Z.K. Zhu, On the stability and axial vibration of compressive rods based on nonlocal elasticity theory. J. Vib. Shock 32(05), 154–156 (2013)Google Scholar
  18. 18.
    Y. Ding, J.G. Ge, Z.X. Li, Analysis on ultimate bearing capacity of reticulated shell considering cumulative damage and instability of member. Eng. Mech. 29(5), 13–18 (2012)Google Scholar
  19. 19.
    S.H. Park, J.S. Kim, J.H. Park et al., Molecular dynamics study on size-dependent elastic of silicon nanocantilevers. Thin Solid Films 492(1), 285–289 (2005)CrossRefGoogle Scholar
  20. 20.
    K.Z. Huang, X.L. Chen, Calculating stability of long column while considering axial uniform load. Mech. Eng. 37(6), 744–749 (2015)Google Scholar
  21. 21.
    F. Fan, J. Yan, Z. Cao, Stability of reticulated shells considering member buckling. J. Constr. Steel Res. 77, 32–42 (2012)CrossRefGoogle Scholar
  22. 22.
    X.B. Liu, M.S. Cui, C.W. Zhang, Calculation and analysis on bending stability of roof support hydraulic cylinder piston. Coal Mine Mach. 29(01), 67–70 (2008)Google Scholar
  23. 23.
    Y.B. Kim, P.Y. Kim, I.K. Kim, A study on the durability design of a hydraulic cylinder for an excavator. Trans. Korean Soc. Mech. Eng. 34(12), 1901–1907 (2010)CrossRefGoogle Scholar
  24. 24.
    Y.F. Lu, Y.H. Lin, T. Zhao et al., A theoretical solution to the residual collapsing strength of the oil-well pipe under high-corrosion circumstances. China Pet. Mach. 38(08), 17–20 (2010)Google Scholar
  25. 25.
    Y.Q. Long, S.H. Bao, Structural Mechanics (Higher Education Press, Beijing, 1981)Google Scholar

Copyright information

© ASM International 2019

Authors and Affiliations

  1. 1.School of Mechanical EngineeringYangtze UniversityJingzhouChina
  2. 2.Hubei Engineering Research Center for Oil & Gas Drilling and Completion ToolsJingzhouChina
  3. 3.Hubei Cooperative Innovation Center of Unconventional Oil and GasWuhanChina

Personalised recommendations