Journal of Failure Analysis and Prevention

, Volume 16, Issue 6, pp 1101–1107 | Cite as

Simulation and Experimental Research of PDC Bit Cutting Rock

  • Yuchun Kuang
  • Mingming Zhang
  • Ming Feng
  • Yi Zhang
  • Yiwei Han
  • Yazhou Peng
Technical Article---Peer-Reviewed
  • 241 Downloads

Abstract

In order to achieve efficiently the optimal design and evaluation of PDC (polycrystalline diamond compact) bit, a finite element model for PDC bit cutting rock was established, forecasting the torque and the drilling pressure distribution trends of the cutting teeth on the bit. Through the PDC bit drilling rock, our experimental model validates the reasonableness and effectiveness of finite element simulation. It further demonstrates that the results of the changing trend of experiment and finite element simulation are very close and verify the accuracy and feasibility of the simulation model. The finite element model for single wing PDC cutting rock was established. This paper analyzes the distribution trends of the cutter torque and drilling pressure on bit under the conditions of the different penetration rates and rotational speeds. The “attack” of the cutting teeth is also analyzed. The results show that the torque of the cutting teeth is increased with the increasing penetration rate with the other conditions being the same. Under the same penetration rate and rotating speed, the drilling pressure of the cutting teeth tends to increase first with the increasing distance from the center axis of the drill bit, and then decrease. The cutting force of each tooth increases with the increasing penetration rate, and near the shoulder, it reaches the maximum, even though the cutting force is less affected by the rotating speed.

Keywords

PDC bit Penetration rate The torque Drilling pressure Finite element 

References

  1. 1.
    G. Zhang, Study on rock breaking mechanism and state identification technology of rock PDC [D], China University of Mining and Technology, 2015.Google Scholar
  2. 2.
    M. Zhao, PDC drilling parameters optimization model and Application Research [D], Daqing Petroleum Institute, 2003.Google Scholar
  3. 3.
    X. Zhu, H. Li, Numerical simulation of cutting efficiency of cutting teeth in PDC. J. Appl. Sci. Eng. 01, 182–191 (2015)Google Scholar
  4. 4.
    T. Richard, C. Coudyzer, S. Desmette, Influence of groove geometry and cutter inclination in rock cutting[C]. 44th US Rock Mechanics Symposium and 5th US-Canada Rock Mechanics Symposium, American Rock Mechanics Association, 2010.Google Scholar
  5. 5.
    Y. Zhou, Z. Wang, Study on the effect of cutting angle on the rock breaking effect in the cutting angle of PDC bit cutting. Coal Mine Mach. 08, 49–51 (2009)Google Scholar
  6. 6.
    T.O. Pryhorovska, S.S. Chaplinskiy, I.O. Kudriavtsev, Finite element modelling of rock mass cutting by cutters for PDC drill bits. Pet Explor. Dev. 42(6), 888–892 (2015)CrossRefGoogle Scholar
  7. 7.
    S. Yang, Development of conical PDC teeth and evaluation of laboratory tests for. Pet. Field Mach. 06, 38–42 (2015)Google Scholar
  8. 8.
    G. Hareland, R. Nygaard, W. Yan et al., Cutting efficiency of a single PDC cutter on hard rock. J. Can. Pet. Technol. 48(06), 60–65 (2009)CrossRefGoogle Scholar
  9. 9.
    B. Akbari, S.Z. Miska, M. Yu, et al., The effects of size, Chamfer geometry, and Back Rake angle on frictional response of PDC cutters[C]. 48th US Rock Mechanics/Geomechanics Symposium, American Rock Mechanics Association, 2014.Google Scholar
  10. 10.
    P. Ju, Z. Wang, Y. Zhai et al., Numerical simulation study on the optimization design of the crown shape of PDC drill bit. J. Pet. Explor. Prod. Technol. 4(4), 343–350 (2014)CrossRefGoogle Scholar
  11. 11.
    H. Cai, Optimization of key design parameters of PDC bit [D], China University of Petroleum, 2008.Google Scholar
  12. 12.
    H. Zhu, Q. Liu, J. Deng, The fracture mechanism of rock under the condition of drilling and rotary drilling. J. Appl. Sci. Eng. 04, 622–631 (2012)Google Scholar
  13. 13.
    X. Dong, J. Xiong, G. Wang, Numerical simulation of breaking rock mechanism of oscillation. J. Southwest Pet. Univ. Nat. Sci. Ed. 36(06), 160–167 (2014)Google Scholar
  14. 14.
    Q. Zhang, D. Li, W. Jing, S. Hu, PDC drill bit single tooth “attack” cloth tooth research and finite element analysis. Pet. Mach. 10, 5–8 (2014)Google Scholar

Copyright information

© ASM International 2016

Authors and Affiliations

  • Yuchun Kuang
    • 1
  • Mingming Zhang
    • 1
  • Ming Feng
    • 2
  • Yi Zhang
    • 1
  • Yiwei Han
    • 1
  • Yazhou Peng
    • 3
  1. 1.School of Mechatronic EngineeringSouthwest Petroleum UniversityChengduChina
  2. 2.Sichuan Chuanqing Oil Drilling Technology Co. LtdGuanghanChina
  3. 3.Sichuan Drilling & Production Technology Research Institute of SPAGuanghanChina

Personalised recommendations