Advertisement

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

  • Hui LiEmail author
  • Zhanglong ZhaoEmail author
  • Hongzhen Guo
  • Yongquan Ning
  • Zekun Yao
Article
  • 38 Downloads

Abstract

A dislocation density-based constitutive model that considered the effects of initial lamellar thickness was proposed to predict the flow behavior of a near-α high-temperature Ti-5.4Al-3.7Sn-3.3Zr-0.5Mo-0.4Si alloy. The evolution equations of dislocation density were improved by introducing the influence of the dynamic globularization of lamellar microstructure with different initial thicknesses. The evolution equations and Hall-Petch behavior were coupled into the constitutive model, which was composed of athermal and thermal stresses. According to the established constitutive equations, the variation and contributions of corresponding stress components were analyzed. The calculated dislocation densities were compared with the experimental values obtained by electron backscattered diffraction data to verify the model. Moreover, the flow stresses of the studied alloy with different initial lamellar microstructures under various deformation conditions were predicted. Good agreements between the predicted and experimental results were obtained. Additionally, steady-state flow behavior was further analyzed and the relationship between the calculated steady-state flow stress and the equiaxed α-phase size was quantitatively obtained. The results indicated the validity of the proposed constitutive model for predicting the flow behavior of the alloy with different initial lamellar microstructures over a range of deformation temperatures and strain rates.

Keywords

alpha lamellar thickness dislocation density high-temperature titanium alloy physically based model 

Notes

Acknowledgments

This study was financially supported by the Fundamental Research Funds for the Central Universities (No. 3102016ZY010), the National Natural Science Foundation of Shaanxi Province (No. 2015JQ5152) and the National Natural Science Foundation of China (No. 51205319).

References

  1. 1.
    P. Wanjara, M. Jahazi, H. Monajati, and S. Yue, Influence of Thermomechanical Processing on Microstructural Evolution in Near-α Alloy IMI834, Mater. Sci. Eng., A, 2006, 416(1), p 300–311CrossRefGoogle Scholar
  2. 2.
    J.C. Williams and E.A. Starke, Progress in Structural Materials for Aerospace systems, Acta Mater., 2003, 51(19), p 5775–5799CrossRefGoogle Scholar
  3. 3.
    Y.C. Lin, J. Huang, H.B. Li, and D.D. Chen, Phase Transformation and Constitutive Models of a hOt Compressed TC18 Titanium Alloy in the α + β Regime, Vacuum, 2018, 157, p 83–91CrossRefGoogle Scholar
  4. 4.
    Y.Q. Jiang, Y.C. Lin, X.Y. Zhang, C. Chen, Q.W. Wang, and G.D. Pang, Isothermal Tensile Deformation Behaviors and Fracture Mechanism of Ti-5Al-5Mo-5 V-1Cr-1Fe Alloy in β Phase Field, Vacuum, 2018, 156, p 187–197CrossRefGoogle Scholar
  5. 5.
    D.D. Chen, Y.C. Lin, Y. Zhou, M.S. Chen, and D.X. Wen, Dislocation Substructures Evolution and an Adaptive-Network-Based Fuzzy Inference System Model for Constitutive Behavior of a Ni-Based Superalloy During Hot Deformation, J. Alloy. Compd., 2017, 708, p 938–946CrossRefGoogle Scholar
  6. 6.
    G.Z. Quan, W.Q. Lv, Y.P. Mao, Y.W. Zhang, and J. Zhou, Prediction of Flow Stress in a Wide Temperature Range Involving Phase Transformation for As-Cast Ti-6Al-2Zr-1Mo-1 V Alloy by Artificial Neural Network, Mater. Des., 2013, 50, p 51–61CrossRefGoogle Scholar
  7. 7.
    J.W. Zhao, H. Ding, W.J. Zhao, M.L. Huang, D.B. Wei, and Z.Y. Jiang, Modelling of the Hot Deformation Behaviour of a Titanium Alloy Using Constitutive Equations and Artificial Neural Network, Comput. Mater. Sci., 2014, 92, p 47–56CrossRefGoogle Scholar
  8. 8.
    Y.C. Lin and X.M. Chen, A Critical Review of Experimental Results and Constitutive Descriptions for Metals and Alloys in Hot Working, Mater. Des., 2011, 32(4), p 1733–1759CrossRefGoogle Scholar
  9. 9.
    X.F. Tang, B.Y. Wang, Y.M. Huo, W.Y. Ma, J. Zhou, H.C. Ji, and X.B. Fu, Unified Modeling of Flow Behavior and Microstructure Evolution in Hot Forming of a Ni-Based Superalloy, Mater. Sci. Eng., A, 2016, 662, p 54–64CrossRefGoogle Scholar
  10. 10.
    X.G. Fan and H. Yang, Internal-State-Variable Based Self-consistent Constitutive Modeling for Hot Working of Two-Phase Titanium Alloys Coupling Microstructure Evolution, Int. J. Plast., 2011, 27(11), p 1833–1852CrossRefGoogle Scholar
  11. 11.
    Z.C. Sun, H. Yang, G.J. Han, and X.G. Fan, A Numerical Model Based on Internal-State-Variable Method for the Microstructure Evolution During Hot-Working Process of TA15 Titanium Alloy, Mater. Sci. Eng., A, 2010, 527(15), p 3464–3471CrossRefGoogle Scholar
  12. 12.
    J. Luo, M.Q. Li, X.L. Li, and Y.P. Shi, Constitutive Model for High Temperature Deformation of Titanium Alloys Using Internal State Variables, Mech. Mater., 2010, 42(2), p 157–165CrossRefGoogle Scholar
  13. 13.
    B. Babu and L. Lindgren, Dislocation Density Based Model for Plastic Deformation and Globularization of Ti-6Al-4V, Int. J. Plast., 2013, 50, p 94–108CrossRefGoogle Scholar
  14. 14.
    P.F. Gao, H. Yang, X.G. Fan, and S. Zhu, Unified Modeling of Flow Softening and Globularization for Hot Working of Two-Phase Titanium Alloy with a Lamellar Colony Microstructure, J. Alloy. Compd., 2014, 600, p 78–83CrossRefGoogle Scholar
  15. 15.
    E.B. Shell and S.L. Semiatin, Effect of Initial Microstructure on Plastic Flow and Dynamic Globularization During Hot Working of Ti-6Al-4V, Metall. Mater. Trans. A, 1999, 30(12), p 3219–3229CrossRefGoogle Scholar
  16. 16.
    S.L. Semiatin and T.R. Bieler, The Effect of Alpha Platelet Thickness on Plastic Flow During Hot Working of Ti-6Al-4V with a Transformed Microstructure, Acta Mater., 2001, 49(17), p 3565–3573CrossRefGoogle Scholar
  17. 17.
    Z.L. Zhao, H. Li, M.W. Fu, H.Z. Guo, and Z.K. Yao, Effect of the Initial Microstructure on the Deformation Behavior of Ti60 Titanium Alloy at High Temperature Processing, J. Alloy. Compd., 2014, 617, p 525–533CrossRefGoogle Scholar
  18. 18.
    H. Li, Z.L. Zhao, H.Z. Guo, Z.K. Yao, Y.Q. Ning, X.P. Miao, and M.M. Ge, Effect of Initial Alpha Lamellar Thickness on Deformation Behavior of a Near-α High-Temperature Alloy During Thermomechanical Processing, Mater. Sci. Eng., A, 2017, 682, p 345–353CrossRefGoogle Scholar
  19. 19.
    F. Roters, D. Raabe, and G. Gottstein, Work Hardening in Heterogeneous Alloys-a Microstructural Approach Based on Three Internal State Variables, Acta Mater., 2000, 48(17), p 4181–4189CrossRefGoogle Scholar
  20. 20.
    S. Nemat-Nasser, W. Guo, and D.P. Kihl, Thermomechanical Response of AL-6XN Stainless Steel Over a Wide Range of Strain Rates and Temperatures, J. Mech. Phys. Solids, 2001, 49(8), p 1823–1846CrossRefGoogle Scholar
  21. 21.
    R.C. Picu and A. Majorell, Mechanical Behavior of Ti-6Al-4V at High and Moderate Temperatures-Part II: Constitutive Modeling, Mater. Sci. Eng., A, 2002, 326(2), p 306–316CrossRefGoogle Scholar
  22. 22.
    R. Liu, M. Salahshoor, S.N. Melkote, and T. Marusich, A Unified Internal State Variable Material Model for Inelastic Deformation and Microstructure Evolution in SS304, Mater. Sci. Eng., A, 2014, 594, p 352–363CrossRefGoogle Scholar
  23. 23.
    H. Mecking and U.F. Kocks, Kinetics of Flow and Strain-Hardening, Acta Metall., 1981, 29(11), p 1865–1875CrossRefGoogle Scholar
  24. 24.
    L.E. Lindgren, K. Domkin, and S. Hansson, Dislocations, Vacancies and Solute Diffusion in Physical Based Plasticity Model for AISI, 316L, Mech. Mater., 2008, 40(11), p 907–919CrossRefGoogle Scholar
  25. 25.
    Y. Estrin, L.S. Tóth, A. Molinari, and Y. Bréchet, A Dislocation-Based Model for all Hardening Stages in Large Strain Deformation, Acta Mater., 1998, 46(15), p 5509–5522CrossRefGoogle Scholar
  26. 26.
    V. Bata and E.V. Pereloma, An Alternative Physical Explanation of the Hall-Petch Relation, Acta Mater., 2004, 52(3), p 657–665CrossRefGoogle Scholar
  27. 27.
    S.L. Semiatin and T.R. Bieler, Effect of Texture and Slip Mode on the Anisotropy of Plastic Flow and Flow Softening During Hot Working of Ti-6Al-4V, Metall. Mater. Trans. A, 2001, 32(7), p 1787–1799CrossRefGoogle Scholar
  28. 28.
    I.J. Beyerlein and C.N. Tomé, A Dislocation-Based Constitutive Law for Pure Zr Including Temperature Effects, Int. J. Plast., 2008, 24(5), p 867–895CrossRefGoogle Scholar
  29. 29.
    M. Mulyadi, M.A. Rist, L. Edwards, and J.W. Brooks, Parameter Optimisation in Constitutive Equations for Hot Forging, J. Mater. Process. Technol., 2006, 177(1–3), p 311–314CrossRefGoogle Scholar
  30. 30.
    R.C. Guo and J.J. Wu, Dislocation Density Based Model for Al-Cu-Mg Alloy During Quenching with Considering the Quench-Induced Precipitates, J. Alloy. Compd., 2018, 741, p 432–441CrossRefGoogle Scholar
  31. 31.
    S. Mironov, M. Murzinova, S. Zherebtsov, G.A. Salishchev, and S.L. Semiatin, Microstructure Evolution During Warm Working of Ti-6Al-4V with a Colony-α Microstructure, Acta Mater., 2009, 57(8), p 2470–2481CrossRefGoogle Scholar
  32. 32.
    J. Lin and T.A. Dean, Modelling of Microstructure Evolution in Hot Forming Using Unified Constitutive Equations, J. Mater. Process. Technol., 2005, 167(2–3), p 354–362CrossRefGoogle Scholar
  33. 33.
    M. Zhou and F. Dunne, Mechanisms-Based Constitutive Equations for the Superplastic Behaviour of a Titanium Alloy, J. Strain Anal. Eng. Des., 1996, 31(3), p 187–196CrossRefGoogle Scholar
  34. 34.
    J. Lin, B.H. Cheong, and X. Yao, Universal Multi-Objective Function for Optimising Superplastic-Damage Constitutive Equations, J. Mater. Process. Technol., 2002, 125–126, p 199–205CrossRefGoogle Scholar
  35. 35.
    J. Lin and J.B. Yang, GA-Based Multiple Objective Optimisation for Determining Viscoplastic Constitutive Equations for Superplastic Alloys, Int. J. Plast., 1999, 15(11), p 1181–1196CrossRefGoogle Scholar
  36. 36.
    J. Cao and J. Lin, A Study on Formulation of Objective Functions for Determining Material Models, Int. J. Mech. Sci., 2008, 50(2), p 193–204CrossRefGoogle Scholar
  37. 37.
    L.P. Evers, W.A.M. Brekelmans, and M.G.D. Geers, Non-Local Crystal Plasticity Model with Intrinsic SSD and GND Effects, J. Mech. Phys. Solids, 2004, 52(10), p 2379–2401CrossRefGoogle Scholar
  38. 38.
    A. Ramazani, K. Mukherjee, A. Schwedt, P. Goravanchi, U. Prahl, and W. Bleck, Quantification of the Effect of Transformation-Induced Geometrically Necessary Dislocations on the Flow-Curve Modelling of Dual-Phase Steels, Int. J. Plast., 2013, 43, p 128–152CrossRefGoogle Scholar
  39. 39.
    H. Dini, A. Svoboda, N. Andersson, E. Ghassemali, L. Lindgren, and A.E.W. Jarfors, Optimization and Validation of a Dislocation Density Based Constitutive Model for As-Cast Mg-9%Al-1%Zn, Mater. Sci. Eng., A, 2018, 710, p 17–26CrossRefGoogle Scholar
  40. 40.
    M. Calcagnotto, D. Ponge, E. Demir, and D. Raabe, Orientation Gradients and Geometrically Necessary Dislocations in Ultrafine Grained Dual-Phase Steels Studied by 2D and 3D EBSD, Mater. Sci. Eng., A, 2010, 527(10), p 2738–2746CrossRefGoogle Scholar
  41. 41.
    L. Yang, B.Y. Wang, G. Liu, H.J. Zhao, and W.C. Xiao, Behavior and Modeling of Flow Softening and Ductile Damage Evolution in Hot Forming of TA15 alloy Sheets, Mater. Des., 2015, 85, p 135–148CrossRefGoogle Scholar
  42. 42.
    B. Derby, The Dependence of Grain Size on Stress During Dynamic Recrystallisation, Acta Metall. Mater., 1991, 39(5), p 955–962CrossRefGoogle Scholar
  43. 43.
    S. Gourdet and F. Montheillet, A Model of Continuous Dynamic Recrystallization, Acta Mater., 2003, 51(9), p 2685–2699CrossRefGoogle Scholar
  44. 44.
    A. Pougis, T.S. Toth, J.J. Fundenberger, and A. Borbely, Extension of the Derby Relation to Metals Severely Deformed to Their Steady-State Ultrafine-Grain Size, Scripta Mater., 2014, 72–73, p 59–62CrossRefGoogle Scholar
  45. 45.
    S.A.A. Shams, S. Mirdamadi, S.M. Abbasi, D. Kim, and C.S. Lee, Mechanism of Martensitic to Equiaxed Microstructure Evolution During Hot Deformation of a Near-Alpha Ti Alloy, Metall. Mater. Trans. A, 2017, 48(6), p 2979–2992CrossRefGoogle Scholar

Copyright information

© ASM International 2019

Authors and Affiliations

  1. 1.School of Materials Science and EngineeringNorthwestern Polytechnical UniversityXi’anPeople’s Republic of China

Personalised recommendations