Tribological Performance of Ni3Al Matrix Composites Synthesized by Laser Melt Deposition Under Different Scanning Velocities
- 54 Downloads
In order to study the effect of scanning velocity on the microstructure and tribological properties of Ni3Al matrix composites containing graphene nanoplatelets (NGs), a series of NG samples are successfully synthesized by laser melt deposition under the various scanning velocities from 300 to 500 mm s−1. The sliding friction tests of NG against GCr15 steel balls are carried out under 10 N and 0.2 m s−1 at room temperature. The microstructures, tribological properties and wear mechanisms of the NG samples are analyzed. The results show that the scanning velocity can be optimized to effectively control the surface hardness and relative density, as well as tribological performance of NG. The NG sample synthesized under scanning velocity of 450 mm s−1 has a dense and fine microstructure as well as excellent properties such as higher relative density (98.6%), lower friction coefficient (0.23) and wear rate (5.5 × 10−6 mm3 N−1 m−1). The lower substrate layer with dense and stable structure plays an important role in supporting the upper glaze layer with rich graphene and oxides, as well as nanocrystalline structure, which contributes to the excellent friction-reducing and wear resistance performances of NG. The research results could be used to guide the selection of suitable scanning velocity and study the wear mechanisms of NG for having excellent tribological performance.
Keywordscomposite materials electron microscopy laser melt deposition tribology wear
This work was supported by the National Natural Science Foundation of China (51275370); the Fundamental Research Funds for the Central Universities (2017-YB-019); Self-determined and Innovative Research Funds of WUT (135204008); authors were grateful to M.J. Yang, X.L. Nie, S.L. Zhao, Y.M. Li and W.T. Zhu in Material Research and Test Center of WUT for their kind help with EPMA and FESEM.
- 6.W.Z. Zhai, X.L. Shi, S.Y. Song, J. Yao, A.M.M. Ibrahim, Z.S. Xu, A.Q.U. Din, L. Chen, Q.S. Zhu, Y.C. Xiao, and Q.X. Zhang, Tribological Performance of Ni3Al Self-Lubricating Composites with Different Content of TiC at Elevated Temperature, Tribol. Trans., 2015, 58(2), p 365–373CrossRefGoogle Scholar
- 16.L. Liu, Y.J. Shangguan, H.Z. Li, H.B. Tang, and H.M. Wang, Sliding Wear Behavior of Laser-Nitrided and Thermal Oxidation Treated Ti-5Al-5Mo-5V-1Cr-1Fe Alloy Fabricated by Laser Melting Deposition, Appl. Phys. A Mater., 2016, 122(4), p 1–7Google Scholar
- 18.M.K. Imran, S.H. Masood, and M. Brandt, Influence of process parameters in the direct metal deposition of h13 tool steel on copper alloy substrate, Lecture Notes in Engineering & Computer Science, Proceedings of the world congress on engineering 2010, WCE 2010, June 30–July 2, London, UK, 2010, 2185(1), p 2213–2218Google Scholar
- 23.A. Nieto, A. Bisht, D. Lahiri, C. Zhang, and A. Agarwal, Graphene Reinforced Metal and Ceramic Matrix Composites: A Review, Int. Mater. Rev., 2016, 10, p 241–302Google Scholar
- 27.American Society for Testing and Materials, Standard Test Method for Knoop and Vickers Hardness of Materials, ASTM E384-11 e1, 2012Google Scholar
- 28.American Society for Testing and Materials, Standard Test Methods for Density of Compacted or Sintered Powder Metallurgy (PM) Products using Archimedes’ Principle, ASTM B962-13, 2014Google Scholar