Abstract
Tearing as a factor that restricts formability of sheets and tubes is determined by forming limit diagram (FLD). The aim of the current study is to present a novel approach to achieve FLD of a metallic tube using hydroforming process. Here, for 304 stainless steel tubes, various loading conditions, namely free loading, bulging with axial feeding and bulging with closed end, were considered. Along with loading condition, die geometries with different corner radius and deformation width were studied on the strain path and plastic instability. The effects of process parameters on the strain path have been evaluated and simulated using ABAQUS/Explicit. Meshed tubes were bulged under controlled loading, and the FLD was drawn after measuring the major and minor strains close to the tearing location. Finally, the evaluation of the current method has been investigated by using the obtained FLD in the forming of an industrial part (i.e., the cam-shaped tube). The results revealed that the proposed approach has the capability to predict the formability of industrial components.
Similar content being viewed by others
References
S.P. Keeler and W.A. Backofen, Plastic Instability and Fracture in Sheets Stretched Over Rigid Punches, ASM Trans. Q., 1963, 56(1), p 25–48
G.M. Goodwin, Application of Strain Analysis to Sheet Metal Forming Problems in the Press Shop. 1968, SAE Technical Paper.
T.B. Stoughton and X. Zhu, Review of Theoretical Models of the Strain-Based FLD and Their Relevance to the Stress-Based FLD, Int. J. Plast., 2004, 20(8), p 1463–1486
A. Fatemi and B.M. Dariani, The Effect of Normal and Through Thickness Shear Stresses on the Formability of Isotropic Sheet Metals, J. Braz. Soc. Mech. Sci. Eng., 2016, 38(1), p 119–131
A. Yaghoobi et al., Application of Adaptive Neuro Fuzzy Inference System and Genetic Algorithm for Pressure Path Optimization in Sheet Hydroforming Process, Int. J. Adv. Manuf. Technol., 2016, 86(9), p 2667–2677
B. Ma et al., The Effect of the Through-Thickness Normal Stress on Sheet Formability, J. Manuf. Process., 2016, 21, p 134–140
N. Asnafi and A. Skogsgårdh, Theoretical and Experimental Analysis of Stroke-Controlled Tube Hydroforming, Mater. Sci. Eng. A, 2000, 279(1), p 95–110
N. Asnafi, Analytical Modelling of Tube Hydroforming, Thin-Walled Struct., 1999, 34(4), p 295–330
J. Kim et al., Analytical Approach to Bursting in Tube Hydroforming Using Diffuse Plastic Instability, Int. J. Mech. Sci., 2004, 46(10), p 1535–1547
E. Chu and Y. Xu, Influences of Generalized Loading Parameters on FLD Predictions for Aluminum Tube Hydroforming, J. Mater. Process. Technol., 2008, 196(1), p 1–9
P. Thanakijkasem et al., Comparative Study of Finite Element Analysis in Tube Hydroforming of Stainless Steel 304, Int. J. Autom. Technol., 2015, 16(4), p 611–617
G. Ngaile, S. Jaeger, and T. Altan, Lubrication in Tube Hydroforming (THF): Part I. Lubrication Mechanisms and Development of Model Tests to Evaluate Lubricants and Die Coatings in the Transition and Expansion Zones, J. Mater. Process. Technol., 2004, 146(1), p 108–115
D. Simulia, Abaqus 6.11 Analysis User’s Manual. Abaqus 6.11 Documentation, 2011.
R. Makkouk et al., Experimental and Theoretical Analysis of the Limits to Ductility of Type 304 Stainless Steel Sheet, Eur. J. Mech. A/Solids, 2008, 27(2), p 181–194
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Naghibi, M.F., Gerdooei, M. & Jooybari, M.B. Experimental and Numerical Study on Forming Limit Diagrams of 304 Stainless Steel Tubes in the Hydroforming Process. J. of Materi Eng and Perform 25, 5460–5467 (2016). https://doi.org/10.1007/s11665-016-2382-z
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-016-2382-z