Advertisement

Journal of Thermal Science

, Volume 29, Issue 1, pp 182–193 | Cite as

Heat Transfer and Thermal Characteristics Effects on Moving Plate Impinging from Cu-Water Nanofluid Jet

  • Abanti DattaEmail author
  • Sonal Kumar
  • Pabitra Halder
Article
  • 61 Downloads

Abstract

The present article is focused on modelling of flow and heat transfer behaviour of Cu-water nanofluid in a confined slot jet impingement on hot moving plate. Different parameters such as various moving plate velocities, nanoparticles at various concentrations, variation in turbulent Reynolds number and jet nozzle to plate distance have been considered to study the flow field and convective heat transfer performance of the system. Results of distribution of local and average Nusselt number and skin friction coefficients at the plate surface are shown to elucidate the heat transfer and fluid flow process. Qualitative analysis of both stream function and isotherm contours are carried out to perceive the flow pattern and heat transfer mechanism due to moving plate. The results revealed that average Nusselt number significantly rises with plate velocity in addition with jet inlet Reynolds number. Correlations of the average Nusselt numbers are presented.

Keywords

Cu-water nanofluid multiphase mixture model moving plate jet impingement CFD 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. [1]
    Choi S.U.S., Eastman J.A., Enhancing thermal conductivity of fluids with nanoparticles. American Society of Mechanical Engineers. Fluids Engineering Division (Publication) FED, 1995, pp.: 99–105.Google Scholar
  2. [2]
    Masuda H., Ebata A., Teramae K., Hishinuma N., Alteration of thermal conductivity and viscosity of liquid by dispersing ultra-fine particles (Dispersion of γ — Al2O3, SiO2, and TiO2 Ultra-fine particles.). NetsuBussei, 1993, 7(4): 227–233. (in Japanese)Google Scholar
  3. [3]
    Kilic M., Calisir T., Baskaya S., Experimental and numerical study of heat transfer from a heated flat plate in a rectangular channel with an impinging jet. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2017, 39(1): 329–344.CrossRefGoogle Scholar
  4. [4]
    Kilic M., Calisir T., Baskaya S., Experimental and numerical investigation of vortex promoter effects on heat transfer from heated electronic components in a rectangular channel with an impinging jet. Heat Transfer Research, 2017, 48(5): 435–463.CrossRefGoogle Scholar
  5. [5]
    Sharif M.A.R., Banerjee A., Numerical analysis of heat transfer due to confined slot-jet impingement on a moving plate. Applied Thermal Engineering, 2009, 29(2–3): 532–540.CrossRefGoogle Scholar
  6. [6]
    Roy G., Nguyen C.T., Lajoie P., Numerical investigation of laminar flow and heat transfer in a radial flow cooling system with the use of nanofluids. Super Lattices and Microstructures, 2004, 35(3–6): 497–511.ADSCrossRefGoogle Scholar
  7. [7]
    Manca O., Mesolella P., Nardini S., Ricci D., Numerical study of a confined slot impinging jet with nanofluids. Nanoscale Research Letters, 2011, 6(1): 188.ADSCrossRefGoogle Scholar
  8. [8]
    Kilic M., Muhammad A., Numerical investigation of combined effect of nanofluids and multiple impinging jets on heat transfer. Thermal Science, 2018, doi. https://doi.org/10.2298/TSCI171204094K.Google Scholar
  9. [9]
    Xuan Y.M., Li Q., Investigation on convective heat transfer and flow features of nanofluids. ASME Journal of Heat Transfer 2003, 125(2): 151–155.CrossRefGoogle Scholar
  10. [10]
    Li Q., Xuan Y.M.: Convective heat transfer and flow characteristics of Cu-water nanofluid. Science in China Series E: Technological Science 2002, 45(4): 408–416.CrossRefGoogle Scholar
  11. [11]
    Wen D., Ding Y., Experimental investigation into convective heat transfer of nanofluids at the entrance region under laminar flow conditions. International Journal of Heat and Mass Transfer, 2004, 47: 5181–5188.CrossRefGoogle Scholar
  12. [12]
    Rashidi S., Akar S., Bovand M., Ellahi R., Volume of fluid model to simulate the nanofluid flow and entropy generation in a single slope solar still. Renewable Energy, 2018, 115(C): 400–410.CrossRefGoogle Scholar
  13. [13]
    Ellahi R., Zeesham A., Shehzad N., Sultan Z., Structural impact of Kerosene-Al2O3 nanoliquid on MHD Poiseuille flow with variable thermal conductivity: Application of cooling process. Journal of Molecular Liquids, 2018, 264: 607–615.CrossRefGoogle Scholar
  14. [14]
    Akbarzadeh M., Rashidi S., Karimi N., Convection of heat and thermodynamic irreversibilities in two-phase, turbulent nanofluid flows in solar heaters by corrugated absorber plates. Advanced Powder Technology, 2018, 29(9): 2243–2254.CrossRefGoogle Scholar
  15. [15]
    Shirvan K. M., Ellahi R., Mamourian M., Moghiman M., Effect of wavy surface characteristics on heat transfer in a wavy square cavity filled with nanofluid. International Journal of Heat and Mass Transfer, 2017, 107: 1110–1118.CrossRefGoogle Scholar
  16. [16]
    Ellahi R., Tariq M. H., Hassan M., Vafai K., On boundary layer magnetic flow of nano-ferroliquid under the influence of low oscillating over stretchable rotating disk. Journal of Molecular Liquids, 2017, 229: 339–345.CrossRefGoogle Scholar
  17. [17]
    Rajendran D.R., Ganapathy Sundaram E., Jawahar P., Experimental studies on the thermal performance of a parabolic dish solar receiver with the heat transfer fluids SiC + water nano fluid and water. Journal of Thermal Science, 2017, 26(3): 263–272.ADSCrossRefGoogle Scholar
  18. [18]
    Brinkman H.C., The viscosity of concentrated suspensions and solutions. Journal of Chemical Physics, 1952, 20(4): 571–581.ADSCrossRefGoogle Scholar
  19. [19]
    ANSYS Inc. ANSYS Fluent 15.0 UDF Manual, Canonsburg, PA: ANSYS Inc, 2013.Google Scholar
  20. [20]
    Manninen M., Veikko T., Sirpa K., On the mixture model for multiphase flow. Valtion Teknillinen Tutkimuskeskus publication, 1996: 3–67.Google Scholar
  21. [21]
    Schiller L., Naumann Z., A drag coefficient correlation. Zeitschrift des Vereins Deutscher Ingenieure, 1935, 77: 318: 51. (in German)Google Scholar
  22. [22]
    Sagot B., Antonini G., Christgen A., Buron F., Jet impingement heat transfer on a flat plate at a constant wall temperature. International Journal of Thermal Sciences, 2008, 47(12): 1610–1619.CrossRefGoogle Scholar
  23. [23]
    Menter F.R., Two-equation eddy-viscosity turbulence models for engineering applications. AIAA Journal, 1994, 32(8): 1598–1605.ADSCrossRefGoogle Scholar
  24. [24]
    Cadek F.F.A., Fundamental investigation of jet impingement heat transfer. Ph.D Theis. University of Cincinnati, the United States, 1968.Google Scholar
  25. [25]
    Gordon R., Akfirat J.C., Heat transfer characteristics of impinging two-dimensional air jets. ASME Journal of Heat. Transfer, 1966, 88(1): 101–108.CrossRefGoogle Scholar
  26. [26]
    Lotfi R., Saboohi Y., Rashidi A.M., Numerical study of forced convective heat transfer of nanofluids: comparison of different approaches. International Journal of Heat and Mass Transfer, 2010, 37(1): 74–78.CrossRefGoogle Scholar
  27. [27]
    Huang P.G., Mujumdar A.S., Douglas W.J.M., Numerical prediction of fluid flow and heat transfer under a turbulent impinging slot jet with surface motion and cross flow. ASME paper, 1984, 84: WA/HT–33.Google Scholar
  28. [28]
    Zuckerman N., Lior N., Jet impingement heat transfer: Physics, correlations, and numerical modeling. Advances in Heat Transfer, 2006, 39: 565–631.CrossRefGoogle Scholar
  29. [29]
    Martin H., Heat and mass transfer between impinging gas jets and solid surface. Advances in Heat Transfer, 1977, 13: 1–60.CrossRefGoogle Scholar

Copyright information

© Science Press, Institute of Engineering Thermophysics, CAS and Springer-Verlag GmbH Germany, part of Springer Nature 2019

Authors and Affiliations

  1. 1.Department of Aerospace Engineering and Applied MechanicsIndian Institute of Engineering Science and TechnologyShibpur, HowrahIndia

Personalised recommendations