Advertisement

Comparable investigation of polyaniline behavior towards gaseous ammonia and toluene adsorption

  • Amira AbdelraheemEmail author
  • Ahmed H. El-Shazly
  • Marwa Elkady
Research Article
  • 132 Downloads

Abstract

With raising awareness of gaseous air pollutants and their harmful impact, adsorption is considered one of the most prominent techniques for gaseous emissions control. The usage of polyaniline as a gas adsorbent is an innovative idea. This work aims to compare the efficacy of synthesized polyaniline nanotubes (PANT) as a novel adsorbent towards inorganic gases (ammonia NH3) and volatile organic compounds (toluene vapor). PANT was prepared via a sol-gel preparation technique. The molecular structure of prepared PANT was characterized by Fourier-transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The morphological structure was confirmed using transmission electron microscopy (TEM) and scanning electron microscope (SEM). The PANT adsorbent surface area was determined using Brunner Emmett Teller (BET). Dynamic behavior of simulated feed gas mixture of NH3 and toluene in air were examined using a fixed bed adsorption arrangement. The same adsorption conditions (inlet concentration, gas mixture feed flow rate, and a fixed amount of adsorbent) were applied for both NH3 and toluene adsorption test. The NH3 and toluene removal efficiencies were 100% and 96% respectively. Consequently, PANT is an auspicious adsorbent that can be utilized to control the indoor and outdoor gaseous air emissions.

Graphical Abstracts

Keywords

Polyaniline nanotubes Gaseous air filters Ammonia adsorption Toluene adsorption 

Notes

Acknowledgments

The author thankfully acknowledges the Egyptian ministry of higher education which granted her a fully funded Ph.D. scholarship, Egypt-Japan University (E-JUST) and Kyoto university, Japan.

Funding information

This work was supported by Egyptian Science and Technology Development Fund (STDF) (Grant no. 30735).

References

  1. Abdelraheem A, El-Shazly AH, El-Kady MF (2016) Nanofiber polyaniline and polyaniline-clay nanocomposite prepared via sonochemical and sol-gel techniques. Mater Sci Forum 860:12–16.  https://doi.org/10.4028/www.scientific.net/MSF.860.12 CrossRefGoogle Scholar
  2. Area B, Quality A, District M (2015) Petroleum refinery emissions reduction strategy : workshop report prepared by the staff of theGoogle Scholar
  3. Bhadra S, Khastgir D (2008) Extrinsic and intrinsic structural change during heat treatment of polyaniline. Polym Degrad Stab 93:1094–1099.  https://doi.org/10.1016/j.polymdegradstab.2008.03.013 CrossRefGoogle Scholar
  4. Britt D, Tranchemontagne D, Yaghi OM (2008) Metal-organic frameworks with high capacity and selectivity for harmful gases. Proc Natl Acad Sci 105:11623–11627.  https://doi.org/10.1073/pnas.0804900105 CrossRefGoogle Scholar
  5. Chang SS, Clair B, Ruelle J, Beauchene J, di Renzo F, Quignard F, Zhao GJ, Yamamoto H, Gril J (2009) Mesoporosity as a new parameter for understanding tension stress generation in trees. J Exp Bot 60:3023–3030.  https://doi.org/10.1093/jxb/erp133 CrossRefGoogle Scholar
  6. Chatterjee K, Dhara P, Ganguly S, Kargupta K, Banerjee D (2013) Morphology dependent ammonia sensing with 5-sulfosalicylic acid doped nanostructured polyaniline synthesized by several routes. Sensors Actuators B Chem 181:544–550.  https://doi.org/10.1016/j.snb.2013.02.042 CrossRefGoogle Scholar
  7. Egli M, Tereshko V, Mushudov GN, Sanishvili R, Liu X, Lewis FD (2003) Face-to-face and edge-to-face π-π interactions in a synthetic DNA hairpin with a stilbenediether linker. J Am Chem Soc 125:10842–10849.  https://doi.org/10.1021/ja0355527 CrossRefGoogle Scholar
  8. Elkady MF, El-Sayed EM, Farag HA, Zaatout AA (2014) Assessment of Novel synthetized nanozirconium tungstovanadate as cation exchanger for lead ion decontamination. J Nanomater 2014:1–11Google Scholar
  9. Gao X-Z, Liu H-J, Cheng F, Chen Y (2016) Thermoresponsive polyaniline nanoparticles: preparation, characterization, and their potential application in waterborne anticorrosion coatings. Chem Eng J 283:682–691.  https://doi.org/10.1016/j.cej.2015.08.015 CrossRefGoogle Scholar
  10. Gupta KN, Rao NJ, Agarwal GK (2012) Adsorption of xylene on granular activated carbon in a packed bed. Int J Sci Technol Res 1:90–93.  https://doi.org/10.1016/S0017-9310(98)00047-7 CrossRefGoogle Scholar
  11. Horta-Romarís L, Abad M-J, González-Rodríguez MV, Lasagabáster A, Costa P, Lanceros-Méndez S (2016) Cyclic temperature dependence of electrical conductivity in polyanilines as a function of the dopant and synthesis method. Mater Des 114:288–296.  https://doi.org/10.1016/j.matdes.2016.11.021 CrossRefGoogle Scholar
  12. Huang J (2006) Syntheses and applications of conducting polymer polyaniline nanofibers. Pure Appl Chem 78:15–27.  https://doi.org/10.1351/pac200678010015 CrossRefGoogle Scholar
  13. Huang CC, Li HS, Chen CH (2008) Effect of surface acidic oxides of activated carbon on adsorption of ammonia. J Hazard Mater 159:523–527.  https://doi.org/10.1016/j.jhazmat.2008.02.051 CrossRefGoogle Scholar
  14. Jafari S, Ghorbani-Shahna F, Bahrami A, Kazemian H (2018) Adsorptive removal of toluene and carbon tetrachloride from gas phase using Zeolitic Imidazolate Framework-8: effects of synthesis method, particle size, and pretreatment of the adsorbent. Microporous Mesoporous Mater 268:58–68.  https://doi.org/10.1016/j.micromeso.2018.04.013 CrossRefGoogle Scholar
  15. Kazim S, Ahmad S, Pfleger J, Plestil J, Joshi YM (2012) Polyaniline-sodium montmorillonite clay nanocomposites: effect of clay concentration on thermal, structural, and electrical properties. J Mater Sci 47:420–428.  https://doi.org/10.1007/s10853-011-5815-y CrossRefGoogle Scholar
  16. Kebiche H, Debarnot D, Merzouki A, Poncin-Epaillard F, Haddaoui N (2012) Relationship between ammonia sensing properties of polyaniline nanostructures and their deposition and synthesis methods. Anal Chim Acta 737:64–71.  https://doi.org/10.1016/j.aca.2012.06.003 CrossRefGoogle Scholar
  17. Kim JM, Kim JH, Lee CY, Jerng DW, Ahn HS (2018) Toluene and acetaldehyde removal from air on to graphene-based adsorbents with microsized pores. J Hazard Mater 344:458–465.  https://doi.org/10.1016/J.JHAZMAT.2017.10.038 CrossRefGoogle Scholar
  18. Kukla AL, Shirshov YM, Piletsky SA (1996) Ammonia sensors based on sensitive polyaniline films. Sensors Actuators B Chem 37:135–140.  https://doi.org/10.1016/S0925-4005(97)80128-1 CrossRefGoogle Scholar
  19. Laslau C, Zujovic Z, Travas-Sejdic J (2010) Theories of polyaniline nanostructure self-assembly: towards an expanded, comprehensive Multi-Layer Theory (MLT). Prog Polym Sci 35:1403–1419.  https://doi.org/10.1016/j.progpolymsci.2010.08.002 CrossRefGoogle Scholar
  20. Lee C, Lee S, Kim W, Ryoo R (2018) High utilization of methanol in toluene methylation using MFI zeolite nanosponge catalyst. Catal Today 303:143–149.  https://doi.org/10.1016/J.CATTOD.2017.09.056 CrossRefGoogle Scholar
  21. Lu X, Mao H, Chao D, Zhang W, Wei Y (2006) Fabrication of polyaniline nanostructures under ultrasonic irradiation: from nanotubes to nanofibers. Macromol Chem Phys 207:2142–2152.  https://doi.org/10.1002/macp.200600424 CrossRefGoogle Scholar
  22. Lubentsov BZ, Timofeeva ON, Khidekel ML (1991) Conducting polymer interaction with gaseous substances II. PANI-H2O, PANI-NH3. Synth Met 45:235–240.  https://doi.org/10.1016/0379-6779(91)91808-N CrossRefGoogle Scholar
  23. Mikhaylov S, Ogurtsov N, Noskov Y, Redon N, Coddeville P, Wojkiewicz JL, Pud A (2015) Ammonia/amine electronic gas sensors based on hybrid polyaniline–TiO 2 nanocomposites. The effects of titania and the surface active doping acid. RSC Adv 5:20218–20226.  https://doi.org/10.1039/C4RA16121A CrossRefGoogle Scholar
  24. Mishra SK, Kumari D, Gupta BD (2012) Surface plasmon resonance based fiber optic ammonia gas sensor using ITO and polyaniline. Sensors Actuators B Chem 171–172:976–983.  https://doi.org/10.1016/j.snb.2012.06.013 CrossRefGoogle Scholar
  25. Mohan N, Kannan GK, Upendra S, et al (2009) Breakthrough of toluene vapours in granular activated carbon filled packed bed reactor 168:777–781.  https://doi.org/10.1016/j.jhazmat.2009.02.079
  26. Namiesnik J (1984) Generation of standard gaseous mixtures. J Chromatogr 300:79–108.  https://doi.org/10.1016/S0021-9673(01)87581-6 CrossRefGoogle Scholar
  27. Phillips J (1995) Control and pollution prevention options for ammonia emissions control and pollution prevention options for ammonia emissions prepared by. Environ protGoogle Scholar
  28. Piri S, Zanjani ZA, Piri F, Zamani A, Yaftian M, Davari M (2016) Potential of polyaniline modified clay nanocomposite as a selective decontamination adsorbent for Pb(II) ions from contaminated waters; kinetics and thermodynamic study. J Environ Health Sci Eng 14:1–10.  https://doi.org/10.1186/s40201-016-0261-z CrossRefGoogle Scholar
  29. Qajar A, Peer M, Andalibi MR, Rajagopalan R, Foley HC (2015) Enhanced ammonia adsorption on functionalized nanoporous carbons. Microporous Mesoporous Mater 218:15–23.  https://doi.org/10.1016/j.micromeso.2015.06.030 CrossRefGoogle Scholar
  30. Ranka P, Sethi V, Contractor AQ (2016) Characterizing the oxidation level of polyaniline (PANI) at the interface of PANI/TiO2 nanoparticles under white light illumination. Thin Solid Films 615:44–55.  https://doi.org/10.1016/j.tsf.2016.06.053 CrossRefGoogle Scholar
  31. Rao P, Ankam S, Ansari M, GAVANE AG, Kumar A, Pandit VI, Nema P (2005) Monitoring of hydrocarbon emissions in a petroleum refinery. Environ Monit Assess 108:123–132.  https://doi.org/10.1007/s10661-005-3961-x CrossRefGoogle Scholar
  32. Rodrigues CC, de Moraes D, da Nóbrega SW, Barboza MG (2007) Ammonia adsorption in a fixed bed of activated carbon. Bioresour Technol 98:886–891.  https://doi.org/10.1016/j.biortech.2006.03.024 CrossRefGoogle Scholar
  33. Shao W, Jamal R, Xu F, Ubul A, Abdiryim T (2012) The effect of a small amount of water on the structure and electrochemical properties of solid-state synthesized polyaniline. Materials (Basel) 5:1811–1825.  https://doi.org/10.3390/ma5101811 CrossRefGoogle Scholar
  34. Srinivas G, Guo ZX (2014) Graphene-based materials: Synthesis and gas sorption, storage and separation. Prog Mater Sci 69:1–60.  https://doi.org/10.1016/j.pmatsci.2014.10.004 CrossRefGoogle Scholar
  35. Stejskal J, Sapurina I, Trchová M, Konyushenko EN, Holler P (2006) The genesis of polyaniline nanotubes. Polymer (Guildf) 47:8253–8262.  https://doi.org/10.1016/j.polymer.2006.10.007 CrossRefGoogle Scholar
  36. Stejskal J, Sapurina I, Trchová M, Konyushenko EN (2008) Oxidation of aniline: polyaniline granules, nanotubes, and oligoaniline microspheres. Macromolecules 41:3530–3536.  https://doi.org/10.1021/ma702601q CrossRefGoogle Scholar
  37. Sui H, Liu H, An P, He L, Li X, Cong S (2017) Application of silica gel in removing high concentrations toluene vapor by adsorption and desorption process. J Taiwan Inst Chem Eng 74:218–224.  https://doi.org/10.1016/J.JTICE.2017.02.019 CrossRefGoogle Scholar
  38. Sutar DS, Padma N, Aswal DK, Deshpande SK, Gupta SK, Yakhmi JV (2007) Preparation of nanofibrous polyaniline films and their application as ammonia gas sensor. Sensors Actuators B Chem 128:286–292.  https://doi.org/10.1016/j.snb.2007.06.015 CrossRefGoogle Scholar
  39. Sutton MA, Reis S, Baker SMH (eds) (2009) Atmospheric Ammonia. Springer Netherlands, DordrechtGoogle Scholar
  40. Thommes M, Kaneko K, Neimark AV, Olivier JP, Rodriguez-Reinoso F, Rouquerol J, Sing KSW (2015) Physisorption of gases, with special reference to the evaluation of surface area and pore size distribution (IUPAC Technical Report). Pure Appl Chem 87:1051–1069.  https://doi.org/10.1515/pac-2014-1117 CrossRefGoogle Scholar
  41. Vellingiri K, Kumar P, Deep A, Kim K-H (2017) Metal-organic frameworks for the adsorption of gaseous toluene under ambient temperature and pressure. Chem Eng J 307:1116–1126.  https://doi.org/10.1016/J.CEJ.2016.09.012 CrossRefGoogle Scholar
  42. Wang W, Liu P, Zhang M, Hu J, Xing F (2012) The pore structure of phosphoaluminate cement. Open J Compos Mater 02:104–112.  https://doi.org/10.4236/ojcm.2012.23012 CrossRefGoogle Scholar
  43. Wang J, Zhang K, Zhao L (2014) Sono-assisted synthesis of nanostructured polyaniline for adsorption of aqueous Cr(VI): effect of protonic acids. Chem Eng J 239:123–131.  https://doi.org/10.1016/j.cej.2013.11.006 CrossRefGoogle Scholar
  44. Win-Shwe T-T, Fujimaki H (2010) Neurotoxicity of toluene. Toxicol Lett 198:93–99.  https://doi.org/10.1016/J.TOXLET.2010.06.022 CrossRefGoogle Scholar
  45. World Health Organization (WHO) (2000) WHO - Toluene: Air quality guidelines. Air Qual Guidel 2:1–20.  https://doi.org/10.1128/AEM.66.9.4098-4104.2000 CrossRefGoogle Scholar
  46. Yan T, Li TX, Li H, Wang RZ (2014) Experimental study of the ammonia adsorption characteristics on the composite sorbent of CaCl2 and multi-walled carbon nanotubes. Int J Refrig 46:165–172.  https://doi.org/10.1016/j.ijrefrig.2014.02.014 CrossRefGoogle Scholar
  47. Yang X, Yi H, Tang X, Zhao S, Yang Z, Ma Y, Feng T, Cui X (2017) Behaviors and kinetics of toluene adsorption — desorption on activated carbons with varying pore structure. J Environ Sci 67:1–11.  https://doi.org/10.1016/j.jes.2017.06.032 CrossRefGoogle Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Chemical and Petrochemicals Engineering DepartmentEgypt-Japan University of Science and TechnologyNew Borg El-Arab AlexandriaEgypt
  2. 2.Occupational Health and Air Pollution Department, High Institute of Public HealthAlexandria UniversityAlexandriaEgypt
  3. 3.Chemical Engineering Department, Faculty of EngineeringAlexandria UniversityAlexandriaEgypt
  4. 4.Fabrication Technology DepartmentAdvanced Technology and New Materials Research Institute (ATNMRI), City of Scientific Research and Technology Applications (SRTA City)AlexandriaEgypt

Personalised recommendations