Advertisement

Engine parameter optimization of palm oil biodiesel as alternate fuel in CI engine

  • Akula Naresh Kumar
  • Pisipaty Srinivas KishoreEmail author
  • Kalidindi Brahma Raju
  • Nanthagopal Kasianantham
  • Ashok Bragadeshwaran
Research Article
  • 22 Downloads

Abstract

Stringent emission regulations and depletion of crude oil are driving researchers toward alternative fuels. In this context, palm oil emerges as a good competitor as it is highly economical compared to other alternative fuels. The current research work centers around the impact of palm oil methyl ester on performance, combustion, and emission characteristics at varying injection timings and exhaust gas recirculation rates. In the first phase of this research work, various blends of palm oil methyl ester with diesel with volume concentrations of 10, 20, and 30% were prepared and tested at different load conditions. Injection timing was then varied for the optimized blend. In the second phase, the impact of exhaust gas blending with fresh charge was studied at optimized injection timing. The test outcomes revealed that 20% mix of palm oil at 27° bTDC with exhaust gas blending of 20% generated higher brake thermal efficiency, higher peak pressure, and less hydrocarbon and nitrogen oxide emissions compared to diesel at standard injection timing of 23° bTDC and no blending of exhaust gases with fresh charge. However, progression of injection timing with 20% exhaust gas mixing indicated a slight penalty in smoke discharges. Brake thermal efficiency at advanced injection timing with 20% mix of exhaust gases reduced by 7.7% for diesel and increased by 6.5% for 20% blend of palm oil when compared to standard injection timing of diesel and no blending of exhaust gases. Significant diminishments in oxides of nitrogen (lessened by 6.6%) and hydrocarbons (decreased by 30.43%) have been noted for 20% mix of biodiesel at advanced injection timing with 20% exhaust gas mix contrasted to diesel at standard conditions. Therefore, the present examination prescribes 20% merging of exhaust gases for 20% blend of palm oil with advancement of injection timing for diesel engine applications.

Keywords

Biodiesel Palm oil Methyl ester Injection timing Exhaust gas recirculation 

Abbreviations

POME

Palm oil methyl ester

D

Diesel

IT

Injection timing

EGR

Exhaust gas recirculation

FFA

Free fatty acids

BSFC

Brake-specific fuel consumption

BTE

Brake thermal efficiency

HC

Hydrocarbons

CO

Carbon monoxide

CO2

Carbon dioxide

NOX

Oxides of nitrogen

FSN

Filter smoke number

HRR

Heat release rate

MFB

Mass fraction burnt

MFB50

50% of mass fraction burnt

MGT

Mean gas temperature

CA

Crank angle

ppm

Parts per million

bTDC

Before top dead center

TDC

Top dead center

POME10

90% diesel + 10% palm oil methyl ester

POME20

80% diesel + 20% palm oil methyl ester

POME30

70% diesel + 30% palm oil methyl ester

deg

Degree

Notes

References

  1. Agarwal AK, Dhar A, Gupta JG, Kim WII, Choi K, Lee CS, Park S (2015) Effect of fuel injection pressure and injection timing of Karanja biodiesel blends on fuel spray, engine performance, emissions and combustion characteristics. Energy Convers Manag 91:302–314CrossRefGoogle Scholar
  2. Ashok B, Nanthagopal K, Jeevanantham AK, Bhowmick P, Malhotra D, Agarwal P (2017a) An assessment of Calophyllum inophyllum biodiesel fuelled diesel engine characteristics using novel antioxidant additives. Energy Convers Manag 148:935–943CrossRefGoogle Scholar
  3. Ashok B, Nanthagopal K, Thundil Karuppa Raj R, Pradeep Bhasker J, Sakthi vignesh D (2017b) Influence of injection timing and exhaust gas recirculation of a Calophyllum inophyllum methyl ester fuelled CI engine. Fuel Process Technol 167:18–30CrossRefGoogle Scholar
  4. Ashok B, Nanthgopal K, Aravind M, Johny A, Tamilrasu A (2017c) Comparative analysis on the effect of zinc oxide and Ethanox as additives with biodiesel in CI engine. Energy 140:352–364CrossRefGoogle Scholar
  5. Ashok B, Nanthagopal K, Sakthi Vignesh D (2017d) Calophyllum inophyllum methyl ester biodiesel blend as an alternate fuel for diesel engine applications, Alexandria Eng J. (2017),  https://doi.org/10.1016/j.aej.2017.03.042
  6. Ashok B, Raj RTK, Nanthagopal K, Krishnan R, Subbarao R (2017e) Lemon peel oil—a novel renewable alternative energy source for diesel engine. Energy Consers Manag 139:110–121CrossRefGoogle Scholar
  7. Barik D, Murugan S, Sivaram NM, Baburaj E, Shanmuga Sundaram P (2017) Experimental investigation on the behaviour of a direct injection diesel engine fuelled with Karanja methyl ester-biogas dual fuel at different injection timings. Energy 118:127–138CrossRefGoogle Scholar
  8. Bhaskar K, Nagarajan G, Sampath S (2013) Optimization of FOME (fish oil methyl esters) blend and EGR (exhaust gas recirculation) for simultaneous control of NOX and particulate matter emissions in diesel engines. Energy 62:224–234CrossRefGoogle Scholar
  9. Can Ö, Öztürk E, Solmaz H, Aksoy F, Çinar C, Yücesu HS (2016) Combined effects of soybean biodiesel fuel addition and EGR application on the combustion and exhaust emissions in a diesel engine. Appl Therm Eng 95:115–124Google Scholar
  10. De Poures MV, Sathiyagnanam AP, Rana D, Kumar BR, Saravanan S (2017) 1-Hexanol as a sustainable biofuel in DI diesel engines and its effect on combustion and emissions under the influence of injection timing and exhaust gas recirculation (EGR). Appl Therm Eng 113:1505–1513Google Scholar
  11. Dhanaraju V, Kishore PS (2017) Effect of tamarind seed methyl ester and exhaust gas recirculation (EGR) on performance and emission characteristics of diesel engine. Int J Ambient Energy.  https://doi.org/10.1080/01430750.2017.1421579
  12. Dias JM, MCM A-F, Almeida MF (2008) Comparison of the performance of different homogeneous alkali catalysts during transesterification of waste and virgin oils and evaluation of biodiesel quality. Fuel 87:3572–3578CrossRefGoogle Scholar
  13. Esipovich AL, Rogozhin AE, Belousov AS, Kanakov EA, Danov SM (2018) A comparative study of the separation stage of rapeseed oil transesterification products obtained using various catalysts. Fuel Process Technol 173:153–164CrossRefGoogle Scholar
  14. Fattah IMR, Masjuki HH, Kalam MA, Mofijur M, Abedin MJ (2014) Effect of antioxidant on the performance and emission characteristics of a diesel engine fueled with palm biodiesel blends. Energy Convers Manag 2014:265–272Google Scholar
  15. Gad MS, EI-Araby R, Abed KA, EI-Ibiari NN, EI Morsi AK, EI-Diwani GI (2018) Performance and emission characteristics of C.I engine fueled with palm oil/palm oil methyl ester blended with diesel fuel. Egypt J Pet 27:215–219CrossRefGoogle Scholar
  16. Ganapathy T, Gakkhar RP, Murugesan K (2011) Influence of injection timing on performance, combustion and emission characteristics of Jatropha biodiesel engine. Appl Energy 88:4376–4386CrossRefGoogle Scholar
  17. Gautam R, Kumar N, Sharma P (2013) Comparative assessment of performance, emission and combustion characteristics of blends of methyl and ethyl ester of Jatropha oil and diesel in compression ignition engine. SAE Technical Paper 2013-01-2664Google Scholar
  18. Gnanasekaran S, Saravanan N, Ilangkumaran M (2016) Influence of injection timing on performance, emission and combustion characteristics of a DI diesel engine running on fish oil biodiesel. Energy 116:1218–1229CrossRefGoogle Scholar
  19. Gogoi TK, Baruah DC (2011) The use of Koroch seed oil methyl ester blends in a diesel engine. Appl Energy 88:2713–2725CrossRefGoogle Scholar
  20. Igbokwe JO, Nwofo OC, Nwaiwu CF (2015) Effects of blend on the properties, performance and emission of palm kernel oil biodiesel. Biofuels.  https://doi.org/10.1080/17597269.2015.1030719
  21. Javed S, Murthy YVVS, Satyanarayana MRS, Reddy RR, Rajagopal K (2016) Effect of zinc oxide nanoparticle fuel additive on the emission reduction of a hydrogen dual-fuelled engine with jatropha methyl ester biodiesel blends. J Clean Prod 137:490–506CrossRefGoogle Scholar
  22. Kannan GR (2013) Effect of injection pressures and timings on the performance emission and combustion characteristics of a direct injection diesel engine using biodiesel-diesel-ethanol blend. SAE Technical Paper 2013-01-1699Google Scholar
  23. Karthik N, Rajasekar R, Siva R, Mathiselvan G (2017) Experimental investigation of injection timing on the performance and exhaust emissions of a rubber seed oil blend fuel in constant speed diesel engine. Int J Ambient Energy.  https://doi.org/10.1080/01430750.2017.1392353
  24. Nagaraja S, Soorya Prakash K, Sudhakaran R, Sathish kumar M (2016) Investigation on the emission quality, performance and combustion characteristics of the compression ignition engine fueled with environmental friendly corn oil methyl ester – diesel blends. Ecotoxicol Environ Saf 134:455–461CrossRefGoogle Scholar
  25. Nanthagopal K, Ashok B, Saravanan B, Deepam P, Sudarshan B, Aaditya Ramasamy R (2018a) An assessment on the effects of 1-pentanol and 1-butanol as additives with Calophyllum inophyllum biodiesel. Energy Convers Manag 158:70–80CrossRefGoogle Scholar
  26. Nanthagopal K, Raj RTK, Ashok B, Elango T, Saravanan SV (2018b, 2018b) Influence of exhaust gas recirculation on combustion and emission characteristics of diesel engine fuelled with 100% waste cooking oil methyl ester. Waste Biomass Valorization.  https://doi.org/10.1007/s12649-018-0194-0
  27. Navas MB, Lick ID, Bolla PA, Casella ML, Ruggera JF (2018) Transesterification of soybean and castor oil with methanol and butanol using heterogeneous basic catalysts to obtain biodiesel. Chem Eng Sci 187:444–454CrossRefGoogle Scholar
  28. Nayak SK, Pattanaik BP (2014) Experimental investigation on performance and emission characteristics of a diesel engine fuelled with Mahua biodiesel using additive. Energy Procedia 54:569–579CrossRefGoogle Scholar
  29. Palash SM, Kalam MA, Masjuki HH, Masum BM, Rizwanul Fattah IM, Mofijur M (2013a) Impacts of biodiesel combustion on NOx emissions and their reduction approaches. Renew Sust Energ Rev 23:473–490CrossRefGoogle Scholar
  30. Palash SM, Masjuki HH, Kalam MA, Masum BM, Sanjid A, Abedin MJ (2013b) State of the art of NOx mitigation technologies and their effect on the performance and emission characteristics of biodiesel-fuelled compression ignition engines. Energy Convers Manag 76:400–420CrossRefGoogle Scholar
  31. Pali HS, Kumar N, Mishra C (2014) Some experimental studies on combustion, emissions and performance characteristics of an agricultural diesel engine fuelled with blends of Kusum oil methyl ester and diesel. SAE Technical Paper 2014-01-1952,  https://doi.org/10.4271/2014-01-1952
  32. Prabu SS, Asokan MA, Prathiba S, Ahmed S, Puthean G (2018) Effect of additives on performance, combustion and emission behavior of preheated palm oil/diesel blends in DI diesel engine. Renew Energy 122:196–205CrossRefGoogle Scholar
  33. Pradeep V, Sharma RP (2007) Use of hot EGR for NOx control in a compression ignition engine fuelled with bio-diesel from Jatropha oil. Renew Energy 32:1136–1154CrossRefGoogle Scholar
  34. Qi D, Leick M, Liu Y, Lee CF (2011) Effect of EGR and injection timing on combustion and emission characteristics of split injection strategy DI-diesel engine fuelled with biodiesel. Fuel 90:1884–1891CrossRefGoogle Scholar
  35. Rajesh Kumar B, Saravanan S (2015) Effect of exhaust gas recirculation (EGR) on performance and emissions of a constant speed DI diesel engine fueled with pentanol/diesel blends. Fuel 160:217–226CrossRefGoogle Scholar
  36. Sarvanan S, Nagarajan G, Sampath S (2013) Combined effect of injection timing, EGR and injection pressure in NOx control of a stationary diesel engine fuelled with crude rice bran oil methyl ester. Fuel 104:409–416CrossRefGoogle Scholar
  37. Senthil kumar S, Sivakumar G, Manoharan S (2015) Investigation of palm methyl-ester with additive on performance and emission characteristics of a diesel engine under 8-mode testing cycle. Alex Eng J 54:423–428CrossRefGoogle Scholar
  38. Shameer PM, Ramesh K (2017) Experimental evaluation on performance, combustion behaviour and influence of in-cylinder temperature on NOx emission in a DI diesel engine using thermal imager for various alternate fuel blends. Energy 118:1334–1344CrossRefGoogle Scholar
  39. Shameer PM, Ramesh K (2018) Assessment on the consequences of injection timing and injection pressure on combustion characteristics of sustainable biodiesel fuelled engine. Renew Sust Energ Rev 81:45–61CrossRefGoogle Scholar
  40. Shameer PM, Ramesh K, Sakthivel R, Purnachandran R (2017) Effects of fuel injection parameters on emission characteristics of diesel engines operating on various biodiesel: a review. Renew Sust Energ Rev 67:1267–1281CrossRefGoogle Scholar
  41. Shanmughasundaram P (2016) Experimental investigation on the emission characteristics of a variable compression ratio multi-fuel engine using palm biodiesel. Int J Ambient Energy.  https://doi.org/10.1080/01430750.2016.1155492
  42. Suresh Babu Rao H, Venkateswara Rao T, Hemachandra Reddy K (2018) Influence of injection timing on cerium oxide nanoparticle doped in waste cooking palm oil bio-diesel and diesel blends fuelled in diesel engine. Int J Ambient Energy.  https://doi.org/10.1080/01430750.2018.1472660
  43. Tashtoush GM, Al-Widyan MI, Albatayneh AM (2007) Factorial analysis of diesel engine performance using different types of biofuels. J Environ Manag 84:401–411CrossRefGoogle Scholar
  44. Teoh YH, Masjuki HH, Kalam MA, How HG (2015) Effect of injection timing and EGR on engine-out-responses of a common-rail diesel engine fuelled with neat biodiesel. RSC Adv 5:96080–96096CrossRefGoogle Scholar
  45. Tran DT, Chang JS, Lee DJ (2017) Recent insights into continuous-flow biodiesel production via catalytic and non-catalytic transesterification processes. Appl Energy 185:376–409CrossRefGoogle Scholar
  46. Vedaraman N, Puhan S, Nagarajan G, Velappan KC (2011) Preparation of palm oil biodiesel and effect of various additives on NOx emission reduction in B20: an experimental study. Int J Green Energy 8:383–397CrossRefGoogle Scholar
  47. Zheng S, Kates M, Dube MA, McLean DD (2006) Acid-catalyzed production of biodiesel from waste frying oil. Biomass Bioenergy 30:267–272CrossRefGoogle Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2019

Authors and Affiliations

  • Akula Naresh Kumar
    • 1
    • 2
  • Pisipaty Srinivas Kishore
    • 2
    Email author
  • Kalidindi Brahma Raju
    • 3
  • Nanthagopal Kasianantham
    • 4
  • Ashok Bragadeshwaran
    • 4
  1. 1.Department of Mechanical EngineeringLakireddy Bali Reddy College of EngineeringMylavaramIndia
  2. 2.Department of Mechanical Engineering, Andhra University College of Engineering (A)Andhra UniversityVisakhapatnamIndia
  3. 3.Department of Mechanical EngineeringS.R.K.R Engineering CollegeBhimavaramIndia
  4. 4.School of Mechanical EngineeringVIT UniversityVelloreIndia

Personalised recommendations