Evaluation of the Cr(VI) Adsorption Performance of Xanthate Polysaccharides Supported onto Agave Fiber-LDPE Foamed Composites

  • Arturo Y. Moreno-López
  • Martín E. González-López
  • Ricardo Manríquez-González
  • Ricardo González-Cruz
  • Aida A. Pérez-Fonseca
  • César Gómez
  • José V. Flores-Cano
  • Jorge R. Robledo-OrtízEmail author


In this work, hexavalent chromium adsorption onto LDPE and agave fiber composites coated with chitosan or cellulose was studied in batch experiments. Chemical modifications consisting in cross-linked chitosan, cross-linked chitosan xanthate, and cellulose xanthate were applied to the polysaccharide-coated sorbents in order to increase their stability and adsorption capacity. The sorbents were characterized in terms of morphology by scanning electron microscopy and their chemical composition was evaluated by infrared and nuclear magnetic resonance spectroscopies. The results showed that the adsorption kinetics followed the pseudo-second-order model in all cases (i.e., chemisorption as the rate-limiting step of the adsorption reaction). Moreover, the isotherms evidenced a monolayer adsorption on homogeneous sites described by the Langmuir model. The maximum adsorption capacity of 284.7 mg Cr(VI)/g was obtained for the cross-linked chitosan xanthate sorbent at pH 4 which represents an increase of 43% against the chitosan-coated sorbent (199.1 mg Cr(VI)/g). Besides, functionalized cellulose sorbent also increased its capacity from 84.5 to 106.0 mg Cr(VI)/g cellulose due to the xanthate group. Up to six adsorption-desorption cycles were completed for the case of functionalized chitosan sorbent, confirming that the stability was increased with the cross-linking and the material could be reused several times without losing its adsorption capacity. In the case of cellulose xanthate, only three adsorption cycles were completed. However, improvements were observed in the desorption capacity considering that it decreased below 20% after two cycles in the cellulose-coated sorbent.


Adsorption Composites Chitosan xanthate Cellulose xanthate Chromium 



  1. Afroze, S., & Sen, T. K. (2018). A review on heavy metal ions and dye adsorption from water by agricultural solid waste adsorbents. Water, Air & Soil Pollution, 229(225), 1–50.Google Scholar
  2. Babel, S., & Kurniawan, T. A. (2004). Cr (VI) removal from synthetic wastewater using coconut shell charcoal and commercial activated carbon modified with oxidizing agents and/or chitosan. Chemosphere, 54(7), 951–967.CrossRefGoogle Scholar
  3. Boddu, V. M., Abburi, K., Talbott, J. L., & Smith, E. D. (2003). Removal of hexavalent chromium from wastewater using a new composite chitosan biosorbent. Environmental Science & Technology, 37(19), 4449–4456.CrossRefGoogle Scholar
  4. Brugnerotto, J., Lizardi, J., Goycoolea, F. M., Argüelles-Monal, W., Desbrieres, J., & Rinaudo, M. (2001). An infrared investigation in relation with chitin and chitosan characterization. Polymer, 42(8), 3569–3580.CrossRefGoogle Scholar
  5. Caner, N., Sarı, A., & Tüzen, M. (2015). Adsorption characteristics of mercury (II) ions from aqueous solution onto chitosan-coated diatomite. Industrial & Engineering Chemistry Research, 54(30), 7524–7533.CrossRefGoogle Scholar
  6. Dambies, L., Guimon, C., Yiacoumi, S., & Guibal, E. (2001). Characterization of metal ion interactions with chitosan by X-ray photoelectron spectroscopy. Colloids and Surfaces A: Physicochemical and Engineering Aspects, 177, 203–214.CrossRefGoogle Scholar
  7. Debnath, S., Maity, A., & Pillay, K. (2014). Magnetic chitosan–GO nanocomposite: Synthesis, characterization and batch adsorber design for Cr (VI) removal. Journal of Environmental Chemical Engineering, 2(2), 963–973.CrossRefGoogle Scholar
  8. Deng, Y., Kano, N., & Imaizumi, H. (2017). Adsorption of Cr(VI) onto hybrid membrane of carboxymethyl chitosan and silicon dioxide. Journal of Chemistry, 2017(3426923), 1–8.CrossRefGoogle Scholar
  9. El-Reash, Y. G., Otto, M., Kenawy, I. M., & Ouf, A. M. (2011). Adsorption of Cr(VI) and as(V) ions by modified magnetic chitosan chelating resin. International Journal of Biological Macromolecules, 49(4), 513–522.CrossRefGoogle Scholar
  10. Elwakeel, K. Z. (2010). Removal of Cr (VI) from alkaline aqueous solutions using chemically modified magnetic chitosan resins. Desalination, 250(1), 105–112.CrossRefGoogle Scholar
  11. Fernández-Pazos, M. T., Garrido-Rodriguez, B., Nóvoa-Muñoz, J. C., Arias-Estévez, M., Fernández-Sanjurjo, M. J., Núñez-Delgado, A., et al. (2013). Cr(VI) adsorption and desorption on soils and biosorbents. Water, Air & Soil Pollution, 224, 1366, 1–1366,12.CrossRefGoogle Scholar
  12. García-Sánchez, M. E., Pérez-Fonseca, A. A., Gómez, C., González-Reynoso, O., Vázquez-Lepe, M. O., González-Núñez, R., et al. (2017). Improvement of Pb (II) adsorption capacity by controlled alkali treatment to chitosan supported onto agave fiber-HDPE composites. Macromolecular Symposia, 374(1), 1600104.CrossRefGoogle Scholar
  13. Habiba, U., Afifi, A. M., Salleh, A., & Ang, B. C. (2017). Chitosan/(polyvinyl alcohol)/zeolite electrospun composite nanofibrous membrane for adsorption of Cr6+, Fe3+ and Ni2+. Journal of Hazardous Materials, 322, 182–194.CrossRefGoogle Scholar
  14. Heidari, A., Younesi, H., Mehraban, Z., & Heikkinen, H. (2013). Selective adsorption of Pb (II), Cd (II), and Ni (II) ions from aqueous solution using chitosan–MAA nanoparticles. International Journal of Biological Macromolecules, 61, 251–263.CrossRefGoogle Scholar
  15. Hirano, S., Usutani, A., & Midorikawa, T. (1997). Novel fibers of N-acylchitosan and its cellulose composite prepared by spinning their aqueous xanthate solutions. Carbohydrate Polymers, 33(1), 1–4.CrossRefGoogle Scholar
  16. Huang, G., Zhang, H., Shi, J. X., & Langrish, T. A. (2009). Adsorption of chromium (VI) from aqueous solutions using cross-linked magnetic chitosan beads. Industrial & Engineering Chemistry Research, 48(5), 2646–2651.CrossRefGoogle Scholar
  17. Kalantari, K., Ahmad, M. B., Masoumi, H. R. F., Shameli, K., Basri, M., & Khandanlou, R. (2015). Rapid and high capacity adsorption of heavy metals by Fe3O4/montmorillonite nanocomposite using response surface methodology: Preparation, characterization, optimization, equilibrium isotherms, and adsorption kinetics study. Journal of the Taiwan Institute of Chemical Engineers, 49(4), 192–198.CrossRefGoogle Scholar
  18. Kasaai, M. R. (2010). Determination of the degree of N-acetylation for chitin and chitosan by various NMR spectroscopy techniques: a review. Carbohydrate Polymers, 79(4), 801–810.CrossRefGoogle Scholar
  19. Kavaklı, C., Barsbay, M., Tilki, S., Güven, O., & Kavaklı, P. A. (2016). Activation of polyethylene/polypropylene nonwoven fabric by radiation-induced grafting for the removal of Cr(VI) from aqueous solutions. Water, Air & Soil Pollution, 227, 473, 1–473,16.CrossRefGoogle Scholar
  20. Klapiszewski, Ł., Bartczak, P., Wysokowski, M., Jankowska, M., Kabat, K., & Jesionowski, T. (2015). Silica conjugated with Kraft lignin and its use as a novel ‘green’ sorbent for hazardous metal ions removal. Chemical Engineering Journal, 260, 684–693.CrossRefGoogle Scholar
  21. Kulkarni, P. S., Deshmukh, P. G., Jakhade, A. P., Kulkarni, S. D., & Chikate, R. C. (2017). 1,5 diphenylcarbazide immobilized cross-linked chitosan films: an integrated approach towards enhanced removal of Cr (VI). Journal of Molecular Liquids, 247, 254–261.CrossRefGoogle Scholar
  22. Kumar, A. S. K., Gupta, T., Kakan, S. S., Kalidhasan, S., Rajesh, V., & Rajesh, N. (2012). Effective adsorption of hexavalent chromium through a three center (3c) co-operative interaction with an ionic liquid and biopolymer. Journal of Hazardous Materials, 239-240, 213–224.CrossRefGoogle Scholar
  23. Lin, H., Han, S., Dong, Y., Ling, W., & He, Y. (2018). Structural characteristics and functional properties of corncob modified by hyperbranched polyamide for the adsorption of Cr (VI). Water, Air & Soil Pollution, 229, 117, 1–117,12.Google Scholar
  24. McCormick, C. L., Callais, P. A., & Hutchinson, B. H., Jr. (1985). Solution studies of cellulose in lithium chloride and N, N-dimethylacetamide. Macromolecules, 18(12), 2394–2401.CrossRefGoogle Scholar
  25. Mirabedini, M., Kassaee, M. Z., & Poorsadeghi, S. (2017). Novel magnetic chitosan hydrogel film, cross-linked with glyoxal as an efficient adsorbent for removal of toxic Cr(VI) from water. Arabian Journal for Science and Engineering, 45(1), 115–124.CrossRefGoogle Scholar
  26. Miretzky, P., & Cirelli, A. F. (2010). Cr (VI) and Cr (III) removal from aqueous solution by raw and modified lignocellulosic materials: a review. Journal of Hazardous Materials, 180(1–3), 1–19.CrossRefGoogle Scholar
  27. Ngah, W. W., Ab Ghani, S., & Kamari, A. (2005). Adsorption behaviour of Fe (II) and Fe (III) ions in aqueous solution on chitosan and cross-linked chitosan beads. Bioresource Technology, 96(4), 443–450.CrossRefGoogle Scholar
  28. Nguyen, T. C., Loganathan, P., Nguyen, T. V., Vigneswaran, S., Kandasamy, J., & Naidu, R. (2015). Simultaneous adsorption of Cd, Cr, Cu, Pb, and Zn by an iron-coated Australian zeolite in batch and fixed-bed column studies. Chemical Engineering Journal, 270, 393–404.CrossRefGoogle Scholar
  29. Pang, L. J., Li, R., Gao, Q. H., Hu, J. T., Xing, Z., Zhang, M. X., et al. (2016). Functionalized and reusable polyethylene fibres for Au (III) extraction from aqueous solution with high adsorption capacity and selectivity. RSC Advances, 6, 87221–87229.CrossRefGoogle Scholar
  30. Park, D., Lim, S. R., Yun, Y. S., & Park, J. M. (2008). Development of a new Cr (VI)-biosorbent from agricultural biowaste. Bioresource Technology, 99(18), 8810–8818.CrossRefGoogle Scholar
  31. Pérez-Fonseca, A. A., Gómez, C., Dávila, H., González-Núnez, R., Robledo-Ortíz, J. R., Vázquez-Lepe, M. O., et al. (2011). Chitosan supported onto agave fiber—postconsumer HDPE composites for Cr (VI) adsorption. Industrial & Engineering Chemistry Research, 51(17), 5939–5946.CrossRefGoogle Scholar
  32. Putro, J. N., Santoso, S. P., Ismadji, S., & Ju, Y. H. (2017). Investigation of heavy metal adsorption in binary system by nanocrystalline cellulose–bentonite nanocomposite: improvement on extended. Langmuir isotherm model. Microporous and Mesoporous Materials, 246(7), 166–177.CrossRefGoogle Scholar
  33. Rojas, G., Silva, J., Flores, J. A., Rodriguez, A., Ly, M., & Maldonado, H. (2005). Adsorption of chromium onto cross-linked chitosan. Separation and Purification Technology, 44(1), 31–36.CrossRefGoogle Scholar
  34. Sağ, Y., & Aktay, Y. (2002). Kinetic studies on sorption of Cr (VI) and Cu (II) ions by chitin, chitosan and Rhizopus arrhizus. Biochemical Engineering Journal, 12(2), 143–153.CrossRefGoogle Scholar
  35. Saleh, T. A. (2015). Isotherm, kinetic, and thermodynamic studies on Hg (II) adsorption from aqueous solution by silica-multiwall carbon nanotubes. Environmental Science and Pollution Research, 22(21), 16721–16731.CrossRefGoogle Scholar
  36. Sankararamakrishnan, N., Dixit, A., Iyengar, L., & Sanghi, R. (2006). Removal of hexavalent chromium using a novel cross linked xanthated chitosan. Bioresource Technology, 97(18), 2377–2382.CrossRefGoogle Scholar
  37. Schmuhl, R., Krieg, H. M., & Keizer, K. (2001). Adsorption of cu (II) and Cr (VI) ions by chitosan: Kinetics and equilibrium studies. Water SA, 27(1), 1–7.Google Scholar
  38. Soltani, R. D. C., Khorramabadi, G. S., Khataee, A. R., & Jorfi, S. (2014). Silica nanopowders/alginate composite for adsorption of lead (II) ions in aqueous solutions. Journal of the Taiwan Institute of Chemical Engineers, 45(3), 973–980.CrossRefGoogle Scholar
  39. Spinelli, V. A., Laranjeira, M. C., & Fávere, V. T. (2004). Preparation and characterization of quaternary chitosan salt: adsorption equilibrium of chromium (VI) ion. Reactive and Functional Polymers, 61(3), 347–352.CrossRefGoogle Scholar
  40. Sun, X., Yang, L., Li, Q., Zhao, J., Li, X., Wang, X., et al. (2014). Amino-functionalized magnetic cellulose nanocomposite as adsorbent for removal of Cr (VI): synthesis and adsorption studies. Chemical Engineering Journal, 241, 175–183.CrossRefGoogle Scholar
  41. Tingaut, P., Hauert, R., & Zimmermann, T. (2011). Highly efficient and straightforward functionalization of cellulose films with thiol-ene click chemistry. Journal of Materials Chemistry, 21(40), 16066–16076.CrossRefGoogle Scholar
  42. Unuabonah, E. I., Olu-Owolabi, B. I., & Adebowale, K. O. (2016). Competitive adsorption of metal ions onto goethite–humic acid-modified kaolinite clay. International journal of Environmental Science and Technology, 13(4), 1043–1054.CrossRefGoogle Scholar
  43. Weber, W. J., & Morris, J. C. (1963). Kinetics of adsorption on carbon from solution. Journal of the Sanitary Engineering Division, 89(2), 31–60.Google Scholar
  44. Wu, Z., Li, S., Wan, J., & Wang, Y. (2012). Cr (VI) adsorption on an improved synthesized cross-linked chitosan resin. Journal of Molecular Liquids., 170, 25–29.CrossRefGoogle Scholar
  45. Xu, X., Gao, B. Y., Tang, X., Yue, Q. Y., Zhong, Q. Q., & Li, Q. (2011). Characteristics of cellulosic amine-crosslinked copolymer and its sorption properties for Cr (VI) from aqueous solutions. Journal of Hazardous Materials, 189(1), 420–426.CrossRefGoogle Scholar
  46. Yakout, A. A., El-Sokkary, R. H., Shreadah, M. A., & Hamid, O. G. A. (2016). Removal of Cd (II) and Pb (II) from wastewater by using triethylenetetramine functionalized grafted cellulose acetate-manganese dioxide composite. Carbohydrate Polymers, 148, 406–414.CrossRefGoogle Scholar
  47. Yang, R., Aubrecht, K. B., Ma, H., Wang, R., Grubbs, R. B., Hsiao, B. S., et al. (2015). Thiol-modified cellulose nanofibrous composite membranes for chromium (VI) and lead (II) adsorption. Polymer, 55(5), 1167–1176.CrossRefGoogle Scholar
  48. Yu, J. X., Wang, L. Y., Chi, R. A., Zhang, Y. F., Xu, Z. G., & Guo, J. (2015). Adsorption of Pb 2+, Cd 2+, Cu 2+, and Zn 2+ from aqueous solution by modified sugarcane bagasse. Research on Chemical Intermediates, 41(3), 1525–1541.CrossRefGoogle Scholar
  49. Zhang, L., Xia, W., Liu, X., & Zhang, W. (2015). Synthesis of titanium cross-linked chitosan composite for efficient adsorption and detoxification of hexavalent chromium from water. Journal of Materials Chemistry A, 3, 331–340.CrossRefGoogle Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  • Arturo Y. Moreno-López
    • 1
  • Martín E. González-López
    • 2
  • Ricardo Manríquez-González
    • 1
  • Ricardo González-Cruz
    • 1
  • Aida A. Pérez-Fonseca
    • 2
  • César Gómez
    • 2
  • José V. Flores-Cano
    • 3
  • Jorge R. Robledo-Ortíz
    • 1
    Email author
  1. 1.Departamento de Madera, Celulosa y PapelUniversidad de GuadalajaraZapopanMexico
  2. 2.Departamento de Ingeniería QuímicaUniversidad de GuadalajaraGuadalajaraMexico
  3. 3.Facultad de Ciencias de la TierraUniversidad Autónoma de Nuevo LeónLinaresMexico

Personalised recommendations