Advertisement

Tribology Letters

, 67:100 | Cite as

Abrasive Wear Behavior and Its Relation with the Macro-indentation Fracture Toughness of an Fe-Based Super-Hard Hardfacing Deposit

  • Mohtasham Bahoosh
  • Hamid Reza ShahverdiEmail author
  • Amirreza Farnia
Original Paper
  • 43 Downloads

Abstract

In this study, flux-cored arc welding was performed to deposit an Fe-based super-hard hardfacing whit 911 HV30 on an st37 substrate. The dry sand/rubber wheel abrasion test (ASTM G65) was performed to investigate the abrasive wear behavior of the hardfacing deposit and its average weight loss was measured to be 0.075 gr. The worn surface and cross sections of wear sample were studied by optical microscopy and scanning electron microscopy. The results showed that the fracture behavior of the phases during abrasion testing is similar to their fracture behavior during macro-indentation fracture toughness testing investigated in the previous study (Bahoosh et al. in Eng Fail Anal 92:480–494,  https://doi.org/10.1016/j.engfailanal.2018.06.021, 2018). Consequently, the micro-mechanisms of abrasion resistance associated with the fracture behavior of the phases such as the fragmentation of the primary \({\text{M}}_{7} \left({\text{CB}} \right)_{3}\) in the preferred direction and higher abrasion resistance of the core–rim-structured phases were determined.

Keywords

Fe-based super-hard hardfacing Abrasive wear behavior Fracture mechanism ASTM-G65 Macro-indentation fracture toughness test 

Notes

Supplementary material

11249_2019_1213_MOESM1_ESM.rar (35.9 mb)
Supplementary material 1 (RAR 36753 kb)

References

  1. 1.
    Abrasion resistant applications. Corodur welding wire Co. https://www.corodur.de/en/products/abrasion-resistant-applications (2019). Accessed 1 July 2019
  2. 2.
    ASTM-G65: Standard test method for measuring abrasion using the dry sand/rubber wheel apparatus. ASTM Int., West Conshohocken (2010)Google Scholar
  3. 3.
    Petrica, M., Katsich, C., Badisch, E., Kremsner, F.: Study of abrasive wear phenomena in dry and slurry 3-body conditions. Tribol. Int. 64, 196–203 (2013).  https://doi.org/10.1016/j.triboint.2013.03.028 CrossRefGoogle Scholar
  4. 4.
    Yüksel, N., Şahin, S.: Wear behavior–hardness–microstructure relation of Fe–Cr–C and Fe–Cr–C–B based hardfacing alloys. Mater. Des. 58, 491–498 (2014).  https://doi.org/10.1016/j.matdes.2014.02.032 CrossRefGoogle Scholar
  5. 5.
    Bedolla-Jacuinde, A., Guerra, F.V., Mejía, I., Zuno-Silva, J., Rainforth, M.: Abrasive wear of V-Nb–Ti alloyed high-chromium white irons. Wear 332, 1006–1011 (2015).  https://doi.org/10.1016/j.wear.2015.01.049 CrossRefGoogle Scholar
  6. 6.
    Gualco, A., Svoboda, H.G., Surian, E.S.: Study of abrasive wear resistance of Fe-based nanostructured hardfacing. Wear 360, 14–20 (2016).  https://doi.org/10.1016/j.wear.2016.04.011 CrossRefGoogle Scholar
  7. 7.
    Hutchings, I.M., Shipway, P.: Tribology. Friction and Wear of Engineering Materials. Presented at the (2017)CrossRefGoogle Scholar
  8. 8.
    Hutchings, I.M.: Tribological properties of metal matrix composites. Mater. Sci. Technol. 10(6), 513–517 (1994).  https://doi.org/10.1179/mst.1994.10.6.513 CrossRefGoogle Scholar
  9. 9.
    Correa, E.O., Alcântara, N.G., Tecco, D.G., Kumar, R.V.: The relationship between the microstructure and abrasive resistance of a hardfacing alloy in the Fe-Cr-C-Nb-V system. Metall. Mater. Trans. A 38(8), 1671–1680 (2007).  https://doi.org/10.1007/s11661-007-9220-8 CrossRefGoogle Scholar
  10. 10.
    Doǧan, Ö.N., Hawk, J.A.: Effect of carbide orientation on abrasion of high Cr white cast iron. Wear 189(1–2), 136–142 (1995).  https://doi.org/10.1016/0043-1648(95)06682-9 CrossRefGoogle Scholar
  11. 11.
    Coronado, J.J.: Effect of (Fe, Cr)7C3 carbide orientation on abrasion wear resistance and fracture toughness. Wear 270(3–4), 287–293 (2011).  https://doi.org/10.1016/j.wear.2010.10.070 CrossRefGoogle Scholar
  12. 12.
    Meacham, B.E., Marshall, M.C., Branagan, D.J.: Palmqvist fracture toughness of a new wear-resistant weld alloy. Metall. Mater. Trans. A 37(12), 3617–3627 (2006).  https://doi.org/10.1007/s11661-006-1056-0 CrossRefGoogle Scholar
  13. 13.
    Chotěborský, R.: Effect of heat treatment on the microstructure, hardness and abrasive wear resistance of high chromium hardfacing. Res. Agric. Eng. 59, 23–28 (2013)CrossRefGoogle Scholar
  14. 14.
    Bahoosh, M., Shahverdi, H.R., Farnia, A.: Macro-indentation fracture mechanisms in a super-hard hardfacing Fe-based electrode. Eng. Fail. Anal. 92, 480–494 (2018).  https://doi.org/10.1016/j.engfailanal.2018.06.021 CrossRefGoogle Scholar
  15. 15.
    ISO 28079: Hardmetals—Palmqvist Toughness Test. International Organization for Standardization, Geneva (2009)Google Scholar
  16. 16.
    Sarin, V.K., Llanes, L., Mari, D.: Comprehensive Hard Materials, vol. 1, pp. 304–320. Elsevier, Amsterdam (2014)Google Scholar
  17. 17.
    basic welding filler metal technology, lesson viii: hardsurfacing electrodes. ESAB Co. http://www.esabna.com/euweb/awtc/lesson8_1.htm. Accessed 1 July 2019
  18. 18.
    Buchely, M.F., Gutierrez, J.C., León, L.M., Toro, A.: The effect of microstructure on abrasive wear of hardfacing alloys. Wear 259(1–6), 52–61 (2005).  https://doi.org/10.1016/j.wear.2005.03.002 CrossRefGoogle Scholar
  19. 19.
    Kirchgaßner, M., Badisch, E., Franek, F.: Behaviour of iron-based hardfacing alloys under abrasion and impact. Wear 265(5–6), 772–779 (2008).  https://doi.org/10.1016/j.wear.2008.01.004 CrossRefGoogle Scholar
  20. 20.
    Lin, C.-M., Chang, C.-M., Chen, J.-H., Wu, W.: Hardness, toughness and cracking systems of primary (Cr, Fe)23C6 and (Cr, Fe)7C3 carbides in high-carbon Cr-based alloys by indentation. Mater. Sci. Eng., A 527(18–19), 5038–5043 (2010).  https://doi.org/10.1016/j.msea.2010.04.073 CrossRefGoogle Scholar
  21. 21.
    Lee, S., Choo, S.-H., Kim, N.J., Baek, E.-R., Ahn, S.: Correlation of microstructure and fracture toughness in high-chromium white iron hardfacing alloys. Metall. Mater. Trans. A 27(12), 3881–3891 (1996).  https://doi.org/10.1007/BF02595637 CrossRefGoogle Scholar
  22. 22.
    Zhou, Y.F., Qin, G.K., Jiang, P.J., Wang, S.F., Qi, X.W., Xing, X.L., Yang, Q.X.: Dry sliding wear behavior of (Cr, Fe)7C3-γ(Cr, Fe) metal matrix composite (MMC) coatings: the influence of high volume fraction (Cr, Fe)7C3 carbide. Tribol. Lett. 66(3), 108 (2018).  https://doi.org/10.1007/s11249-018-1053-7 CrossRefGoogle Scholar
  23. 23.
    Polak, R., Ilo, S., Badisch, E.: Relation between inter-particle distance (L IPD) and abrasion in multiphase matrix-carbide materials. Tribol. Lett. 33(1), 29–35 (2009).  https://doi.org/10.1007/s11249-008-9388-0 CrossRefGoogle Scholar
  24. 24.
    Adamiak, M., Górka, J., Kik, T.: Comparison of abrasion resistance of selected constructional materials. J. Achiev. Mater. Manuf. Eng. 37(2), 375–380 (2009)Google Scholar
  25. 25.
    Dasgupta, R., Prasad, B.K., Modi, O.P., Jha, A.K.: A comparison of material removal mechanism under low stress abrasive condition of steel and hardfacing alloys. J. Mater. Eng. Perform. 8(4), 437–442 (1999).  https://doi.org/10.1361/105994999770346738 CrossRefGoogle Scholar
  26. 26.
    Tang, X.H., Li, L., Hinckley, B., Dolman, K., Parent, L., Li, D.Y.: Beneficial effects of the core-shell structure of primary carbides in high-Cr (45 wt%) white cast irons on their mechanical behavior and wear resistance. Tribol. Lett. 58(3), 44 (2015).  https://doi.org/10.1007/s11249-015-0522-5 CrossRefGoogle Scholar
  27. 27.
    Berns, H.: Comparison of wear resistant MMC and white cast iron. Wear 254(1–2), 47–54 (2003).  https://doi.org/10.1016/S0043-1648(02)00300-9 CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2019

Authors and Affiliations

  • Mohtasham Bahoosh
    • 1
  • Hamid Reza Shahverdi
    • 1
    Email author
  • Amirreza Farnia
    • 2
  1. 1.Department of Materials EngineeringTarbiat Modares UniversityTehranIran
  2. 2.Department of Materials Engineering, Science and Research BranchIslamic Azad UniversityTehranIran

Personalised recommendations